Philips 32pfl3205 User Manual

							9
Switch channels
Press  • P +/- on the remote control or 
P/CH +/- on the side of the T V.
Enter a channel number using the  • 
Numeric buttons.
Press  • OK to use the channel grid.
Press  • 
 BACK P/P on the remote 
control to return to the previous channel. 
Note
When you use a favourite list, you can only   •select those channels in the list (see ‘Select a 
favourite list’ on page 15).
Switch channels with the channel grid
The channel grid allows you to view all 
available channels in a grid format.
 
1 Press OK.
The channel grid appears.   »
2 Press  to select and preview a 
channel.
3 Press OK to watch the selected channel.
4 Use your TV
This section helps you perform basic TV 
operations.
Switch your TV on / off or to 
standby
 
 
To switch on
If the standby indicator is off, press   • 
 (Power) at the side of the T V.
If the standby indicator is red, press   • 
 (Standby-On) on the remote control.
To switch to standby
Press  • 
 (Standby-On) on the remote 
control.
The standby indicator switches to red.   »
To switch off
Press  • 
 (Power) at the side of the T V.
The standby indicator switches off.   »
Tip
Though your T V consumes ver y lit tle power   •when in standby, energy continues to be 
consumed. When not in use for an ex tended 
period of time, disconnect the TV power cable 
from the power outlet.
Note
If you cannot locate your remote control and   •want to switch on the T V from standby, press 
P/CH +/- on the side of the T V.
English
EN
 
						

							10
Use teletext
 
1 Press MHEG/TELETEXT.
The main index page appears.   »
2  Select a page as follows:
Press the  • Numeric buttons to enter 
a page number
Press  • P +/- to view the nex t or 
previous page
Press the  • Colour buttons to select a 
colour coded item
Press  • 
 BACK to return to a 
previously viewed page
3 Press MHEG/TELETEXT to exit teletext.
Watch connected devices
Note
Switch on the device before selecting it as a   •source on the T V.
Use the source button
  
1 Press  SOURCE.
The source list appears.   »
2 Press  to select a device.
3 Press OK to confirm your choice.
The TV switches to the selected    »
device.
Adjust TV  volume
 
 
To increase or decrease volume
Press  • 
 +/-.
To mute or unmute sound
Press  • 
 to mute the sound.
Press  • 
 again to restore the sound.
EN
 
						

							11
Rename devices from the 
home menu
After adding a new device to the home menu, 
you can rename it to your preference.
1 Press  MENU.
2 Press  to select a device to rename.
3 Press  OPTIONS.
The options menu appears.   »
4 Press  to select [Rename device], then 
press OK.
A text input box appears.   »
5 Press  to select characters.
6 Press OK to confirm each character.
7 Select [Done], then press OK to finish 
renaming devices.
Note
The device name can be up to six characters   •long.
Press   •[Aa] to change an uppercase let ter to a 
lowercase let ter and vice versa.
Remove devices from the 
home menu
If a device is no longer connected to the TV, 
remove it from the home menu.
1 Press  MENU.
2 Press  to select a device to remove.
3 Press  OPTIONS.
4 Press  to select [Remove device], then 
press OK.
5 Select [Remove], then press OK.
The selected device is removed from    »
the home menu.
5  Use more of 
your TV
Access TV  menus
Menus help you to install channels, change 
picture and sound settings and access other 
features.
1 Press  MENU.
The menu screen appears.   »
  
2 Press  to select and navigate 
through one of the following menus.
• [Watch TV]: Switches back to the 
aerial source if another source is 
selected.
• [Add new device]: Adds new devices 
to the home menu.
• [Setup]: Accesses menus to change 
picture, sound and other settings.
3 Press OK to confirm your choice.
4 Press  MENU to exit.
Tip
After selecting   •[Add new device], follow the 
on-screen instructions to select the correct 
device and connector.
Add new deviceWatch TVSetup
English
EN
 
						

