Philips Mx5800sa User Manual

							11
English
Step 4: Placing the speakers
and subwoofers
For best possible surround sound, all the
speakers should be placed at the same distance
from the listening position.
1Place the left and right front speakers with
subwoofer stands at equal distances from the
TV and at an angle of approximately 45
degrees from the listening position.
2Place the centre speaker above the TV or the
DVD system so that the centre channel’s
sound is localised.
3Place the surround speakers at normal
listening ear level facing each other or
mounted on the wall.
Notes:
–To avoid magnetic interference, do not position
the front speakers too close to your TV.
–Allow adequate ventilation around the DVD
system.
1
33
1
2
Centre speaker
and DVD system
Surround Speaker
(Left)Surround Speaker
(Right)
Connections
1Connect the supplied MW loop antenna to the
MW jack.  Place the MW loop antenna on a
shelf or attach it to a stand or wall.
2Connect the supplied FM antenna to the FM
jack.  Extend the FM antenna and fix its ends to
the wall.
For better FM stereo reception, connect an
external FM antenna (not supplied).
 
MWFM ANTENNA
Notes:
–Adjust the position of the antennas for optimal
reception.
–Position the antennas as far as possible from
your TV, VCR or other radiation source to prevent
unwanted interference.
Step 5: Connecting FM / MW
antennas
FM ANTENNAMW
DIGITAL 
OUT
DIGITAL 
INAUX
INTV
INLINE
OUT AUDIO
VIDEO 
OUTCVBS
S-VIDEO L
R
Pr
Pb
Y
1
2
SPEAKER SYSTEMS (4Ω)
SURROUND CENTER FRONT
L
R
SL
SRC
SUB-WOOFER
➠FM
antenna
fix the claw
into the
slot
Front speaker
with subwoofer
stand (Left)Front speaker
with subwoofer
stand (Right)MW
antenna
 
						

							12
EnglishStep 6:Connecting TV
Connections
IMPORTANT!
–You only need to make one video
connection from the following options,
depending on the capabilities of your TV
system.
–Connect the DVD system directly to
the TV.
Using Composite Video jack
(CVBS)
1Use the composite video cable (yellow) to
connect the DVD system’s CVBS jack to the
video input jack (or labelled as A/V In,  Video In,
Composite or Baseband) on the TV.
2To hear the TV channels through this DVD
system, use the audio cables (white / red) to
connect TV IN (L/R) jacks to the
corresponding AUDIO OUT jacks on the TV.
3Set the P-SCAN switch to ‘OFF.’
Pb
DIGITAL 
OUT
DIGITAL 
INAUX
INTV
INLINE
OUT AUDIO
VIDEO 
OUT
CVBS
S-VIDEO
FM ANTENNA MW
L
RY
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO INCOMPONENT
VIDEO IN
2
1
L
R
SL
SRC
SUB-WOOFER
3
P-SCANON       OFFP-SCANON       OFF
Pb
DIGITAL 
OUT
DIGITAL 
INAUX
INTV
INLINE
OUT AUDIO
VIDEO 
OUT
CVBS
S-VIDEO
FM ANTENNA MW
L
RY
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO INCOMPONENT
VIDEO IN
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO INCOMPONENT
VIDEO IN
2
1
Pr
L
R
SL
SRC
SUB-WOOFER
3
IMPORTANT!
–Component  Video connection
provides higher picture quality.  This
option must be available on your TV.
–The progressive scan video quality is
only possible through Component Video
(Pr Pb Y) output.
Using Component Video jacks
(Pr Pb Y)
1Use the component video cables (red / blue /
green) to connect the DVD system’s Pr Pb Y
jacks to the corresponding Component video
input jacks (or labelled as Pr / Cr Pb / Cb Y or
YUV) on the TV.
2To hear the TV channels through this DVD
system, use the audio cables (white / red) to
connect TV IN (L/R) jacks to the
corresponding AUDIO OUT jacks on the TV.
3If you are using a Progressive Scan TV (TV
must indicate Progressive Scan or ProScan
capability,) set the P-SCAN switch to ‘ON.’
Otherwise, set it to ‘OFF.’
 
