Philips 46pfl9715k User Manual
Have a look at the manual Philips 46pfl9715k User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 619 Philips manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4 4.1 Setup Picture and sound Smart settings If you select a Smart setting in the ADJUST menu, you can again change the settings of the selected Smart setting with the Picture and sound settings in Setup. The Smart setting remembers your changes. Reset a Smart setting To reset a Smart setting to its original values, select the Smart setting you want to reset in the ADJUST menu. Then press h > Setup > TV settings , select Reset, press OK and confirm. Read more about using Smart picture and sound settings in Help > Use your TV > Watch TV > Smart picture and sound settings . Picture In the Picture menu, you can adjust all picture settings individually. To open the Picture settings , press h > Setup > TV settings > Picture . • Contrast Sets the contrast level of the picture. • Brightness Sets the brightness level of the picture. • Colour Sets the level of colour saturation. • Hue If NTSC is broadcast, hue compensates the colour variations. • Sharpness Sets the level of sharpness of fine detail. • Noise reduction Filters out and reduces the image noise in the picture. • Tint Sets the colours to Normal, Warm (reddish) or Cool (bluish). Select Custom to set up your own personal settings in the Custom menu. • Custom tint Use the slider bar to set the colour temperature of the picture. • Perfect Pixel HD Controls the advanced settings of the Perfect Pixel HD Engine. — Perfect Natural Motion removes motion judder and reproduces smooth movement, especially in movies. — LED 400 Hz Clear LCD gives a superior motion sharpness, better black level, high contrast with a flicker -free, quiet image and a larger viewing angle. — Super resolution enables superior sharpness, especially on lines and contours in the picture. — Perfect contrast sets the level at which the TV automatically enhances the details in the dark, middle and light areas of the picture. — Dynamic backlight sets the level at which power consumption can be reduced by dimming the brightness intensity of the screen. Choose for the best power consumption or for the picture with the best brightness intensity. — MPEG artefact reduction smooths the digital transitions in the picture. — Colour enhancement makes the colours more vivid and improves the resolution of details in bright colours. — Gamma is a non-linear setting for picture luminance and contrast. Use the slider bar to set a higher or lower gamma value. • PC mode Sets the TV to the ideal pre-defined computer setting if a computer has been connected. • Light sensor Adjusts the picture and Ambilight settings automatically to the lighting conditions of the room. • Picture format Read Help > Use your TV > Watch TV > Picture format . • Screen edges Slightly enlarge the picture to hide distorted edges. • Picture shift Move the picture up / down or left / right with the cursor keys. Sound In the Sound menu, you can adjust all sound settings individually. To open Sound settings , press h > Setup > TV settings > Sound . • Bass Sets the level of low tones in the sound. • Treble Sets the level of high tones in the sound. • Surround Sets the surround sound effect from internal speakers. • Headphones volume Sets the volume for the headphone connection of the TV. • Auto volume levelling Reduces sudden volume differences like at the beginning of adverts or when switching from one channel to another. • Balance Sets the balance of the left and right speakers to best fit your listening position. Eco settings Eco settings bundle the TV settings that help the environment. While you are watching TV channels, press the Green key to open Eco settings . Active settings are marked with a ê. Press again to close. Energy saving This Smart picture setting sets the picture, together with Ambilight, in the most ideal energy conscious setting. To switch on, select Energy saving in Eco settings and press OK. To switch off Energy saving, select another Smart picture setting. Screen off If you only listen to music, you can switch off the TV screen to save energy. Select Screen off and press OK. To switch the screen back on, press any key on the remote control. Light sensor The built -in light sensor automatically adjusts the picture, together with Ambilight, to the lighting conditions of the room. To switch on, select Light sensor and press OK. To switch off, press OK again. Setup / Picture and sound41
Auto switch off If no keys on the TV remote control were pressed during a 4 - hour period, the TV switches off automatically to save energy. You can switch off this Auto switch off . If you use the TV as a monitor or use a digital receiver to watch TV (a set top box - STB) and you do not use the remote control of the TV, switch off the automatic switch off. 42Setup / Picture and sound