							12
Manually adjust picture settings
1 Press  MENU.
2 Press  to select [Setup]  > 
[Picture] .
3 Press  to select the following 
settings.
•	 [Smart picture]
:	Accesses	pre-defined	
smar t picture settings.
•	 [Video contrast] : Adjusts the intensity 
of video contents, keeping backlight 
unchanged.
•	 [Contrast] : Adjusts the intensity of 
backlight areas, keeping video contents 
unchanged.
•	 [Brightness]: Adjusts the intensity and 
details of dark areas.
•	 [Colour] : Adjusts colour saturation.
•	 [Hue] : Compensates for colour variations.
•	 [Sharpness] : Adjusts sharpness in the 
image.
•	 [Noise reduction] : Filters and reduces 
noise in an image.
•	 [ Tint] : Adjusts the colour balance in an 
image. 
•	 [Custom tint] : Customises tint setting. 
(Only available if  [ Tint] > [Custom]  is 
selected)
•	 [Crystal Clear] : Fine-tunes each pixel to 
match surrounding pixels. This produces a 
brilliant,	high-definition	image.
•	 [Dynamic contrast] : Enhances 
contrast. You can switch this feature 
on or off.
•	 [Dynamic backlight] : Adjusts 
brightness of the T V backlight to 
match lighting conditions.
•	 [Colour enhancement] : Makes 
colours more vivid and improves 
the details in bright colours. You can 
switch this feature on or off.
•	 [PC mode] : Adjusts the picture when a 
PC is connected to the T V via HDMI or 
DVI.
•	 [Picture format] : Changes the picture 
format.
Change picture and sound 
settings
Change picture and sound settings to suit your 
preferences. 	You	can	apply	pre-defined	settings	
or change settings manually.
Note
When watching T V or using ex ternal devices,  •press  OPTIONS then select  [Picture and 
sound]  for quick access to picture and sound 
settings.
Use smart picture
Use	smar t	picture	to	apply	pre-defined	
picture settings.
1  Press  PICTURE.
The 
 » [Smart picture] menu appears.
2 Press  to select one of the following 
settings.
•	 [Vivid] : Applies rich and dynamic 
settings.
•	 [Standard] : Adjusts picture settings 
to suit most environments and types 
of video.
•	 [Cinema] : Applies settings for movie 
viewing.
•	 [Game] : Applies settings for games.
•	 [Energy saving] : Applies low-energy 
settings.
•	 [Natural] : Applies the best picture 
quality.
•	 [Custom] : Lists customised picture 
settings.
3  Press OK	to	confirm	your	choice.
The selected smar t picture setting is  »
applied.
EN
 
						

							13
 
[Subtitle zoom]: Displays 
4:3 pictures over the full 
area of the screen, with 
sub-titles visible. Par t of 
the top of the picture is 
clipped off.
 
[Movie expand 14:9]: (Not 
for HD and PC mode.) 
Scales 4:3 format to 14:9.
 
[Movie expand 16:9]: 
(Not for HD and PC 
mode.) Scales 4:3 format 
to 16:9.
 
[Wide screen]: Scales 4:3 
format to 16:9.
 
[Unscaled]: Available in 
selected models with 
PC resolution under 
1024 x 768, only. Allows 
maximum sharpness. 
Some distor tion may 
be present due to the 
broadcaster’s systems. 
Set your PC resolution to 
wide screen mode for best 
results.
• [Picture size]: Adjusts the viewing area. 
(when set to maximum, you might see 
noise or a rough edge of an image.)
• [Horizontal shift]: Adjusts the picture 
horizontally for PC-VGA input.
• [Vertical shift]: Adjusts the picture 
ver tically for PC-VGA input.
Change picture format
1 Press  FORMAT.
A picture format bar appears.   »
2 Press  to select a picture format.
The selected picture format is    »
activated.
3 Press OK to confirm your choice.
Summary of picture formats
The following picture settings can be 
configured.
Note
Depending on the format of the picture   •source, some picture set tings are not available.
English
EN
 
[Auto format]: (Not for 
HDMI, YPbPr or PC mode.) 
Automatically displays the 
suitable picture format. If 
not, widescreen is applied.
 
[Super zoom]: (Not 
for HD and PC mode.) 
Removes the black bars on 
the side of 4:3 broadcasts. 
There is minimal 
distor tion.
 
[4:3]: Shows the classic 4:3 
format.
 