						

							13
English
P-SCANON       OFF
Pb
DIGITAL 
OUT
DIGITAL 
INAUX
INTV
INLINE
OUT AUDIO
VIDEO 
OUT
CVBS
S-VIDEO
FM ANTENNA MW
L
RY
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO INCOMPONENT
VIDEO IN
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO INCOMPONENT
VIDEO IN
1
Pr
2
SURROUND CENTER FRONT
L
R
SL
SRC
SUB-WOOFER
3
Connections
IMPORTANT!–If your TV only has a single Antenna In
jack (or labelled as 75 ohm or RF In),
you will need an RF modulator in order
to view the DVD playback on the TV.
See your electronics retailer or contact
Philips for details on RF modulator
availability and operations.
Using an accessory RF modulator
1Use the composite video cable (yellow) to
connect the DVD system’s CVBS jack to the
video input jack on the RF modulator.
2Use the RF coaxial cable (not supplied) to
connect the RF modulator to your TV’s RF
jack.
3Set the P-SCAN switch to ‘OFF.’
IMPORTANT!–S-Video connection provides better
picture quality.  This option must be
available on your TV.
Using S-Video jack
1Use the S-video cable (not supplied) to connect
the DVD system’s S-VIDEO OUT jack to the
S-Video input jack (or labelled as
Y/C or S-VHS) on the TV.
2To hear the TV channels through this DVD
system, use the audio cables (white/red) to
connect TV IN (L/R) jacks to the
corresponding AUDIO OUT jacks on the TV.
3Set the P-SCAN switch to ‘OFF.’
PbDIGITAL 
OUT
DIGITAL 
INAUX
INTV
INLINE
OUT AUDIO
VIDEO 
OUT
CVBS
S-VIDEO
FM ANTENNA MW
L
R
Pr
Y
AUDIO  IN
R             L VIDEO
IN TO TV INT IN
CH3   CH4
1
2
SPEAKER SYSTEMS
SURROUND CENTER FRONT
L
R
SL
SRC
SUB-WOOFER
3
P-SCANON       OFF
RF coaxial cable to TV
Antenna or Cable
TV signalBack of RF Modulator
(example only)
 
						

							14
English
Connections
After everything is connected
properly,
1Set the VOLTAGE SELECTOR to the local
power line voltage.
2Plug in the AC power cord to the power
outlet.
Never make or change any connections with
the power switched on.
On the DVD system,
AUTO INSTALL – PRESS PLAY may
appear on the display panel.  Press ÉÅ  on the
front panel to store all available radio stations
or press Ç to exit (see page 40 “Tuner
Operations”).
               DVD VIDEO DIGITAL SURROUND SYSTEMSTO P PLAY  PAUSE SEATINGTREBLE
BASSSOURCEVOLUME
PROG TUNING CLOCKTIMER SURROUND
SEARCHISC CHANGERDVDDISC
SUR-R
RIGHTCENTRELEFT
SUBSUR-L
PLAYPAUSEAUTO INSTALL - PRESS PLAY
MIC LEVEL MIC
Step 7:Connecting the power
cord
DIGITAL 
OUT
DIGITAL 
INAUX
INTV
INLINE
OUT AUDIO
VIDEO 
OUTCVBS
S-VIDEO FM ANTENNA MW
L
R
~ AC MAINS
~ AC MAINS
Pr
Pb
Y
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO INCOMPONENT
VIDEO IN
VOLTAGE SELECTOR
21
2
P-SCANON       OFF
110V
127V220V
240V
 
						

