Panasonic Wv Nw474s Operating Instructions Manual

-11-
■Mounting the Camera
Disassembling the Camera
1. Remove the dome cover by loosening the three
tamper-proof screws with the supplied bit.
2. Remove the two red-colored screws provided for
transport protection with a Philips screwdriver.
Note:Prior to installation, discharge static electricity by
placing your hands on a metallic surface. Failure to
do so may damage the components inside the cam-
era.
Optional Heater Unit
Assemble the optional heater unit into the camera if
necessary. Refer to APPENDIX...

•Cable length and wire gauge
The recommended cable length and thickness are
shown in the table for reference. The voltage sup-
plied to the power terminals of the camera should
be between 
19.5 V ACand 28 V AC.
●Power Connection
Use individual power sources for the camera and
optional heater unit.
•Wire colors & functions
-12-
■Connections
Cautions:
•This product should be installed and connected in conformity with NEC by qualified service personnel or system
installers.
•Do not use a transformer with a...

-13-
●Video Output Connection
Connect the video output cable to the monitor or other
system device with the procured coaxial cable. The
maximum extensible length is shown in the table.
●Control Connector
Connect the respective peripherals to supply and
receive control signals. Use the supplied 5-pin cable
adapter. For electrical ratings, refer to SPECIFICA-
TIONS.
●Network Port Connection
Connect the network port to a PC or a network via a
hub with a 10BASE-T/100BASETX cable. Use the sup-
plied adapter...

-14- 3. Zoom
•Unlock the zoom lever.
•Move the lever to adjust the zoom.
•Lock the lever.
4. Focus
•Unlock the focus lever.
•Move the lever to adjust the focus.
•Lock the lever.
5. Reinstalling the dome cover
•Attach the dome cover to the camera so that the two
position marks match.
•Tighten the three tamper-proof screws.
●Waterproof Process
If necessary, apply waterproof process to protect the
camera from water soak.
•Power cord
Tape individual wires first, and finally all of them as a
whole.
•Connector...

●Connection to Internet (Type 3)
The PC accesses the camera through the Internet and
the DSL/CATV modem.
Necessaries: 
•Straight-type network cable (Category 5)
•CATV modem (cable modem) or DSL modem 
●Connection to Internet (Type 4)
A switching hub or a router may be added to type 3
connection.
Necessaries: 
•Straight-type network cable (Category 5)
•CATV modem (cable modem) or DSL modem 
•Switching hub or router (10BASE-T/100BASE-TX
applicable)
Notes:
•Setting the router is required when connecting...

-16-
■Network Setup of Your PC
To set up the network of the PC, first change the TCP/IP
settings of the PC to match them to the default settings
of the camera. 
The following are the default network settings of the
camera.
IP address : 192.168.0.10
Subnet mask : 255.255.255.0
Default gateway : 192.168.0.1
To access the camera, the IP address of the PC should
be 192.168.0.XXX (where XXX should be a number
from 2 to 254 except 10).
Note:The procedure described below is based on the
assumption that Windows...

-17- 7. Click the Use the following IP address radio button
and enter the IP address and the subnet mask as
follows.
IP address : 192.168.0.9
Subnet mask : 255.255.255.0
8. Click the [OK] button, and the window dialog box
closes.
Note:Use a small sized picture when a blue picture
appears instead of the live picture due to Internet
traffic congestion.
■Network Setup of the Camera
●Using Panasonic IP Setup Software
Set up the network of the camera using the Panasonic
IP Setup software included on the...

-18- 5. Click the [Enable] button when using DHCP and
DNS.
When using the DNS functions, enter the Primary
DNS Server address and the Secondary DNS
Server address.
6. Click [AUTO] when the DNS server gets primary and
secondary IP addresses from the DHCP server.
Notes:
•If DHCP is enabled although there is no DHCP
server in the network, check Disable for DHCP
in the Panasonic IP Setup window.
•If DHCP is enabled, and the DHCP server has
not assigned an IP address yet, 0.0.0.0 is dis-
played for the IP...

-19- 5. Enter admin in the user name line.
Note:The default setting is admin. The administra-
tor should change the user name and password
in the User Setup menu.
6. Click the [OK] button. The Setup Menu window
opens.
7. Click the [Network] button. The Network Setup win-
dow appears.
8. Enter parameters for each item in the columns.
Refer to Network Setup Parameters vs. Connection
Type.
Notes:
•After clicking the SET & REBOOT button, the
browser software stops refreshing images and
displays a dialog box...

-20- This section describes the camera setup procedures
common to accesses from the PC and from the camera. 
■Buttons Used for Setup
Press the buttons inside the camera, or click the but-
tons on the computer display. Each button is assigned
functions in the setup as follows.
qMenu ON/OFF button:Opens or closes the setup
menu,
wSET button:Validates the selection, opens a
detailed menu.
SET button: (Inside the camera)
To open the setup menu, hold down this for 2 sec-
onds.
To close the setup menu, move...