Philips Hts3366 User Manual

							
English
EN     21
Get started
Change speakers settings
Ideally the distance between listening position 
and all the speakers should be the same. If not, 
change the speaker settings based on their 
distance from the listening position in order to 
obtain the best possible surround sound.
1 Press  DISC.
2 Press  OPTIONS .
3 Press V to select  [ Audio Setup ]  in 
the menu, then press  B.
Audio Setup
Speakers Volume
Speakers Delay
HDMI Audio
CD Upsampling
Audio Sync
You cannot access speaker setup 
options if this Home Theatre unit is not 
in a complete stop mode. In such case, 
press  x twice.
To adjust the speakers volume level
4 Select  [ Speakers Volume ]  in the menu, 
then press  B.
Speakers Level Setup
Front Left
Front Right
Center
Subwoofer
Rear Left
Rear Right 0dB
0dB
0dB
0dB
0dB
0dB
•
5 Press 
b B to adjust the volume level, then 
press  OK.
  The test tone is emitted from the 
speaker which you are adjusting.
Repeat the above setting for other 
speakers until all the speakers output 
level sounds equally balance.
To set the output delay time (centre and rear 
speakers only) 
6 Select  [ Speakers Delay ]  in the menu, 
then press  B.
Speakers Distance Setup
Center
Rear Left
Rear Right 0ms
0ms
0ms
7 Press 
b B to set the delay time, then 
press  OK.
Repeat the above setting for other 
speakers until the sound output from 
different speakers reach the listening 
position at the same time.  
    Tips
Set longer delay time if the centre or rear speaker s 
are closer to the listening position than the front 
speaker s.  
1ms set ting for ever y 30cm distance between the 
speaker and the listening position.•
•
8 To exit the menu, press  OPTIONS.
•
•
1
_hts 3 366_93-9 8_en g4_fin al8 08.i n 21   2 11_hts3366_93-98_eng4_final808.in21   212008-0 2-2 2   1 0:1 7:4 2 A M2008-02-22   10:17:42 AM
 
						

							
22      EN
Activate EasyLink control
This feature is only applicable if this unit is 
connected to HDMI CEC compliant TV/device.  
It enables all the linked devices response or 
react to certain commands simultaneously with 
one touch control.
1 Turn on the HDMI CEC operations on 
your TV and other connected devices. See 
TVs/devices manual for details.
2 You can now enjoy the EasyLink controls.
One touch play [ Auto Wake-up TV ]
When you press PLAY to turn on this unit 
and start disc play (if a video disc is found 
in the disc compartment), it turns on your 
TV automatically and switches to the 
correct viewing channel.
One touch power off [ System Standby ]
This unit responses to standby command 
from other HDMI CEC compliant TV/
devices. For example, if you turn off the 
TV, this unit automatically turns off to 
standby even during playback.
To power off using this unit’s remote 
control, you have to press and hold  2.
•
One touch audio input switching [ System 
Audio Control ]
This unit is able to render the audio signals 
from the active source. It switches 
automatically to the corresponding audio 
input and output the sound from its 
speakers system.
Before you can enjoy this function, you 
have to map the audio inputs to the 
connected devices. 
You can use any HDMI CEC T V/device 
remote control to adjust the volume.
•
•
 Note
To enable one touch play func tion, a video disc must 
be placed in the disc compar tment before operation.
Philips does not guarantee 100% interoperability 
with all HDMI CEC compliant devices. •
•
Map the audio inputs to the 
connected devices
1 Press 
DISC.
2 Press  OPTIONS .
3 Press V to select  [ Video Setup ]  in the 
menu, then press  B.
4 Select  [ HDMI Setup ]  > [ EasyLink ]
, then 
press  OK.
EasyLink
Auto Wake-up TV
System Standby
System Audio Control
HDMI Input Mapping
 
[ Auto Wake-up TV ]  and [ System 
Standby ]  functions are turned on by 
default in the factory.  
5 Select  [ System Audio Control ]  > [ On ] , 
then press  OK.
6 Select  [ HDMI Input Mapping ] , then press 
OK .
7 Select  [ OK ]  in the menu, then press  OK 
to start scanning of devices.
  Once complete, audio input mapping 
menu is displayed.
8 Select an input to map (e.g. AUX1, AUX2), 
then press  B. 
•
1
_hts 3 366_93-9 8_en g4_fin al8 08.i n 22   2 21_hts3366_93-98_eng4_final808.in22   222008-0 2-2 2   1 0:1 7:4 3 A M2008-02-22   10:17:43 AM
 
						