						

							14
• [Auto volume]: Automatically 
reduces sudden volume changes, for 
example, when switching channels. 
• [Delta volume]: Levels out volume 
differences between channels or 
connected devices. Switch to the 
connected device before you change 
the delta volume.
Use advanced teletext 
features
Access the teletext options menu
Access the teletex t features through the 
teletex t options menu.
1 Press MHEG/TELETEXT.
The teletext screen appears.   »
2 Press  OPTIONS.
The teletext options menu appears.   »
3 Press  to select one of the following 
options.
• [Freeze page]: Freezes the current 
page.
• [Dual/Full screen]: Enables and 
disables dual screen teletext.
• [Reveal]: Hides or reveals hidden 
information on a page, such as 
solutions to riddles or puzzles.
• [Cycle subpage]: Cycles through 
subpages automatically if subpages 
are available.
• [Language]: Switches to a different 
language group to display a language 
correctly when it uses a different 
character set.
4 Press  to make a selection, then 
press OK to confirm.
5 Press  BACK to exit the teletex t 
options menu.
Use smart sound
Use smar t sound to apply pre-defined sound 
settings.
1 Press  SOUND.
The    »[Smart sound] menu appears.
2 Press  to select the following settings.
• [Standard]: Adjusts sound settings 
to suit most environments and types 
of audio.
• [News]: Applies settings for spoken 
audio, such as news.
• [Movie]: Applies settings for movies.
• [Custom]: Applies the settings that 
were customised in the sound menu.
3 Press OK to confirm your choice.
The selected smar t sound setting is    »
applied.
Manually adjust sound settings
1 Press  MENU.
2 Press  to select [Setup] > [Sound].
The    »[Sound] menu appears.
3 Press  to select the following 
settings.
• [Smart sound]: Accesses pre-defined 
smar t sound settings.
• [Bass]: Adjusts the bass level.
• [Treble]: Adjusts the treble level.
• [Volume]: Adjusts the volume.
• [Balance]: Adjusts the balance of the 
right and lef t speakers.
• [Dual I-II]: Selects audio languages if 
dual sound broadcast is available.
• [Mono/Stereo]: Selects mono 
or stereo if stereo broadcast is 
available.
• [TV speakers]: Turns T V speakers 
on or off. Setting T V speakers 
to automatic mode turns off the 
speakers when content from an 
EasyLink-compliant home theatre 
system is detected.(Only available if 
EasyLink is switched on.)
• [Surround]: Enables spatial sound.
EN
 
						

							15
Create and use list of 
favourite channels
You can create a list of your preferred TV 
channels so that you can find those channels 
easily.
Select a favourite list
1  When watching T V, press OK to display 
the channel grid.
2 Press  OPTIONS.
The channel options menu appears.   »
3 Press  to select [Select list], then 
press OK to enter.
The channel list options appear.   »
4 Select [Favourite], then press OK.
Only channels in the favourite list    »
appear in the channel grid.
Note
The favourite channel grid is empty until you   •add channels into the favourite lists.
View all channels
You can exit a favourite list, and view all 
installed channels.
1  When watching T V, press OK.
The channel grid appears.   »
2 Press  OPTIONS.
The channel options menu appears.   »
3 Press  to select [Select list], then 
press OK or 
 to enter.
4 Select [All], then press OK. 
All channels are displayed in the    »
channel grid.
Note
All favourite channels are marked by an   •asterisk when you view the channel grid.
Select teletext subpages
A teletex t page can hold several subpages. 
Subpages are displayed on a bar nex t to the 
main page number.
1 Press MHEG/TELETEXT.
The teletext screen appears.   »
2 Press P +/- to select a teletex t page.
3 Press  to enter a subpage.
Select T.O.P. teletext broadcasts
Table Of Pages ( T.O.P.) teletex t broadcasts 
allow you to jump from one subject to 
another without using page numbers. T.O.P. 
teletex t is not broadcast on all T V channels.
1 Press MHEG/TELETEXT.
The teletext screen appears.   »
2 Press  INFO.
The T.O.P. over view appears.   »
3 Press  to select a subject.
4 Press OK to view the page.
English
EN
 
						