							15
English
Connections (optional)
Connecting a VCR or
Cable/Satellite Box
DIGITAL 
OUT
DIGITAL 
INAUX
INTV
INLINE
OUT AUDIO
VIDEO 
OUT
CVBS
S-VIDEOFM ANTENNA MW
L
R
Pr
YPb
AUDIO 
OUTPr/CrPb/Cb
Y S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
24
3
1
SPEAKER SYSTEMS (4Ω)
SURROUND CENTER FRONT
L
R
SL
SRCSUB-WOOFER
P-SCANON       OFF
ANT IN
TO TVVCR or
Cable/Satellite Box
Viewing and listening to the playback
1Connect the VCR or Cable / Satellite Box to
the TV as shown.
2Connect the DVD system’s AUX IN (R/L)
jacks to the AUDIO OUT jacks on the VCR or
cable/satellite box.
Before starting operation, press AUX/DI on
the remote to select “AUX” in order to
activate the input source.
Using the VCR for recording DVDs
Some DVDs are copy-protected.  You cannot
record or dub protected discs using a VCR.
3Connect the DVD system’s CVBS jack to the
VIDEO IN jack on the VCR.
4Connect the DVD system’s LINE OUT (R/L)
jacks to the AUDIO IN jacks on the VCR.
This will allow you to make analogue stereo
(two channel, right and left) recordings.
To view DVD playback while recording,
you must connect the DVD system to your TV
using the S-VIDEO (as shown above) or the
Component (Pr Pb Y) video connection.
DIGITAL 
OUT
DIGITAL 
INAUX
INTV
IN AUDIO
MW
L
R
DIGITAL INDIGITAL OUT
2
1
SPEAKER SYSTEMS (4Ω)
SURROUND CENTER FRONT
L
R
SL
SRC
SUB-WOOFER
Connecting digital audio
equipment
(for example)
CD Recorder
Listening to the playback
1Connect the DVD system’s DIGITAL IN jack
to the DIGITAL OUT jack on a digital audio
device.
Before starting operation, press AUX/DI on
the remote to select “DI” in order to activate
the input source.
Recording (digital)
2Connect the DVD system’s DIGITAL OUT
jack to the DIGITAL IN jack on a digital
recording device (DTS-Digital Theatre System
compatible, with a Dolby Digital decoder, for
example).
Before starting operation, set the DIGITAL
OUTPUT according to the audio connection.
(See page 33 “Setting the digital output”).
Notes:
–Some DVDs are copy-protected.  You cannot
record the disc through a VCR or digital recording
device.
–Always refer to the owner’s manual of the other
equipment for complete connection and usage
details.
 
						

							16
English
Functional Overview
* = Press and hold the button for more than two seconds.
1STANDBY ON– Switches to Eco Power standby mode or turns
on the system.
– *Switches to standby mode.
2Disc trays 1~5
3OPEN•CLOSE 0 (DISC1~5)– Opens / Closes the individual disc tray.
4iR SENSOR– Point the remote control towards this sensor.
5Speaker display panel
6System display panel
7TUNING– Switches between frequency tuning and preset
tuning mode.
8PROG (PROGRAM)– DISC: starts programming.
– TUNER: starts *automatic / manual preset
programming.
– CLOCK: selects 12- or 24-hour clock display.
9ÉÅ PLAY•PAUSE– DISC: starts / pauses playback.
– TUNER: *enters Plug & Play mode and / or
starts preset radio station installation (only on
the main unit).
Ç STOP– Exits an operation.
– DISC: stops playback or clears a programme.
– TUNER: *erases a preset radio station.
               DVD VIDEO DIGITAL SURROUND SYSTEM
STO P PLAYPAUSE SEATING
STANDBY- ONiR SENSOR DISC 1
DISC 2
DISC 3
DISC 4
DISC 5DISC 1 DISC 2 DISC 3 DISC 4 DISC 5TREBLE
BASS SOURCEVOLUME
PROG TUNING CLOCKTIMER SURROUND
SEARCH5 DISC CHANGER
OPENCLOSE
DVDDISC
SUR-R
RIGHTCENTRELEFT
SUBSUR-L
MIC LEVELMIC
&^%#@!0987531246$
Main unit and remote control
S  SEARCH  T (PREV/NEXT)– DISC: *searches backward / forward or selects
a track.
– TUNER: *tunes the radio frequency up / down
or selects a preset radio station.
(On the remote, it can only tune the radio
frequency up / down).
– CLOCK: sets the minutes and hours.
0SEATING (only available in Multi-channel
mode)
– Turns on / off the seating control diagram on
the TV.  Use the VOLUME control on the main
unit or joystick on the remote to select the
desired seating position.
!SURROUND (SURR.)– Selects multichannel surround, 3D sound or
stereo mode.
@SOURCE– Selects the relevant active mode : TV/AV, DISC,
TUNER, AUX / DI.
– DISC: toggles between DISC 1~5 (only on the
main unit).
– TUNER: toggles between FM and MW band.
– AUX / DI: toggles between AUX and DI (Digital
Input) mode.
#CLOCK•TIMER– *Enters clock or timer setting mode.
– Shows clock display for a few seconds.
$MIC LEVEL– Adjusts the mixing level when using the
microphone.
MIC
– Plug in the microphone jack.
 
