Plus Projector U5 732 User Manual

E-11
Names of the Remote Control Parts/Preparing the Remote Control
Refer to the description (and diagram) for the remote control unit included with your projector.
Names of Parts/Preparing the Remote Control Unit
FREEZEMUTELASER
AUTO
TIMER
VOL
ZOOM RGBVIDEO
R-CLICK/
CANCEL
QUICK MENU
ENTER
STANDBY
Q
12
34
VOL button [E-31]
(Volume adjustment) STANDBY button [E-23, 25]
This button is used to switch ON
the power aand set the unit to the
STANDBY mode.
AUTO button [E-28]
(Automatic adjustment of the RGB...

E-12
Names of the Remote Control Parts/Preparing the Remote Control
Inserting the Batteries
When using the remote control for the first time, install the batteries that were supplied.
2Insert the batteries to match the + and – as indi-
cated inside the compartment.1Slide the battery compartment cover (located on the
bottom of the remote control) and pull off.
* When replacing batteries, purchase two of the same type of AAA battery.
* DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
(B)(C)(A)
3(A)...

E-13
Remote Control Range
Point the infrared transmitter of the remote control toward the remote control sensor located at the front or rear of the main unit
and operate.
Reception of the remote control signal should generally be possible within the range illustrated below.
Precautions
Handling of the Remote Control
* Exposure of the main units remote control sensor or the remote control infrared transmitter to bright light or the
obstruction of the signal by an obstacle located in the pathway may...

E-14
The Procedure Up to Projecting to the Screen
Perform setup adjustments in the following order.
1Position the projectorDetermine the locations to set up the screen and the projector.
See “Placement Guide” on Page E-15.
2Connect the video equipment and personal computer
Connect your equipment to the projector.
When making connections with the personal computer’s RGB connector, see “Connections with
Personal Computer” on Page E-18.
When making connections with the video equipment’s video connector or...

E-15
Placement Guide
•The projection distance over which focussing is adjustable is 1.20 m (3.94 feet) to 13.81 m (45.31 feet). The projector
should be placed within this range.
Screen Size and Projection Distance
•Use this information as a guide to find out about the screen size when the projector is placed at a certain location, or
to find out the approximate size of a screen that will be required.
•Refer to the projection distance table for your projector model.
•When suspending the projector from the...

E-16
Placement Guide
* There is a tolerance of ±5% due to design values.
* This table uses the lens apex and lens center as references and requires that the projector be in a horizontal condition
(with front and rear adjusters fully withdrawn).27"
33"
40"
60"
80"
100"
120"
150"
200"
250"
300"0.560.41
0.670.50
0.810.61
1.210.91
1.621.21
2.031.52
2.431.82
3.042.28
4.063.04
5.083.81
6.094.57—–1.20
1.23–1.48
1.49–1.80
2.26–2.73
3.03–3.65
3.80–4.57...

E-17
Placement Guide
Installation Height of Projection Screen [Reference]
Once the installation location and position have been decided, the projection height should be checked. In the case of large
screen sizes, there are instances where the image cannot be projected within the floor to ceiling height.
The required installation height can be found using the following formula:
[Height from center of lens to top edge of the projection] m (feet) + 0.05m (0.16 feet) + Stand height
Example: Using a 150"...

E-18
Connecting Personal Computers and Video Equipment
Connecting this unit with a personal computer permits presentation data to be projected as a large screen display at
conferences, lectures, and on other occasions. Furthermore, connecting this unit to a DVD player or other video equip-
ment source in combination with an audio/video amplifier and speaker system will allow you to enjoy convincing home
theater.
Connections with Personal Computer
Please check the following before making connections with...

E-19
Connecting Personal Computers and Video Equipment
To Output the External Output Signal of a Notebook Computer
When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook
computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your
notebook computer or the on-line help while performing the following procedure.
1Check whether a signal is being sent from the notebook...

E-20
VIDEOS-VIDEO
Connecting Personal Computers and Video Equipment
Connections with Composite Signals
Video Equipment with VIDEO Connectors
•Make the connection to the VIDEO connector of the projector using the supplied Video cable.
•The input setting of the VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project, please
change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input Format]
→ [Video].
See...