4.2Ambilight Placement For the best Ambilight effect : • Dim the lighting conditions in the room and position the TV up to 25 cm away from the wall. • Adjust Ambilight according to the colour of your wall at home in the Wall colour setting. • To prevent poor infrared remote control reception, position your devices out of sight of Ambilight. Adjust To open the Adjust menu, press tADJUST . To close, press t again. Switch Ambilight on or off In the Adjust menu, select Ambilight and press OK. Switch Ambilight On or Off. You can also press Ambilight on the TV. Ambilight dynamic In the Adjust menu, select Ambilight dynamic and press OK. Adjust the speed at which Ambilight responds to onscreen images. Read more about other Ambilight settings in Help > Setup > Ambilight > Settings . Settings More Ambilight settings are available in the Ambilight settings menu in Setup. To change these settings, press h and select Setup > TV settings > Ambilight. Ambilight brightness To set the Ambilight brightness, select Ambilight brightness and press OK. Adjust the light output of Ambilight. Ambilight colour To set the Ambilight colour, select Ambilight colour and press OK . Select Dynamic , if Ambilight should respond to onscreen images or select one of the fixed colours. Select Custom if you want to set a specific fixed colour. Custom colour To set a Ambilight colour of your own, select Custom in the Ambilight Colour menu. With Custom selected, you can open the Custom colour menu. Select Palette to choose your own colour. Ambilight Custom colour is a fixed (non-dynamic) colour setting. Separation To set the difference in colour level between the lights on each side of the TV, select Separation. Separation Off gives a dynamic but uniform Ambilight colour. TV switch off To set Ambilight to fade out and switch off a few seconds after you have switched off the TV, select TV switch off. Allow Ambilight to fade out and switch off completely before you switch the TV back on again. Lounge light mood Read more about Lounge light mood in Help > Setup > Ambilight > Lounge light mood . Scenea lounge light To always switch off Ambilight when Scenea is switched on, select Scenea lounge light and select Off. Wall colour The colour of the wall behind your TV can influence the colour effect of Ambilight. To correct this influence, select Wall colour and select a colour that matches the wall colour. Ambilight will correct its colours to mix best with the colour of the wall behind the TV. Lounge light When the TV is on standby, you can switch Ambilight on and create a Lounge light effect in your room. To switch Ambilight on while the TV is on standby, press Ambilight on the TV. To change the Lounge light colour scheme, press Ambilight on the TV again. To switch off Lounge light, press and hold Ambilight on the TV for 3 seconds. You can also set up the colour scheme in the Setup menu. With the TV switched on, press h and select Setup. Select TV settings > Ambilight > Lounge light mood . Select the colour scheme with which Lounge light will start up. Setup / Ambilight43
4.3Channels Reorder and rename You can reorder and rename channels in the Channel list. To reorder or rename a channel, read Help > Use your TV > Watch TV > Channel list . Update channels The TV puts all installed channels in the Channel list. If you receive digital channels, you can set the TV to automatically update the list with new channels. You can also start an update of the Channel list yourself. Automatic channel update Once a day, at 6 AM, the TV updates the channels and stores new channels. Empty channels are removed. For new or removed channels, a message is shown at TV start up. The TV must be in standby to automatically update channels. To switch off the message at start up, press h > Setup > Channel settings and press OK. Select Channel installation > Channel update message and select Off. To switch off the automatic channel update, press h > Setup > Channel settings and press OK. Select Channel installation > Automatic channel update and select Off. Start an update To start an update yourself, press h > Setup > Search for channels and press OK. Select Update channels and press OK. Press Start. The update can take a few minutes. Follow the instructions on screen. Reinstall channels Reinstall channels To reinstall only the channels, press h > Setup > Search for channels > Reinstall channels and press OK. Select DVB -T or DVB -C . The channel search can take a few minutes. Follow the instructions on screen. Full installation To redo a full TV installation, press h > Setup > TV settings > Reinstall TV and press OK. The installation can take a few minutes. Follow the instructions on screen. You can reorder and rename channels in the Channel list. Channel list copy Channel list copy is intended for dealers and expert users. With Channel list copy, you can copy the channels installed on one TV onto another Philips TV of the same range. With Channel list copy, you avoid the time-consuming channel search and you can offer a predefined channel list setup. The small file you copy fits every USB memory device. Conditions • Both TVs are from the same year range. • Both TVs have the same product type suffix for DVB (H, K, M, T or D/00) in their type number and have the TV installed for the same country. • Both TVs have the same hardware type. Check the hardware type on the TV type plate on the back of the TV. Typically noted as Q . . . LA • Both TVs have compatible software versions. When you upload, an on -screen message will warn you if software versions are not compatible. Copy a Channel list 1 Switch on the TV which has its channels installed. Plug in a USB memory device. 2 Press h > Setup > TV settings > Preferences > Channel list copy > Copy to USB and press OK. To copy the Channel list from this TV, you might be asked to enter the TV PIN code you entered during the installation. 3 When copying is done, unplug the USB memory device. Now you can upload the copied Channel list onto another Philips TV. Upload a Channel list To a TV thats not yet installed 1 Plug in the power plug to start the installation and select language and country. You can skip Search for channels. Finish the installation. 2 Plug in the USB memory device that holds the Channel list of the other TV. 3 To start the Channel list upload, press h > Setup > TV settings > Preferences > Channel list copy > Copy to TV and press OK. You might be asked to enter the TV PIN code of this TV. 4 The TV notifies if the Channel list is copied to the TV successfully. Unplug the USB memory device. To an already installed TV 1 Verify the country setting of the TV. (To verify this setting, press h > Setup > Search for channels > Reinstall channels and press OK. Press È (Back) and later Cancel to leave the Search for channels.) If the country is correct continue with step 2 hereunder. If the country is not correct, you need to start a reinstallation. To start the reinstallation, press h > Setup > TV settings > Reinstall TV and press OK. Select the correct country and skip the Search for channels. Finish the installation. When done, return to step 2. 2 Plug in the USB memory device that holds the Channel list of the other TV. 3 To start the Channel list upload, press h > Setup > TV settings > Preferences > Channel list copy > Copy to TV and press OK. You might be asked to enter the TV PIN code of this TV. 4 The TV notifies if the Channel list is copied to the TV successfully. Unplug the USB memory device. DVB- T or DVB- C If both DVB-T and DVB-C reception is available in your country and if this TV is ready to receive DVB-T and DVB-C for your country, you will have selected one or the other during the channel installation. If you want to change the DVB setting to start a new channel installation, press h > Setup > Channel settings and press OK. Select Channel installation > Antenna or Cable DVB and press OK . Select the DVB setting you want. 44Setup / Channels
DVB -C channel installation For ease of use, all DVB-C settings are set to automatic. If your DVB-C provider gave you specific DVB-C values, like a symbol rate or a frequency, enter these values when the TV asks for them during installation. DVB -T + DVB -C You can set up your TV for DVB-T and DVB-C. Install one system followed by the other. When both installations are complete, the Channel list will show both DVB-T and DVB-C channels. Reception quality If you receive digital channels, you can check the quality and signal strength of a channel. If you use an antenna, you can reposition the antenna to try and improve the reception. To check the reception quality of a digital channel, switch to the channel and press h > Setup > Channel settings and press OK . Select Channel installation > Digital : reception test and press OK. The digital frequency is shown for this channel. If the reception is poor, you can reposition your antenna. To check the signal quality of this frequency again, select Search and press OK. To enter a specific digital frequency yourself, select the frequency, position the arrows on a number with x and w and change the number with u and v. To check the frequency, select Search and press OK. If you use DVB-C to receive channels, the options Symbol rate mode and Symbol rate are available. For Symbol rate mode, select Automatic , unless your cable