							
English
EN     23
Get started
9 Select the correct device that connected 
to this audio input, then press  OK.
Repeat steps 8~9 to map other 
connected devices.
10  To exit the menu, press  OPTIONS.
•
Select a play source
On the main unit
1 Press 
SOURCE  button repeatedly to 
select:  DISC >  FM   > AM/MW >  AUX1  >  
AUX2 >  DI (DIGITAL IN)  >  MP3 LINK  >
 
DISC  ...
On the remote control
Press  DISC to switch to DISC mode.
Press  USB to switch to USB mode.
Press  RADIO  to switch to FM or AM/MW 
band.
Press  AUX / MP3 LINK  repeatedly to listen 
to the audio output from the external 
device. 
Display Device connected to
AUX1 AUDIO IN-AUX1 sockets.
AUX2 AUDIO IN-AUX2 sockets.
DI DIGITAL IN-COAXIAL 
socket.
MP3 LINK MP3 LINK socket.
•
•
•
•
1_hts 3 366_93-9 8_en g4_fin al8 08.i n 23   2 31_hts3366_93-98_eng4_final808.in23   232008-0 2-2 2   1 0:1 7:4 3 A M2008-02-22   10:17:43 AM
 
						

							
24      EN
5 Play
Play from disc
Playable discs
DVD Video
Region 3 (Asia Paci fi c, 
Ta i w a n ,  K o r e a)
Region 4 (Australia, New 
Zealand)
Region 6 (China)
•
•
•
DVD±RW 
(DVD Rewritable)
DVD±R 
(DVD Recordable)
DVD+R DL (DVD+R Double 
Layer)
ReWritable
CD-RW (CD-Rewritable)
MP3/WMA/JPEG/DivX
•
Recordable
CD-R (CD-Recordable)
MP3/WMA/JPEG/DivX
•
Audio CD 
(Compact Disc Digital Audio)
Video CD
For mats 1.0, 1.1, 2.0
•
Super Video CD
 Note
DVDs and DVD player s are designed with regional 
restric tions. Before playing a disc, ensure the disc is 
for the same region zone as your player (indicated 
on its rear).•
Play a disc
  Caution!
Never place any objec ts other than discs into the 
disc compar tment.
Never look into the laser beam inside the Home 
Theatre unit.•
•
1 Press  Z to open the disc compartment.
2 Insert a disc with its label facing up.
For double-sided disc, load the side to 
play faces up.
3 Press  Z to close the disc compartment 
and start disc play.
To view disc play, turn on the TV to 
the correct viewing channel for this 
DVD Home Theatre unit.
4 To stop disc play, press  x.
   Tips
If the password entr y menu is displayed, you have to 
key in the 6 -digit password before it can be played.  
Screen saver displays automatically if the disc play 
is stopped for about 5 minutes. To wake up from 
screen saver, press  DISC.  
This unit automatically switches to standby mode if 
you do not press any but tons within 15 minutes af ter 
a disc has stopped playing.•
•
•
•
•
1 _hts 3 366_93-9 8_en g4_fin al8 08.i n 24   2 41_hts3366_93-98_eng4_final808.in24   242008-0 2-2 2   1 0:1 7:4 3 A M2008-02-22   10:17:43 AM
 
						

							
English
EN     25
Play
Play video
 Note
For video disc, playback always resumes from the 
point where it was last stopped. To star t playback 
from the beginning, press  í while the message 
‘Playback from the beginning, press  í key’ is 
displayed.•
Control a title
1   Play a title.
2 Use the remote control to control the title. 
Button Action
Pause/ resume play.
Stop play.
Jump to the next title/chapter.
Return to the beginning of the 
current title/chapter or jump to 
the previous title/chapter.
m  M Search backward/ forward.
To change search speed, 
press this button repeatedly.
•
v V Slow motion reverse/ forward 
play.
To change play speed, press 
this but ton repeatedly.
For VCD, only for ward play 
is possible.
•
•
Change video play 
1   Play a title.
2 Use the remote control to change the 
video play. 
Button Action
Change audio language.
Only applicable to discs 
with multiple audio 
language or channel.
•
Change subtitle language.
Only applicable to discs 
with multiple subtitle 
language.
•
Toggle through various repeat/
shuf
fl e play mode; or turn off 
repeat mode (RPT OFF’).
Repeat options var y 
depending on the disc type.  
For VCDs, repeat play is 
only possible if the PBC 
mode is turned off.
•
•
Zoom in/out.
To pan through the zoomed 
image, press the cursor 
buttons.
•
Display current play status. 
You can change the video 
play options here without 
interrupting disc play. 
•
1
_hts 3 366_93-9 8_en g4_fin al8 08.i n 25   2 51_hts3366_93-98_eng4_final808.in25   252008-0 2-2 2   1 0:1 7:4 4 A M2008-02-22   10:17:44 AM
 
						