						

							17
English
Functional Overview
Control buttons available on the
remote only
*SYSTEM MENU (DVD mode only)
– Enters or exits system setup menu.
(Joystick 1 2 3 4– Selects movement direction in the menu.
– Use 1 2 to select a preset radio station.
)OK– Confirms a selection.
¡DISC SKIP– Selects next disc tray for playback.
™REPEAT– Selects various repeat modes.
£VOICE (only available in Multi-channel mode)
– Turns on / off clear voice sound effect.
≤MUTE– Mutes or restores the volume.
∞DIM– Turns on / off the dim mode.
§SLEEP– Sets the sleep timer function.
≥SUB +-– Adjusts subwoofer’s sound level.
•TV VOL +-– Adjusts TV volume (Philips TV only).
ªREPEAT A-B– Repeats a specific section on a disc.
ºZOOM– Enlarges a picture on the TV screen.
⁄DISC MENU– Enters or exits disc contents menu.
– For VCD version 2.0 only;
In stop mode, turns on / off playback control
(PBC) mode.
During playback, returns to main menu.
¤SOUND– Selects a sound effect.
‹Numeric Keypad (0-9)– Enters a track / title number of the disc.
– Enters a number of a preset radio station.
›B– Switches to Eco Power standby mode.
– *Switches to standby mode.
* = Press and hold the button for more than two seconds.
TV/AVDISC/
MEDIATUNERAUX/DI
123
456
789
0
REPEAT REPEAT DISC SKIPDISC MENU
PROGRAM SYSTEM MENU
DIM SLEEP SUB TV VOL VOICE MUTE SEATING ZOOM
PREV NEXT
STOP PLAY/PAUSEA-B SURR.
SOUNDVOL
OK
@
‹
!
%
*
(
0
)
8¡
™
£
≤
∞
§
9
ª
•
≥
º
⁄
›
¤
$VOLUME (VOL +-)– Adjusts the volume level.
^BASS / TREBLE– Selects bass or treble sound.  Use the
VOLUME control to select the desired
enhancement level.
&n– Plugging in the headphones jack.  The speakers
output will be cancelled.
 
						

							18
EnglishStep 1:Inserting batteries into
the remote control
1
3
2
1Open the battery compartment.
2Insert two batteries type R06 or AA, following
the indications (+-) inside the
compartment.
3Close the cover.
Using the remote control to operate
the system
1Aim the remote control
directly at the remote sensor
(iR) on the front panel.
2Select the source you wish to
control by pressing one of the
source select buttons on the
remote control (for example
TV/AV, TUNER).
3Then select the desired
function (for example ÉÅ,
S,
  T).
CAUTION!–Remove batteries if they are
exhausted or if the remote is not to be
used for a long time.
–Do not use old and new or different
types of batteries in combination.
–Batteries contain chemical substances,
so they should be disposed of properly.
Step 2: Setting the clock
The clock can be set in either 12-hour or
24-hour mode (12:00 AM or 00:00 for
example).
  
CLOCKTIMER
CLOCKTIMER
SEARCH
PROG
CLOCKTIMER
2
3
5
4
6
SELECT CLOCK OR TIMER
CLOCK
01:38 PM
13:38
13:38
1Press STANDBY ON to switch on the DVD
system.
2Press and hold CLOCK•TIMER until
SELECT CLOCK OR TIMER appears.
3Press T (if necessary) to change the display
to CLOCK, then press CLOCK•TIMER
again to confirm.
4Press S / T to set the minutes and
hours.  To increase the speed, hold down
S / T.
➜The changes in minutes will roll over to the
hours.
5Press PROG to change between 12-hour and
24-hour clock mode.
6Press CLOCK•TIMER again to store the
setting.
➜The clock will start working.
To view the clock time in any active
mode
Press CLOCK•TIMER.
➜The clock will display for a few seconds.
Notes:
–If the DVD system is disconnected from the
power supply, it will erase the clock setting.
–If you do not press any buttons within 90
seconds, the system will exit clock setting mode.
STANDBY- ONiR SENSOR 
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5DISC 1 DISC 2 DISC 3OPENCLOSE
123
456
789
0
REPEAT REPEAT DISC SKIPDISC MENU
PROGRAM SYSTEM MENU
SEATING ZOOM
PREV NEXT
SURR.SOUNDVOL
OK
TV/AVDISC/
MEDIATUNERAUX/DI
STOP PLAY/PAUSE
buttons on
front panelDVD system’s
display panel
Getting Started
 
						

