Philips 200aw8f User Manual

							
   
       
 
 
• 
Front View 
Produt 
Description
 • 
Connecting 
to Your PC
 • Getting 
Started 
 • Optimizing 
Performance
Installing Your LCD Monitor
Front View Product Description
 
 
 
 
1To switch monitor’s power on and off
2
MENUTo access OSD menu
3
Hot key of Contrast adjustment and To adjust OSD value up 
when OSD menu is active
4
Hot key of Brightness adjustment and To adjust OSD value 
down when OSD menu is active 
5
  Automatically adjust the horizontal position, vertical position, 
phase and clock settings
 
RETURN TO TOP OF THE PAGE
Rear View
 
						

							
RETURN TO TOP OF THE PAGE
Optimizing Performance
For best performance, ensure that your display settings are set at 1680x\
1050, 60Hz.
Note: To check the current display resolution, press the OK button once. 
The current display mode is shown on the OSD. If the display setting is \
not 
optimized, a warning string USE 1680x1050 FOR BEST RESULT appears in 
the OSD menu.
You can also install the Flat Panel Adjust (FP Adjustment) program, a program for getting the best 
performance out of your monitor. This is included on this CD. Step-by-st\
ep instructions are 
provided to guide you through the installtion process. Click on the link\
 to know more about this 
program.
More about FP_setup4.3.exe
RETURN TO TOP OF THE PAGE
1AC power input
2DVI-D input
3VGA input
4Kensington anti-thief lock
5PC Audio input
1234
AC INVGADVILINE IN
56
6Speaker
 
						

							
   
        
  1.Put base on the desk and 
insert whole unit into base 
vertically  
 2.Check if insertion ok
 
   
   
 
 
     3.Put whole unit horizontally 
 
      
   
 
 
 
						

							
  RETURN TO TOP OF THE PAGE 
 
 
   
       
 
						

							
•Front View 
Product
Description
• Accessory 
Pack
• Connecting 
to Your PC
• Getting 
Started
• Optimizing 
Performance
Connecting to Your PC
Accessory Pack
Unpack all the parts.
Power cordVGA cableEDFU CD
DVI cable (Optional)
RETURN TO TOP OF THE PAGE
Connecting to Your PC
1)
Audio cable
 
						

							
2)
3) Cable management
4)Connect to PC
1123
4
2
3
5
200AW8
 
						

							
(1)AC power input
(2)DVI-D input
(3)VGA input
(4)Kensington anti-thief lock
(6)Set your Monitor at 1680x1050@60Hz for best performance. It is also 
strongly recommended to use DVI input (may require the optional DVI cab\
le) 
for the true digital enjoyment.
RETURN TO TOP OF THE PAGE
(5)PC Audio input
 
						

							
   
       
 
 
Your LCD 
Monitor :
 
• Front View 
Product 
Description
 
• Setting Up 
and 
Connecting 
Your 
Monitor
 • Getting Started 
 • Optimizing Performance
  
 
   
   
   
   
   
   
Getting Started 
Getting Started 
Use the information file ( .inf) for Windows® 95/98/2000/Me/XP
/Vista or later 
The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play\
 requirements 
for Windows® 95/98/2000/Me/XP
/Vista. This information file ( .inf) should be installed in 
order that your Philips monitor can be enabled from the Monitor dialog box i\
n Windows® 

95/98/2000/Me/XP
/Vista and the Plug & Play application can be activated. The installation 

procedure based on Windows® 95 OEM Release 2 , 98 , 
2000,Me, XP and Vista is specified 
as follows.

For Windows® 95 
1.  Start Windows® 95 
2.  Click on the Start button, point to Settings, and then click on Con\
trol Panel. 
3.  Double click on the Display Icon. 
4.  Select the Settings tab then click on Advanced.... 
5.  Select the Monitor button, point to Change... then click on Have Di\
sk.... 
6.  Click on the Browse... button, select the appropriate drive F: ( CD-R\
OM Drive) 
then click on the OK button. 
7.  Click on the OK button then select your monitor model and click on OK\
. 
8.  Click on the Close button. 
For Windows® 98 
1.  Start Windows® 98 
2.  Click on the Start button, point to Settings, and then click on Con\
trol Panel. 
3.  Double click on the Display Icon. 
4.  Select the Settings tab then click on Advanced.... 
5.  Select the Monitor button, point to Change... then click on Next 
6.  Select Display a list of all the drivers in a specific location, so you\
 can choose the 
driver you want. then click on Next and then click on Have Disk....\
 
7.  Click on the Browse... button, select the appropriate drive F: ( CD-R\
OM Drive) 
then click on the OK button. 
8.  Click on the OK button then select your monitor model and click on the\
 Next 
button. 
9.  Click on the Finish button then the Close button. 
For Windows® 2000 
1.  Start Windows® 2000 
2.  Click on the Start button, point to Settings, and then click on Con\
trol Panel. 
3.  Double click on the Display Icon. 
4.  Select the Settings tab then click on Advanced.... 
5.  Select Monitor 
- If the Properties button is inactive, it means your monitor is prope\
rly configured. 
Please stop installation. 
- If the Properties button is active. Click on Properties button. Pl\
ease follow the 
steps given below. 
6.  Click on Driver and then click on Update Driver... then click on the\
 Next button. 
 
						

							
7.Select Display a list of the known drivers for this device so that I ca\
n choose a 
specific driver, then click on Next and then click on Have disk....\
 
8.Click on the Browse... button then select the appropriate drive F: ( \
CD-ROM 
Drive).
9.Click on the Open button, then click on the OK button. 
10.Select your monitor model and click on the Next button. 
11.Click on the Finish button then the Close button. 
If you can see the Digital Signature Not Found window, click on the Y\
es button. 
For Windows® Me
1.Start Windows® Me 
2.Click on the Start button, point to Settings, and then click on Con\
trol Panel. 
3.Double click on the Display Icon. 
4.Select the Settings tab then click on Advanced.... 
5.Select the Monitor button, then click on Change... button. 
6.Select Specify the location of the driver(Advanced) and click on the\
 Next button. 
7.Select Display a list of all the drivers in a specific location, so you\
 can choose the 
driver you want, then click on Next and then click on Have Disk....\
 
8.Click on the Browse... button, select the appropriate drive F: ( CD-R\
OM Drive) 
then click on the OK button. 
9.Click on the OK button, select your monitor model and click on the Ne\
xt button. 
10.Click on Finish button then the Close button. 
For Windows® XP
1.Start Windows® XP
2.Click on the Start button and then click on Control Panel.
3.Select and click on the category Printers and Other Hardware
4.Click on the Display Item.
5.Select the Settings tab then click on the Advanced button.
6.Select Monitor tab
- If the Properties button is inactive, it means your monitor is prope\
rly configured. 
Please stop installation.
- If the Properties button is active, click on Properties button.
Please follow the steps below.
7.Click on the Driver tab and then click on Update Driver... button.
8.Select the Install from a list or specific location [advanced] radio b\
utton and then 
click on the Next button.
9.Select the Dont Search. I will choose the driver to install radio but\
ton. Then click 
on the Next button.
10.Click on the Have disk... button, then click on the Browse... button\
 and then 
select the appropriate drive F: (CD-ROM Drive).
11.Click on the Open button, then click the OK button.
12.Select your monitor model and click on the Next button.
- If you can see the has not passed Windows® Logo testing to verify \
its 
compatibility with Windows® XP message, please click on the Continu\
e Anyway 
button.
13.Click on the Finish button then the Close button.
14.Click on the OK button and then the OK button again to close the 
Display_Properties dialog box.