provider gave you a specific symbol rate value. To enter the symbol rate value, use the number keys. Manual installation — Analogue Analogue TV channels can be manually tuned in channel by channel. To install analogue channels manually, press h > Setup > Channel settings and press OK. Select Channel installation > Analogue : manual installation and press OK. 1 System To set up the TV system, select System and press OK. Select your country or part of the world where you are now. 2 Find channel To find a channel, select Find channel and press OK. Select Search and press OK. You can also enter a frequency yourself. If the reception is poor, press Search again. If you want to store the channel, select Done and press OK. 3 Fine tune To fine tune a channel, select Fine tune and press OK. You can fine tune the channel with u or v. If you want to store the channel found, select Done and press OK. 4 Store You can store the channel on the current channel number or as a new channel number. Select Store current channel or Store as new channel . You can redo these steps until you found all available analogue TV channels. Clock settings In some countries, digital broadcasts do not send UTC - Coordinated Universal Time information. The daylight saving change might be ignored and the TV might show an incorrect time. To correct the TV clock, press h > Setup > TV settings > Preferences > Clock and select Country dependent . Select Daylight saving and select the appropriate setting. To set the time and date manually, select Manual. Then select Time or Date . Setup / Channels45
4.4Satellite channels Introduction As well as the DVB-T and DVB-C reception, this TV has a built - in satellite DVB -S receiver . With a satellite dish antenna connected, you can receive digital satellite channels. You do not need an external satellite receiver. LNB An LNB (Low Noise Block-downconverter) captures the signals from a satellite and is mounted at the end of the pole on the dish antenna. The TV can receive signals from 4 different LNBs. Installation With a properly set -up and connected satellite dish antenna, you can install satellite channels on the TV. You can install channels from 4 different satellites (4 LNBs). 1 Install To search for satellites and install satellite channels, press h > Setup > Search for satellite and press OK. If you have already installed satellites, select Reinstall channels and press OK. 2 Connection type Before you start searching for satellites, you must set the connection type. The connection type will determine the number of LNBs you can install (the number of different satellites). For ease of installation, select the correct type for the number of satellites you want to install. To set up the connection type, select Settings and press OK. Select Connection type and select One LNB if you have only one LNB, select DiSEqC Mini for 2 LNBs or select DiSEqC 1.0 to install 3 or 4 LNBs. Select Done to close the settings. 3 Search for satellites To start the search, select Start and press OK. The TV searches for all available satellites. This can take several minutes. If no satellites are found, check the antenna connections and the position of the dish antenna. The signal quality shown is not always representative of the signal quality of all channels on that satellite. To repeat the search for satellites , select Restart and press OK. If you are satisfied with the satellites found, you can install all their channels. 4 Install channels To install all channels for the satellites you found, press Install. The installation can take several minutes per satellite. When the installation is finished, you can find all channels in the satellite Channel list. More settings For most satellites, you do not need to change the LNB settings but, if you are searching for a specific satellite on C -band for instance, you need to set the LNB you use for this satellite to Single . Or, if you are an expert user, you might need a Custom setting for the LNBs you use. Reset You might have lost track of the settings you set up. To reset the satellite installation settings to factory settings, select Reset in Settings and press OK. Signal reception test The automatic channel install might have missed a specific channel or channels from a transponder. You can add a transponder with Signal reception test. Read Help > Setup > Satellite channels > Signal reception test . Dish antenna connection Read more about the antenna connection for satellite in Help > Connections > First connections > Satellite antenna. Find the list of preset satellites on this TV in Help > Specifications > Power and reception . Add or remove If satellite channels are already installed, you can add an extra satellite to the installation. You can install channels from 4 different satellites - 4 LNBs. 1 Connection type Check the Connection type setting before you add a satellite. The setting One LNB receives only one LNB, the setting DiSEqC Mini receives only 2 LNBs and the setting DiSEqC 1.0 can receive 3 or 4 LNBs. To check the Connection type first, press h > Setup > Search for satellite and press OK. Select Reinstall channels and select Settings and press OK. Select Connection type and select the setting you need for the number of satellites you want to install. Select Done to close the settings. Press È to close Reinstall channels. 