Panasonic Wv Np502 Operating Instructions Manual

							61
Configuration of the settings relating to the mail notification [Notific\
ation]
Click the [Notification] tab on the Alarm page. (pages 20 and 21: How to display/operate the setup menu)
The settings relating to the alarm mail can be configured. It is necessa\
ry to configure the settings of the mail server
to perform the mail notification. ( page 69)
Mail notification
[Mail server >>]
When Mail server >> is clicked, the [Mail] tab of the
Server page will be displayed. ( page 69)
[Mail notification]
Select On or Off to determine whether or not to pro-
vide notification by e-mail according to the settings for
the Alarm and Diag. checkboxes of Destination of
notification below. • When an alarm is detected (Alarm)
• When a notification of the remaining capacity of theSD memory card has been provided (Diag.)
• When the SD memory card has become full (Diag.)
• When the SD memory card cannot be recognized (Diag.)
Default: Off
[Alarm image attachment]
Select On or Off to determine whether or not to
attach an image to the mail to be sent when an alarm is
detected.
Default: Off
Note:
• The settings for Image capture size of the Alarm image section on the [Alarm] tab ( page 55) will
be applied to the size of the image to be attached.
 Destination of notification
[Address 1] - [Address 4]
Enter the destination mail address. Up to 4 destination
addresses can be registered.
Alarm checkbox: When the checkbox is checked,
the mail notification will be performed upon an alarm
occurrence.
Diag. checkbox: When the checkbox is checked,  the
mail notification will be provided in the following
cases. • When notification of the remaining capacity ofthe SD memory card has been provided
• When the SD memory card has become full
• The SD memory card cannot be recognized
Destination address :Enter the destination address. 
To delete the registered address, click the [Delete] but-
ton respective to the desired address.
Available number of characters: 3 - 128 characters
[Mail subject]
Enter the mail subject.
Available number of characters: 0 - 50 characters
[Mail body]
Enter the mail body.
Available number of characters: 0 - 200 characters
Note:
When the SD memory card becomes full, notification
mail will be sent with the following message. • When the SD memory card has become full:The SD memory card is full.
• When mounting of the SD memory card failed: The SD memory card cannot be recognized.
Step 6
Click the [Set] button. → The edited settings will be applied. 
						

							62
Configure the settings relating to Panasonic alarm protocol [Notificatio\
n]
Click the [Notification] tab on the Alarm page. (pages 20 and 21: How to display/operate the setup menu)
The settings relating to Panasonic alarm protocol can be configured in t\
his section.
 Panasonic alarm protocol notification
[Panasonic alarm protocol]
Select On or Off to determine whether or not to pro-
vide notification by Panasonic alarm protocol according
to the settings for the Alarm and Diag. checkboxes of 
Destination of notification below.
• When an alarm is detected (Alarm)
• When a notification of the remaining capacity of theSD memory card has been provided (Diag.)
• When the SD memory card has become full (Diag.)
• When the SD memory card cannot be recognized (Diag.)
Default: Off
Note:
• When On is selected, notification of the alarm occurrence will be provided to the registered desti-
nation addresses in order (to IP address 1 first, to IP
address 8 last).
[Destination port]
Select a destination port for the Panasonic alarm proto-
col from the following.
Available range: 1 - 65 535
Default: 1 818
[Retry times]
Select a retry time for the Panasonic alarm protocol.
Available range: 0 - 30
Default: 2
Destination of notification
[Address 1] - [Address 8]
Enter the destination IP address of the Panasonic alarm
protocol from the following. Host name is unavailable for
the IP address. Up to 8 destination addresses can be
registered.
Alarm checkbox: When the checkbox is checked,
the Panasonic alarm notification will be provided
upon an alarm occurrence.
Diag. checkbox: When the checkbox is checked,
notification using Panasonic alarm protocol will be
provided in the following cases. • When notification of the remaining capacity ofthe SD memory card has been provided
• When the SD memory card has become full
• The SD memory card cannot be recognized
Destination IP address: Enter the destination
address. 
To delete the registered IP address, click the [Delete]
button respective to the desired IP address.
Important: • Confirm that the destination IP addresses are regis- tered correctly. When a registered  destinationdoes
not exist, notification may be delayed. 
						

							63
Configure the setting relating to the image recog-
nition [Advanced func. ]
The setting relating to the XML notification, destinations of informatio\
n about the face detection and the settings
relating to the face detection can be configure on the Advanced func. page.
The Advanced func. page has 2 tabs; the [XML notification] tab and the [Face detection] tab\
.
Configure the settings relating to the XML notification [XML notificatio\
n]
Click the [XML notification] tab on the Advanced func. page.
The settings relating to the XML notification can be configured in this \
section. The XML notification is a function to
notify a server or others of face detection information in the XML forma\
t. 
 XML notification
[XML notification]
Select On or Off to determine whether or not to notify
face detection information using XML. 
Default: Off
[Notification interval]
Select 1s or 2s for the notification interval.
Default: 1s 
						

							64
Configuration of the destination settings of the face detection [XML not\
ifi-
cation]
Click the [XML notification] tab on the Advanced func.page.
The settings relating to the XML notification can be configured. The XML\
 notification is the function notifies of a serv-
er, etc. face detection information in XML format.
 Destination setting for XML notification
[Destination 1 ] [Destination 2 ] [Destination address ]
Configure the IP address or host name of the destina-
tion for XML notification of the face detection informa-
tion.
[Destination port number ]
Configure the port number settings for XML notification
of the face detection information.
[Destination path name ]
Configure the settings for the destination directory to be
used for the XML notification of the face detection.
[User name]
Enter a user name.
Available number of characters: 0 - 32 characters
Default: None (blank)
[Password]
Enter a password.
Available number of characters: 0 - 32 characters
Default: None (blank) 
						