							19
English
Step 3: Setting the TV
IMPORTANT!Make sure you have completed all the
necessary connections. (See pages 12~13
“Connecting TV”).
1Adjust SOURCE control until “DISC X”
appears on the display panel (or press
DISC/MEDIA on the remote).
2Turn on the TV and set to the correct video-in
channel.  You should see the blue Philips DVD
background screen on the TV.
➜Usually this channel is between the lowest
and highest channels and may be called
FRONT, A/V IN, or VIDEO. See your TV manual
for more details.
➜Or, you may go to channel 1 on your TV,
then press the Channel down button
repeatedly until you see the Video In channel.
➜Or, the TV remote control may have a
button or switch that chooses different video
modes.
➜Or, set the TV to channel 3 or 4 if you are
using an RF modulator.
Changing the NTSC / PAL setting via
the remote control
TV/AVDISC/
MEDIATUNERAUX/DI
456 123
12,
1Press DISC / MEDIA on the remote to enter
disc mode.
➜Make sure no MP3 disc is in disc tray 1.
➜Wait until the system finishes reading the
discs before proceeding to next step.
If playback begins, press Ç to stop playback.
2Press and hold DISC/MEDIA on the remote
until “PAL” or “NTSC” appears on the display
panel.
➜To change the setting, repeat step 
2.
Selecting the colour system that
corresponds to your TV
This DVD system is compatible with both NTSC
and PAL.  In order for a DVD to play on this
DVD system, the colour system of the DVD, the
TV and the DVD system should match.
1In disc mode, stop playback and press
SYSTEM MENU.
2Use the joystick (1 2 3 4) on the remote to
navigate in the menu.
3Select  icon and press 4.
Move to 
 and press 2.
Move to ‘TV System’ and press 2.
Auto – Select this if the connected TV is
compatible with both NTSC and PAL (multi-
system).  The output format will be in
accordance with the video signal of the disc.
NTSC – Select this if the connected TV is
NTSC system. It will change the video signal of
a PAL disc (VCD only) and output to NTSC
format.  Set the ‘Black level shift’ to ‘
On’ in
order to improve the colour contrast and
picture when you play an NTSC-compatible
DVD.
PAL – Select this if the connected TV is PAL
system. It will change the video signal of an
NTSC disc and output to PAL format.
4Select an item and press OK.
To remove the menuPress SYSTEM MENU.
TV Shape
Black Level shift
Video shift1en
1enst 1
Personal color Color settings
TV System
Pal
NTSC
AutoDigital Crystal Clear
DISC MENU SYSTEM MENU
SEATING ZOOM
PREV NEXT
STOP PLAY/PAUSE
OK
23,
4
1
Getting Started
➠
 
						

							20
English
Getting Started
Step 4: Selecting speaker
layout
1
In disc mode, press SYSTEM MENU.
2Use the joystick (1 2 3 4) on the remote to
navigate in the menu.
3Select  icon and press 4.
Move to 
 and press 2.
Move to ‘Speaker Layout’ and press 2.
      
Personal
4Select the layout that most closely resembles
your speakers’ arrangement, then press OK.
➜The speaker output will adjust automatically
to suit the selected speaker layout settings
based on the seating position in the middle.  To
change the seating position, see “Changing
seating control position”.
➜If you choose ‘Personal’, the speaker output
will follow the settings in the ‘Speakers‘ menu
(see next page “Setting the speakers’
channels”).
To remove the menuPress SYSTEM MENU.
Changing seating control position
Normally, the best sound spot and the ideal
setting position is in the middle of the room.
With this ‘SEATING’ feature, it allows you to
select the current seating position in the room
and the speaker setting will automatically be
adjusted for optimum performance.
     
DISC MENU SYSTEM MENU
SEATINGZOOM
PREV NEXT
VOL
7890SOUNDSURR.
3
1
24,
1Press SURR. (or SURROUND on the front
panel) repeatedly to select ‘Multi-channel’.
2Press SEATING.
➜The seating control diagram which
represents your current speaker layout
appears on the TV screen.  To change the
speaker layout, see “Selecting speaker layout”.
3Use the joystick (1 2 3 4) on the remote
(or VOLUME control on the front panel) to
select your current seating position.
➜During playback, you can hear the changing
of sound effect when you change the seating
position.
➜If you do not press any buttons within five
seconds, the seating control diagram will exit
from the TV and the system will execute the
last selected seating position.
4If you want to turn off the seating feature,
press SEATING again.
➜“PERSONAL SETTING” appears and
the system will revert to the personal speaker
settings.
1en1enst 1
Digital output
Analog output
Night mode
Karaoke vocal
SpeakersAll
Speaker layout
PCM output
Multi-channelOffOffSquareSettings...48 kHz
➠
DISC MENU SYSTEM MENU
SEATING ZOOM
PREV NEXT
STOP PLAY/PAUSEOK
23,
4
1