2 Add a satellite To add a satellite, press h > Setup > Search for satellite and press OK. Select Add satellite and press OK. The TV searches for a satellite on the first free LNB. This can take several minutes. If no satellites are found, check the antenna connections and the position of the dish antenna. Select Restart or Next LNB . If there are no free LNBs, you can remove a satellite first. Read Remove satellites on the following page. 3 Install channels If you are satisfied with the added satellite, you can install the channels. To install all channels, press Install. The installation can take several minutes. When installation is complete, you can find the added channels in the satellite Channel list. You can remove a satellite from your satellite installation. To remove a satellite, press h > Setup > Search for satellite . Select Remove satellite and press OK. Select the satellite you want to remove and press OK. To confirm, select Yes and press OK . The satellite and its channels are removed from the installation. 46Setup / Satellite channels
Update channels If satellite channels are already installed, you can update the channel list with possible new channels from all installed satellites. To update the satellite channels, press h > Setup > Search for satellite . Select Update channels and press OK. The TV scans the satellites for new channels and adds them to the list. Empty channels are removed from the list. The update can take several minutes per satellite. When the update has finished, the Channel list for satellites is updated. Signal reception test With Signal reception test for satellites, you can check the signal strength of a satellite or you can add a new satellite channel. To start Signal reception test, press h > Setup > Search for satellite . Select Signal reception test and press OK. 1 Select the LNB. 2 If you know the frequency of the transponder (which can hold several channels), select Frequency and enter it. 3 Select Search and press OK. 4 If the TV finds a frequency and there is a store button shown, a new transponder has been found. 5 Press Store to add the new transponder with its channel or channels to the Channel list. To add another transponder, select Exit and repeat the steps. Troubleshooting The TV cannot install the satellite I want • Check the orientation of the dish antenna. • Check the setting for the LNB that you use for this satellite. • Check the connection type in the satellite installation settings. • Reset all satellite settings if you lost track of the settings you changed. Read Help > Setup > Satellite channels > Installation. The reception of a satellite channel is poor • Check the orientation of the dish antenna. Sometimes the reception is poor • Check if the dish antenna is solidly mounted. Strong winds can move the dish. • Snow and rain can degrade reception. Read more about troubleshooting in Help > Troubleshooting . Setup / Satellite channels47
4.5Network Benefits Browse PC If you connect the TV to a home network, you can play photos, music and videos from your computer or storage device. Once the network is installed on the TV, you can find and play the files from your PC on the TV screen. Net TV If you connect the TV to a home network, you can link up the TV to Net TV. Net TV offers Internet services and websites tailored to your TV. Play music and videos, consult infotainment, rent movies and much more. Once the network is installed, you can enjoy the best of the Internet for your TV. Wi -Fi MediaConnect With Wi-Fi MediaConnect you can bring up (project) your PC screen on the TV screen wirelessly. You start Wi-Fi MediaConnect from your PC. What you need To connect the TV to a home network and the Internet, you need a router in your home network. The router must be set to DHCP server on. Use a router with a high -speed (broadband) connection to the Internet. You can connect the TV wirelessly or wired. If you use a wired connection to the router you need a network (Ethernet) cable. The TV uses a DLNA-certified protocol. You can use a computer with Microsoft Windows XP, Vista or Windows 7, Intel Mac OSX or Linux as the operating system. Find your