Plus Projector U5 732 User Manual

E-21
CrCbY
Pr Pb YCOMPONENT
COMPONENT
Connecting Personal Computers and Video Equipment
Connections with Component Signals
When the Video Equipment Has a YCbCr Connector or YPbPr Connector
•The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “Compo-
nent” using the menu sequence of [Setup] → [Input Format] → [RGB].
See “Input Format” on Page E-56.
•When projecting the YCbCr signal or YPbPr signal, if the color of the overall image...

E-22
Connecting Personal Computers and Video Equipment
* Make the connection to the projector’s AUDIO jack using the supplied audio cable. When the audio jack of the equipment that
is to be connected is of the RCA phono type, make connection via the supplied audio conversion adapter.
* The built-in speaker of the projector provides monaural audio. To enjoy convincing audio reproduction, please connect the
audio output of the video equipment to your audio system.
* The built-in speaker outputs the audio...

E-23
Power Cable Connections and Switching the Power On/Off
STAN
D
BY ST
ATU
SSTANDBY
AUTO
SOURCE
RGB
S VIDEO
VIDEO
AUDIO
MOUSE
PC CONTROL
There is an order in which the power cable is connected and the power is switched on/off.
Operating
1Connect the AC IN connector of the projector and the power outlet using the supplied power cable.The STANDBY indicator will light in amber, and the unit will enter the standby mode.
Firmly plug in all the way.
To wall outlet
2Switch on the projector powerPress the...

E-24
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Lan-
guage Select] will be displayed. Follow the procedure described be-
low and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clock-
wise to focus it. See Page E-27.
1Press the SELECT (
) buttons of the Remote con-
trol and align the deep blue cursor with [English].
Cursor
2Press the ENTER button to set....

E-25
Power Cable Connections and Switching the Power On/Off
Finishing
1Switch off the power of the connected equip-
ment
2Switch off the power of the projector
Press the STANDBY button.
The [Power Off] display appears.
When the level gauge reaches maximum, the projection screen
will go off (in about 5 seconds) and the projector will enter the
power-off operation.
Note
* The operation can be cancelled by pressing a button other than
the STANDBY button.
* One more press of the STANDBY button will switch...

E-26
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
Adjustment of the Projection Screen
2
(2)
(1)(3)
(4)
(5)(3)(4)
Turn the zoom ring to adjust the screen size of the projection image.Adjust the image to match the desired screen size. When outside of the adjustment range, move the projector to the rear or
forward.1
Zoom ring
Adjust the projection image to the screen.Check that the screen is...

E-27
Adjustment of the Projection Screen
3Turn the focus ring and adjust the focus of the screen
Note:
When the projector has a suspended or rear installation is used, the orientation of the projection will need to be changed.
Please see “Vertical Flip” on Page E-53.
Focus ring
STA
N
D
B
Y ST
A
T
U
SSTANDBY
AUTO
SOURCE
R
G
B
S
 V
ID
E
O
V
ID
E
O
A
U
D
IO
M
O
U
S
E
P
C
 C
O
N
T
R
O
L
Making Adjustments with the Adjusters
Raising the projection image
While viewing the projection image, (1) press and hold...

E-28
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see “Menu Operation Method” on Page E-40 and the various items on
Pages E-47 to E-60.
Input Selection
This operation selects the input signal to be projected.
Main unit operation: Press the SOURCE button.
(It will not function while the menu or the quick menu is displayed.)
When Auto Source is On
Whenever the SOURCE button is pressed, the...

E-29
General Operation
Automatic Adjustment
This function automatically adjusts the position shift, screen size, vertical stripes,
and color infidelity of the projected analog RGB input signal.
Normally automatic adjustment is performed at the time of signal selection.
Main unit operation/Remote control operation: Press the AUTO button.
(This will not function while the menu or the quick menu is displayed.)
A press of the AUTO button starts the automatic adjustment.
Note:
* If the display position is...

E-30
Freezing a Moving Picture
This function is used to stop and view a moving picture. Note that the input
image continues to advance even though the picture there is a still picture
condition.
A press of the FREEZE button changes the screen to a still picture. A
further press returns the screen to a moving picture.
General Operation
MUTELASER
AUTO
TIMER
VOL
ZOOM RGBVIDEO
R-CLICK/
CANCEL
QUICK MENU
ENTER
STANDBY
Q
12
34
FREEZE
Cancelling Video and Audio Temporarily
This function is used to cancel the...