Philips Mx5800sa User Manual

11
English
Step 4: Placing the speakers
and subwoofers
For best possible surround sound, all the
speakers should be placed at the same distance
from the listening position.
1Place the left and right front speakers with
subwoofer stands at equal distances from the
TV and at an angle of approximately 45
degrees from the listening position.
2Place the centre speaker above the TV or the
DVD system so that the centre channel’s
sound is localised.
3Place the surround speakers at normal
listening ear level...

12
EnglishStep 6:Connecting TV
Connections
IMPORTANT!
–You only need to make one video
connection from the following options,
depending on the capabilities of your TV
system.
–Connect the DVD system directly to
the TV.
Using Composite Video jack
(CVBS)
1Use the composite video cable (yellow) to
connect the DVD system’s CVBS jack to the
video input jack (or labelled as A/V In,  Video In,
Composite or Baseband) on the TV.
2To hear the TV channels through this DVD
system, use the audio cables (white / red)...

13
English
P-SCANON       OFF
Pb
DIGITAL 
OUT
DIGITAL 
INAUX
INTV
INLINE
OUT AUDIO
VIDEO 
OUT
CVBS
S-VIDEO
FM ANTENNA MW
L
RY
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO INCOMPONENT
VIDEO IN
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO INCOMPONENT
VIDEO IN
1
Pr
2
SURROUND CENTER FRONT
L
R
SL
SRC
SUB-WOOFER
3
Connections
IMPORTANT!–If your TV only has a single Antenna In
jack (or labelled as 75 ohm or RF In),
you will need an RF modulator in order
to view the DVD playback on the TV.
See your electronics retailer...

14
English
Connections
After everything is connected
properly,
1Set the VOLTAGE SELECTOR to the local
power line voltage.
2Plug in the AC power cord to the power
outlet.
Never make or change any connections with
the power switched on.
On the DVD system,
AUTO INSTALL – PRESS PLAY may
appear on the display panel.  Press ÉÅ  on the
front panel to store all available radio stations
or press Ç to exit (see page 40 “Tuner
Operations”).
               DVD VIDEO DIGITAL SURROUND SYSTEMSTO P PLAY  PAUSE...

15
English
Connections (optional)
Connecting a VCR or
Cable/Satellite Box
DIGITAL 
OUT
DIGITAL 
INAUX
INTV
INLINE
OUT AUDIO
VIDEO 
OUT
CVBS
S-VIDEOFM ANTENNA MW
L
R
Pr
YPb
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
24
3
1
SPEAKER SYSTEMS (4Ω)
SURROUND CENTER FRONT
L
R
SL
SRCSUB-WOOFER
P-SCANON       OFF
ANT IN
TO TVVCR or
Cable/Satellite Box
Viewing and listening to the playback
1Connect the VCR or Cable / Satellite Box to
the TV as shown.
2Connect the DVD system’s AUX IN (R/L)
jacks...

16
English
Functional Overview
* = Press and hold the button for more than two seconds.
1STANDBY ON– Switches to Eco Power standby mode or turns
on the system.
– *Switches to standby mode.
2Disc trays 1~5
3OPEN•CLOSE 0 (DISC1~5)– Opens / Closes the individual disc tray.
4iR SENSOR– Point the remote control towards this sensor.
5Speaker display panel
6System display panel
7TUNING– Switches between frequency tuning and preset
tuning mode.
8PROG (PROGRAM)– DISC: starts programming.
– TUNER: starts...

17
English
Functional Overview
Control buttons available on the
remote only
*SYSTEM MENU (DVD mode only)
– Enters or exits system setup menu.
(Joystick 1 2 3 4– Selects movement direction in the menu.
– Use 1 2 to select a preset radio station.
)OK– Confirms a selection.
¡DISC SKIP– Selects next disc tray for playback.
™REPEAT– Selects various repeat modes.
£VOICE (only available in Multi-channel mode)
– Turns on / off clear voice sound effect.
≤MUTE– Mutes or restores the volume.
∞DIM– Turns on / off...

18
EnglishStep 1:Inserting batteries into
the remote control
1
3
2
1Open the battery compartment.
2Insert two batteries type R06 or AA, following
the indications (+-) inside the
compartment.
3Close the cover.
Using the remote control to operate
the system
1Aim the remote control
directly at the remote sensor
(iR) on the front panel.
2Select the source you wish to
control by pressing one of the
source select buttons on the
remote control (for example
TV/AV, TUNER).
3Then select the desired
function (for...

19
English
Step 3: Setting the TV
IMPORTANT!Make sure you have completed all the
necessary connections. (See pages 12~13
“Connecting TV”).
1Adjust SOURCE control until “DISC X”
appears on the display panel (or press
DISC/MEDIA on the remote).
2Turn on the TV and set to the correct video-in
channel.  You should see the blue Philips DVD
background screen on the TV.
➜Usually this channel is between the lowest
and highest channels and may be called
FRONT, A/V IN, or VIDEO. See your TV manual
for more...

20
English
Getting Started
Step 4: Selecting speaker
layout
1
In disc mode, press SYSTEM MENU.
2Use the joystick (1 2 3 4) on the remote to
navigate in the menu.
3Select  icon and press 4.
Move to 
 and press 2.
Move to ‘Speaker Layout’ and press 2.
      
Personal
4Select the layout that most closely resembles
your speakers’ arrangement, then press OK.
➜The speaker output will adjust automatically
to suit the selected speaker layout settings
based on the seating position in the middle.  To
change the...