PC files To select your PC files on screen, you need recent media server software on your computer, like Windows Media Player 11 or similar. To find your files on the TV, some media server software must be set up to share the PC files with the TV. Find the list of supported media server software in Help > Specifications > Multimedia . Wireless installation Switch on your router before you start the network installation. To start the wireless network installation , press h, select Setup > Connect to network and press OK. Follow the instructions on screen. WPS - Wi -Fi Protected Setup If your router has WPS (Wi-Fi Protected Setup) , go to the router and press the WPS button. Return to the TV within 2 minutes, select WPS and press OK. The TV connects to your network. This takes about 2 minutes. Finish the installation. Most new wireless routers have the WPS system and carry the WPS logo. The WPS system uses WPA security encryption and cannot be combined with devices on your network that use the WEP security encryption. If you still need this WEP device in your network, install with Scan > Standard . Scan for routers If you have several routers in your network, you can select the network you need. To select a specific network router, press Scan on the first page of the installation. The routers with WPS and with the strongest signal are shown first in the list. Select the router you need and press WPS if the router has WPS. Or press Pin code if you can enter the PIN code in your router software to connect. Or press Standard to enter the encryption key manually. PIN code To make the secured connection with a PIN code, select PIN code and press OK. Write down the 8 -digit PIN code shown and enter it in the router software on your PC. See the router manual where to enter the PIN code. Standard To enter the encryption key (the security key) manually, select Standard and press OK. If you have WPA security on your router, enter the passphrase with the remote control. To open the on -screen keyboard, select the text entry field and press OK. If you have WEP security encryption , the TV asks for the WEP encryption key in hexadecimal numbers. Find this hexadecimal key in the router software on your PC. Write down the first key of the WEP keys list and enter it on TV with the remote control. If the security key is accepted, the TV is connected with the wireless router. If asked, agree to the End User License Agreement. Wi- Fi Media Connect With Wi-Fi MediaConnect you can bring up (project) your PC screen on the TV screen wirelessly. With the supplied Wi-Fi MediaConnect CD-ROM you can download the software for free. Wi-Fi MediaConnect is only available for PC. What you need To use Wi-Fi MediaConnect, you need to connect the TV to your home network. You need a wireless router. Read more about connecting to a network in Help > Setup > Network . Install Wi -Fi MediaConnect 1 Insert the Wi-Fi MediaConnect CD-ROM into your PC. 2 Your PC starts your Internet browser and opens the Wi-Fi MediaConnect download page - www.philips.com/wifimediaconnect. On the website, you can check the necessary PC system requirements. 48Setup / Network
3 Enter the code printed on the CD-ROM envelope. 4 Click the Download now button to download the free Wi-Fi MediaConnect software. 5 Once downloaded, start the file Wi-Fi MediaConnect_setup.exe. Follow the instructions on screen. TV network name If you have more then one TV in your home network, you can rename this TV. To rename this TV in the network, press h > Setup > Network settings and select TV network name . To enter the name, press OK to open the on -screen keyboard or use the remote control keypad. To use Wi-Fi MediaConnect on your PC read Help > More TV > Videos, photos and music > Wi -Fi MediaConnect. PC requirements Windows XP, Vista, Windows 7 (PC only) Minimum PC requirements • Intel® Pentium Core™ 2 Duo 1.8GHz • 512MB RAM • 200MB free hard disk space • Wi-Fi 802.11g • Broadband Internet connection Recommended PC requirements • Intel® Pentium Core™ 2 Duo 2.1GHz • 1GB RAM • 200MB free hard disk space • Wi-Fi 802.11n for router and PC • Broadband Internet connection Wired installation Connect the router to the TV and switch on your router before you start the network installation. To start the network installation, press h, select Setup > Connect to network and press OK. Follow the instructions on screen. The TV constantly searches for a network connection. The router must be set to DHCP server on. If asked for, agree to the End User License Agreement. Read more about how to connect in Help > Connections > Network > Wired . Network settings To open the Network settings, press h > Setup > Network settings and press OK. You can view the network type, IP and MAC address, the signal strength, speed and encryption method etc. You can set DHCP and Auto IP, the IP configuration settings, DMR and the TV network name. Setup / Network49