							
26      EN
Access DVD menu
1 Press  DISC to access disc main menu.
2 Select a play option, then press  OK.
In some menus, press  number buttons 
to input your selection.
To return to the title menu during 
playback, press  MENU.
Access VCD menu or preview menu
The PBC (Playback Control) for VCD is turned 
on by default in the factory. When you load in a 
VCD, the contents menu is displayed. 
1 Press vV to select a play option, then 
press  OK to start play.
If PBC is off, it skips the menu and start 
play from the  fi rst title.
During playback, you can press  MENU 
to return to the menu (if the PBC 
mode is on).
2 To preview the contents of the disc, press 
DISC .
To exit the menu, press  DISC.
•
•
•
•
•
Select Digest Type:
Track Digest
Disc Interval
Track Interval
 
[ Track Digest ]
It plays the 
fi rst few seconds of each track 
in a disc.
[ Disc Interval ]
It divides the total disc time by six and 
plays the  fi rst few seconds of these 
intervals.
[ Track Interval ]
It divides the current track by six and plays 
the  fi rst few seconds of these intervals. 
This option is not available in stop 
mode.
3 Select a preview play option, then press 
OK .
   Tips
The default set ting for PBC is on. To change the 
default set ting, see chapter ‘Adjust set tings’ - 
[ Preferences ]  > [ PBC ]  for details.•
•
1_hts 3 366_93-9 8_en g4_fin al8 08.i n 26   2 61_hts3366_93-98_eng4_final808.in26   262008-0 2-2 2   1 0:1 7:4 4 A M2008-02-22   10:17:44 AM
 
						

							
English
EN     27
Play
Sync audio output with video play
If the video play is slower than the audio output 
(sound does not match with the pictures), you 
can delay the audio output to match the video.
1 Press and hold  AUDIO SYNC  until 
‘AUDIO SYNC XXX’ is displayed.
‘XXX’ denotes the delay time.
2 Within  fi ve seconds, press  VOL +- to 
set the delay time for audio output.
 Note
If the volume control is not used within  fi ve seconds, 
it resumes nor mal volume control func tion. •
Quick skip play to a speci fi c time
1 During playback, press  INFO.
   The disc status menu is displayed.
2 Select the current elapsed playing time in 
the menu, then press  OK.
[ TT Time ]  (title time) 
[ CH Time ]  (chapter time) 
[ Disc Time ]  (disc time) 
[ Track Time ]  (track time) 
•
•
•
•
•
3 Press the 
number buttons  to change the 
time where you want to skip to, then press 
OK .
Repeat play a speci fi c section
1 During playback, press  INFO.
   The disc status menu is displayed.
2 Select  [ Repeat ]  in the menu, then press 
B .
3 Move to  [  A-B ] in the menu, then 
press  OK to set the start point.
4 Press  OK again to set the end point.
   Repeat play starts.
5 To cancel repeat play, select  [ 
Repeat 
Off  ]
 and press  OK.
 Note
The mar ked sec tion for repeat play is only possible 
within a track /title.•
View DVD play from different camera 
angles 
1 During playback, press  INFO.
   The disc status menu is displayed.
2 Select  [ Angle ]  in the menu, then press 
OK .
3 Press the  number buttons  to select an 
angle, then press  OK.
 Note
Only applicable to discs contain sequences recorded 
from dif ferent camera angles.•
1_hts 3 366_93-9 8_en g4_fin al8 08.i n 27   2 71_hts3366_93-98_eng4_final808.in27   272008-0 2-2 2   1 0:1 7:4 4 A M2008-02-22   10:17:44 AM
 
						

							
28      EN
Play DivX® video 
DivX video is a digital media format that retains 
high quality despite a high rate of compression.  
This unit is DivX® Certi fi ed so that you can 
enjoy DivX video.
1 Insert a disc or USB that contains the DivX 
videos.
2 Press  DISC or USB .
   A contents menu is displayed.
3 Select a title to play, then press  u.
4 Use the remote control to control the 
title. 
Button Action
Change subtitle language.
Change audio language/track.
Stop play.
For DivX Ultra video, press 
this but ton again to display 
the contents menu.
•
Display DivX Ultra video 
information.
 Note
Only those DivX videos that were rented or 
purchased using the DivX registration code of this 
unit can be played (see chapter ‘Adjust set tings’ > 
[ General Setup ]
 > [ DivX(R) VOD Code ]  for 
details).
If the subtitle does not appear correc tly, change the 
subtitle language (see chapter ‘Adjust set tings’ - 
[ Preferences ]  > [ DivX Subtitle ]  for details).
The subtitle can only be displayed up to an average 
of 45 charac ter s.
This unit can play DivX video  fi les that are up to 4GB 
in size.•
•
•
•
Play music
 Note
For some commercial audio disc, playback may 
resume from the point where it was last stopped. 
To star t play from  fi rst track, press  í.•
Control a track
1 Play a track.
2 Use the remote control to control the 
track. 
Button Action
Pause/ resume play.
Stop play.
Jump to the next track.
Return to the beginning of the 
current track or jump to the 
previous track.
Direct input the track number.
m  M Search backward/ forward.
To change search speed, 
press this but ton repeatedly.
•
Toggle through various repeat/
shuf
fl e play mode; or turn off 
repeat mode.
Repeat options var y 
depending on the disc type.  
•
1
_hts 3 366_93-9 8_en g4_fin al8 08.i n 28   2 81_hts3366_93-98_eng4_final808.in28   282008-0 2-2 2   1 0:1 7:4 5 A M2008-02-22   10:17:45 AM
 