							16
Display the TV clock
1  When watching T V, press  OPTIONS.
The TV option menu appears.   »
2 Select [Clock].
3 Press OK.
Use timers
You can set timers to switch the TV to standby 
at a specified time.
Tip
Set the T V clock before you use timers.  •
Automatically switch the TV to 
standby (sleep timer)
Sleep timer switches the T V to standby af ter a 
pre-defined period of time.
Tip
You can switch off your T V earlier or reset the   •sleep timer during the countdown.
1 Press  MENU.
2 Press  to select [Setup] > 
[Features] > [Sleep timer].
The    »[Sleep timer] menu appears.
3 Press  to select a value between zero 
and 180 minutes. 
The sleep timer can be set in steps of    »
five minutes. If set to zero, the sleep 
timer is switched off.
4 Press OK to switch on the sleep timer.
The TV switches to standby after the      »
specified time.
Add a channel to a favourite list
1  When watching T V, press OK.
The channel grid appears.   »
2 Press  to select a channel to add to 
a favourite list.
3 Press  OPTIONS.
The channel options menu appears.   »
4 Select [Mark as favourite], then press 
OK.
The channel is added to the favourite    »
list.
Note
All favourite channels are marked by an   •asterisk in the channel grid.
Remove a channel from a favourite 
list
1  When watching T V, press OK.
The channel grid appears.   »
2 Press  to select a channel to 
remove.
3 Press  OPTIONS.
4 Select [Unmark as fav.], then press OK.
5 Select [Yes], then press OK.
The channel is removed.   »
Use the TV clock
You can display a clock on the TV screen. 
Set the TV clock
1 Press  MENU.
2 Select [Setup] > [Features] > [Clock]
The    »[Clock] menu appears.
3 Press  or Numeric buttons to 
enter time.
4 Select [Done] and press OK to confirm.
5 Press  MENU to exit.
EN
 
						

							17
Lock or unlock the TV
Lock the T V to prevent access to all channels 
and connected devices.
1 Press  MENU.
2 Press  to select [Setup] > 
[Features] > [TV lock].
You are prompted to enter your PIN    »
code.
3  Enter your code using Numeric buttons.
The    »[TV lock] menu appears.
4 Press  to select [Lock] or [Unlock].
5 Press OK to confirm.
All channels and connected devices are    »
locked or unlocked.
6 Press  MENU to exit.
Note
Switch the T V off and on again for the change   •to take effect.
If you select   •[Lock], you have to enter your 
code ever y time you turn on your T V.
Lock or unlock one or more channels
1  When watching T V, press OK to display 
the channel grid.
2 Press  to select a channel to lock or 
unlock.
3 Press  OPTIONS.
4 Press  to select [Lock channel] or 
[Unlock channel].
5  For each selection, press OK to lock or 
unlock the channel.
You are prompted to enter your PIN    »
code. 
6  Enter your code and press OK.
If the channel is locked, a lock icon is    »
displayed.
Automatically switch the TV on (on 
timer)
You can switch on the T V from standby to a 
specific channel at a specified time.
1 Press  MENU.
2 Press  to select [Setup] > 
[Features] > [On timer].
3 Press  to enter the [On timer] menu.
• [Activate]: Selects how of ten the T V 
is switched on.
• [Time]: Sets the time to switch on 
the T V.
• [Programme no.]: Selects the 
channel or the connected device.
4 Press  MENU to exit.
Tip
Select   •[On timer] > [Activate] > [Of f ] to 
disable this feature. 
Use TV  locks
You can prevent your children from watching 
cer tain programmes or channels by locking the 
TV controls. 
Set or change your PIN code
1 Press  MENU.
2 Press  to select [Setup] > 
[Features] > [Set code] / [Change code].
The    »[Set code] / [Change code] menu 
appears.
3  Enter your code using the Numeric 
buttons.
Follow the on-screen instructions to    »
create or change your PIN code.
Tip
If you forget your code, enter ‘8888’ to   •override any existing codes.
English
EN
 
						

							18
View photos
1  In the USB browser, press  to enter the 
[Picture] folder.
2 Press  to select a photo or a photo 
album.
3 Press OK to view a full screen image of 
the photo.
Tip
When in full screen mode, press   • to move 
between photos. 
View a slide show of your photos
1  When a full screen image of a photo is 
displayed, press OK.
A slide show begins from the selected    »
photo.
2  Press the following buttons to control the 
slide show:
• OK to pause the slide show.
• 
 to go back or move for ward to 
the next image.
• 
 BACK to stop the slide show. 
7  Repeat the process to lock or unlock 
more channels.
Note
Switch the T V off and on again for the change   •to take effect.
If you access the locked channels by pressing    •P +/- on the remote control or from the 
channel grid, you are prompted to enter your 
PIN code. 
View photos and play music 
from a USB storage device
Caution
Philips is not responsible if the USB storage   •device is not suppor ted, nor is it responsible 
for damage or loss of data from the device.
Use the USB connector to view photos or 
listen to music stored on a USB storage device.
1  Turn on the T V.
2  Connect the USB storage device to the 
TV.
The home menu appears.   »
3 Press  to select [Browse USB].
4 Press OK to confirm.
The USB thumbnail browser appears.   »
Tip
Press   • GUIDE to switch between thumbnail 
and file browsing views.
EN