Panasonic Wv Nw474s Operating Instructions Manual

-21- 4. Click the Menu ON button to overlay the ** SET
UP ** menu on the camera image. The cursor is
highlighted on the window.
5. Move the cursor to SETUP DISABLE if it is dis-
played, or skip to step 7 if ENABLE is displayed.
6. Click the SET button. 
DISABLE will change to ENABLE, and the camera is
now ready to be set up.
Note:While DISABLE is displayed, setup operations
are disabled.
7. Move the cursor to CAMERA 
O, and click the SET
button. CAM SETUP opens. 
Notes: 
•Refer to the next page for setup...

-22-
■Setup Menu Tree
** SET UP **** CAM  SET UP **
ALC 
CAMERA ID
AGC 
SHUTTER 
SYNC 
SENS UP 
MOTION DET 
WHITE BAL 
CAMERA ID
** ALC CONT ** MASK SET
** AWC  ** 
** MOTION DETECT ** 
CHROMA GAIN 
UPSIDE DOWN ** SPECIAL ** 
PEDESTAL 
AP SHARP 
EL-ZOOM 
HUE 
BURST(B/W) 
BW 
CAMERA RESET
MENU/DIP SW
NET MASK 
IP ADDRESS** NETWORK SETUP ** 
HTTP PORT NO. 
DHCP
GATEWAY 
↵
↵
ATW1
ATW2 

Opening the camera setup menu
■Camera Setup Menu (CAM
SETUP)
1. Camera Identification (CAMERA ID) Setting
You can assign a name to the camera.  The camera ID
consists of up to 16 alphanumeric characters.  The
camera ID display can be switched on and off on the
monitor screen.
-23-
SETTING PROCEDURES
The following pages describe setting operations from the camera. 
For accessing from the PC, interpret these instructions as follows.
Escaping from the VMD mask setup
etc.Function
Closing the camera setup...

-24-
To edit the CAMERA ID
1. Move the cursor to CAMERA ID.
The factory default setting is OFF.
2. Press [SET]. The CAMERA ID menu appears.  The
cursor on the letter 0 is highlighted.
3. Move the cursor to the character you want to edit by
pressing [Left]/[Right]/[Up]/[Down].
4. After selecting the character, press [SET]. The
selected character appears in the editing area. (The
cursor in the editing area moves to the right auto-
matically at this moment.)
5. Repeat the steps above until all characters...

-25- 3. Move the cursor to the area where backlight is
bright and press [SET] to mask that area. The mask
turns to white.(When the cursor is moved on an
area that has already been masked, the mask and
cursor start blinking.)
4. Repeat step 3 to mask the desired areas. To cancel
masking, move the cursor to that area and press
[SET].
5. After masking is completed, press [SET] for 2 sec-
onds or more. The ALC CONT menu appears.
6. If you want to change the video output level (picture
contrast), move the I...

-26-
6. Synchronization Setting (SYNC)
There are three synchronization modes: INT (internal),
LL (line-lock), and VD2 (vertical drive). You can select
the internal or line lock mode in the menu setup, but
you cannot select VD2. The VD2 signal is supplied from
an external device e.g., a Video Multiplexer, by being
multiplexed on a coaxial cable, and it overrides the
internal and line-lock mode even when these modes are
selected in the menu.
Note:The priority for sync sources is: VD2 (highest) –
LL – INT...

-27-
•Automatic White Balance Control Mode (AWC)
In this mode, accurate white balance is obtained
within a color temperature range of approximately
2300-10 000 K.
1. Move the cursor to WHITE BAL and select AWC 
→
PUSH SW.
2. Press [SET] to start white balance setup. PUSH SW
is highlighted to indicate that white balance is being
set.
3. When the white balance setting is completed, PUSH
SW returns to normal display.
Note:If white balance is not set, PUSH SW is being
highlighted.
4. When you want to adjust...

-28- •The camera will deactivate the detector for a few
minutes after the power of the camera is turned on
or the BW setting in the Special Menu is set to
something other than OFF.
•The motion detection function is not designed
specifically for prevention of theft, fire, etc.
9. Menu/DIP SW Selection
Some of the settings: picture upside down, aperture
level, BW, and synchronization: are operable in the
menu setup or from the DIP switch on the camera. You
can select MENU or DIP SW in the second from the...

-29- 5. Press [Up] or [Down] to zoom in or out the image.
6. Move the cursor to PUSH SET for PAN/TILT and
press [SET]. The PAN/TILT setting menu appears.
7. Press [Up] or [Down] [Left] or [Right] to change the
angular field of view.
8. To return to the EL-ZOOM setting menu, press
[SET].
10-7. BW
This function lets you switch from color to black-and-
white picture automatically in low light conditions such
as at night.
1. Move the cursor to BW.
2. Select AUTO1, AUTO2, EXT, ON or OFF using [Left]
or...

-30-
■Network Setup (NETWORK
SETUP)
Set up network parameters when connecting the
10/100BASE jack with a network.
Notes:
•Access the setup menu from the PC to use the
DHCP or DNS server, because these settings are
not included in this window.
•Ask your system administrator or ISP (Internet
Service Provider) about available IP address, subnet
mask, and gateway, prior to setup.
•The assigned address should be a global type when
connecting via the Internet. Ask your ISP whether it
is.
1. Move the cursor to...