						

							
English
EN     29
Play
Play MP3/WMA music 
MP3/WMA is a type of highly compressed 
audio  fi le ( fi les with .mp3 or .wma extensions).
1 Insert a disc or USB that contains the MP3/
WMA music.
2 Press  DISC or USB .
   A contents menu is displayed.
3 Select a folder, then press  OK.
4 Select a track to play, then press  u.
To return to the main menu, press  v 
until ‘Previous’ folder is selected, then 
press  OK.
 Note
For CDs recorded in multiple sessions, only the  fi rst 
session is played.
This unit does not suppor t MP3PRO audio for mat.
If any special charac ter s are present in the MP3 track 
name (ID3) or album name, it might not be displayed 
correc tly on the screen because these charac ter s are 
not suppor ted.  
Some WMA is protec ted by Digital Rights 
Management (DRM), it cannot be played on this unit.
Folders/ fi les exceed the suppor ted limit of this unit 
will not be displayed or played.•
•
•
•
•
    Tips
To display the data disc contents without folder s, see 
chapter ‘Adjust set tings’ -  [ Preferences ] > 
[ MP3/JPEG Nav ]  for details.•
•
Play photo
Play photos as slideshow
This unit can play JPEG photos ( fi les with .jpeg 
or .jpg extensions).
1 Insert a disc or USB that contains the JPEG 
photos.
2 Press  DISC or USB .
   For a Kodak disc, the slideshow begins 
automatically.
   For a JPEG disc, the photo menu is 
displayed.  
3 Select the folder/album you want to play.
To preview the photos in the folder/
album, press  INFO.
To go to previous or next screen 
display, press  í / ë .
To select a photo, press the cursor 
buttons.
To display the selected photo only, 
press  OK.
4 Press  u to start slideshow play.
To return to the menu, press  MENU.
•
•
•
•
•
1
_hts 3 366_93-9 8_en g4_fin al8 08.i n 29   2 91_hts3366_93-98_eng4_final808.in29   292008-0 2-2 2   1 0:1 7:4 5 A M2008-02-22   10:17:45 AM
 
						

							
30      EN
 Note
It may require longer time to display the disc content 
on the T V due to the large number of songs/photos 
compiled onto one disc.
If the JPEG photo is not recorded with an ‘exif ’ 
type  fi le, the ac tual thumbnail pic ture will not be 
shown on the display. It will be replaced with a ‘blue 
mountain’ thumbnail pic ture.
This unit can only display digital camera pic tures 
according to the JPEG -E XIF for mat, typically used by 
almost all digital cameras. It cannot display Motion 
JPEG and pic tures in for mats other than JPEG , or 
sound clips associated with pic tures.
Folders/ fi les exceed the suppor ted limit of this unit 
will not be displayed or played.•
•
•
•
Control photo play
1 Play photo slideshow.
2 Use the remote control to control the 
photo. 
Button Action
b Skip to the previous photo.
B Skip to the next photo.
v Rotate the photo clockwise.
V Rotate the photo anti-
clockwise.
Zoom in/ out.
Play will pause while in 
zoom mode.
•
Stop play.
Play musical slideshow
Play MP3/WMA music 
fi les and JPEG photo 
fi  les simultaneously to create musical slideshow.  
The MP3/WMA and JPEG  fi les must be stored 
on the same disc or USB device.
1 Play MP3/WMA music. 
2 While music play, navigate to the photo 
folder/album and press  u to start 
slideshow play.
   Slideshow begins and continues till the 
end of the photo folder or album.  
   Audio continues to play till the end of 
the disc.
To return to the menu, press  MENU.
3 To stop slideshow play, press  x.
4 To stop music play, press  x again.
•
1
_hts 3 366_93-9 8_en g4_fin al8 08.i n 30   3 01_hts3366_93-98_eng4_final808.in30   302008-0 2-2 2   1 0:1 7:4 5 A M2008-02-22   10:17:45 AM