4.6Devices EasyLink HDMI- CEC With EasyLink HDMI -CEC your TV and the connected devices can work together. You can use the TV remote control to operate EasyLink devices. The device needs to be connected with an HDMI cable. Devices with EasyLink appear automatically in the Home menu. Setup The TV comes with EasyLink switched on. Make sure that all HDMI -CEC settings are properly set up on the connected EasyLink devices. EasyLink might not work with devices from other brands. Switch off EasyLink RC If you dont want to operate devices with the TV remote control, you can switch off EasyLink remote control separately. Press Home h > Setup > TV settings and select EasyLink > EasyLink Remote Control and select Off. Switch off EasyLink To switch off EasyLink completely, press Home h > Setup > TV settings and select EasyLink > EasyLink On/Off and select Off . HDMI-CEC on other brands The HDMI -CEC functionality has different names on different brands. Some examples are: Anynet, Aquos Link, Bravia Theatre Sync, Kuro Link, Simplink and Viera Link. Not all brands are fully compatible with EasyLink. Read more about using EasyLink in Help > Use your TV > Remote control > Operate devices . Add a new device Devices connected with EasyLink HDMI -CEC automatically show their activity in the Home menu. A single device can add several activities. The device must be connected with an HDMI cable. If your connected device does not appear in the Home menu, on the device EasyLink may be switched off. If your connected device does not have EasyLink or is not connected with an HDMI cable, you need to manually add your device with Add your devices in the Home menu. Add your devices In the Home menu, select Add your devices and press OK. Follow the instructions on screen. The TV asks you to select the device and the connection to which the device is connected. The device or its activities are now added to the Home menu. Rename a device To rename a device in the Home menu, select the device and press rOPTIONS and select Rename. Use the keypad on the remote control as you do for SMS/text messaging to enter the new name or press OK to open the on -screen keyboard. Delete a device To delete a device or activity from the Home menu, select the item and press rOPTIONS and then select Remove this device . If the device or activity, keeps appearing in the Home menu after you deleted it, switch off the EasyLink setting on the device to prevent the icon from being automatically added again. Audio to Video sync With a Home Theatre System (HTS) connected to the TV, the picture on TV and the sound from the HTS should be synchronised. A mismatch can be visible in scenes with people talking. When they finish sentences before their lips stop moving. Automatic audio to video sync With recent Philips Home Theatre Systems, the audio to video sync is automatically synchronised and always correct. Audio sync delay Other Home Theatre Systems might need to adjust the audio sync delay to synchronise the audio to video. On the HTS, increase the delay value until there is a match between picture and sound. A delay value of 180ms may be required. Read the user manual of the HTS. With a delay value set up on the HTS, you need to switch off Audio Out delay on the TV if the HTS sets an identical delay for all its incoming audio. To switch off Audio Out delay, press h and select Setup > TV settings > Preferences > Audio Out delay . Select Off and press OK. If you cannot set up a delay on the HTS or its maximum setting is insufficient, you can switch off the Perfect Natural Motion picture processing of the TV. To switch off Perfect Natural Motion, press h and select TV settings > Picture > Perfect Natural Motion . Select Off and press OK. Auto subtitle shift If you play a DVD or Blu-ray Disc on a recent Philips player, the TV can move the subtitles upwards. Subtitles will then be visible whatever Picture format you select. The TV comes with Auto subtitle shift switched on. To switch off Auto subtitle shift, press h > Setup > TV settings > EasyLink > Auto subtitle shift . Select Off. Pixel Plus link Some other devices, DVD or Blu-ray Disc players, might have their own picture quality processing. To avoid bad picture quality caused by interference with the TV processing, the picture processing of these devices should be disabled. The TV comes with Pixel Plus link switched on and disables the picture quality processing of recent Philips devices connected to the TV. To switch off Pixel Plus link, press h > Setup > TV settings > EasyLink > Pixel Plus link . Select Off. 50Setup / Devices