							65
Configuration of the settings relating to the face detection [Face detec\
tion]
Click the [Face detection] tab on the Advanced func.page.
The settings relating to displaying the frame to be used for the face detection and the settings relating to  theface
detection information attached to the image can be configured.
Important:
• The face detection function shall not guarantee the detection of faces i\
n an image. The face detection accuracy varies with imaging conditions. 
 Face detection
[Face detection]
Determine whether or not to enable the face detection
function.
On: Information about the face detection frame will be
attached and the test frame will be displayed on the
image of this page.
Off: Information about the face detection frame will not
be attached. No face detection frame will be dis-
played on the image of this page.
Default: Off
Important:
• When Mosaic is selected for Display type of Privacy zone, the face detection function may
sometimes be triggered (the face detection frame
will be displayed). 
[XML notification]
The destination settings of the face detection informa-
tion can be configured.
When clicking XML notification, the [XML notification]
tab will be displayed. ( page 64) 
						

							66
Configure the settings relating to the authentica-
tion [User mng.]
The settings relating to the authentication such as users and PCs restri\
ctions for accessing the camera can be con-
figured on the User mng. page. 
The User mng. page has 3 tabs; the [User auth.] tab, the [Host auth.] \
tab and the [System] tab.
Configure the settings relating to the user authentication [User auth.]
Click the [User auth.] tab on the User mng. page. (pages 20 and 21: How to display/operate the setup menu)
The settings relating to the user authentication can be configured on th\
is page. Up to  18users can be registered.
Note:
• When user authentication (authentication error) has failed to pass 8 t\
imes within 30 seconds using the same IP address (PC), access to the camera will be denied for a while.
[User auth.]
Select On or Off to determine whether or not to
authenticate the users.
Default: Off
[User name]
Enter a user name.
Available number of characters: 1 - 32 characters
Default: None (blank)
[Password] [Retype password]
Enter a password.
Available number of characters: 4 - 32 characters
Default: None (blank)
Note:
• When the user name already in use is entered and the [Set] button is clicked, the respective user infor-
mation will be overwritten.
[Access level]
Select the access level of the user from the following.
1. Administrator: Allowed all available operations of
the camera.
2. Camera control: Allowed to display images from the
camera and to control the camera. The camera set-
ting configuration is unavailable.
3. Live only: Only displaying live images is available.
The camera setting configuration and camera con-
trol are unavailable.
Default: 3. Live only
[User check]
By clicking [C] of User check, the registered user can
be selected and the selected user’s information can be
checked. 
The registered user will be displayed with the access
level. (Example: admin [1])
To delete the registered user, click the [Delete] button
after selecting the user to be deleted. 
						

							67
Configure the settings relating to the host authentication [Host auth.]
Click the [Host auth.] tab on the User mng. page. (pages 20 and 21: How to display/operate the setup menu)
The restriction settings of PCs (IP address) from accessing the camera\
 can be configured on this page.
[Host auth.]
Select On or Off to determine whether or not to
authenticate the host.
Default: Off
[IP address]
Enter the IP address of the PC to be allowed to access
the camera. Host name cannot be entered for the IP
address.
Note: • When IP address/subnet mask is entered, it is pos- sible to restrict PCs in each subnet.
For example, when 192.168.0.1/24 is entered and
2. Camera control is selected for the access level,
the PCs whose IP address is between 192.168.0.0
- 192.168.0.255 can access the camera with the
access level 2. Camera control.
• When the IP address already in use is entered and the [Set] button is clicked, the respective host infor-
mation will be overwritten.
[Access level]
Select the access level of the host from the following.
1. Administrator/2. Camera control/3. Live only
Refer to page 66 for further information about the
access level.
Default: 3. Live only [Host check]
By clicking [C] of Host check, the registered host can
be selected and the selected host’s IP address can be
checked. 
The registered IP address will be displayed with the
access level. (Example:192.168.0.21 [1])
To delete the registered host, click the [Delete] button
after selecting the IP address to be deleted. 
						

							68
Configure the settings relating to the priority stream [System]
Click the [System] tab on the User mng. page. (pages 20 and 21: How to display/operate the setup menu)
The description below is the configuration of the priority stream that c\
an transmit images without deteriorating the
image quality and refresh interval even when multiple users access concu\
rrently.
 Priority stream
[Activation]
Select On or Off to determine whether or not to use
the priority stream.
Default: Off
Note:
• When On is selected for Activation of Priority stream, number of users who can access the cam-
era will be limited.
[Destination IP address (1)]
Enter the first destination IP address.
[Destination IP address (2)]
Enter the second destination IP address.
[Stream type]
Select either JPEG, H.264/MPEG-4(1) or H.264/
MPEG-4(2).
JPEG: JPEG images will be transmitted.
H.264/MPEG-4(1): H.264 (1) (or MPEG-4(1)) images
will be transmitted.
H.264/MPEG-4(2): H.264 (2) (or MPEG-4(2)) images
will be transmitted.
Default: JPEG
Note:
• JPEG is available only when  1.3 mega pixel is
selected for Image capture mode.
[Refresh interval*]
Select the refresh interval from the following. 
This setting is validated only when JPEG is selected
for Stream type.
0.1fps/0.2fps/0.33fps/0.5fps/1fps/2fps/3fps/5fps/6fps/
10fps/15fps */30fps *
Default:1fps
Note:
• When On is selected for H.264 (or MPEG-4) transmission, the transmission interval may be
longer than the set value when any value with an
asterisk (*) on the right is selected.
[Image capture size]
Select the image capture size from the following.
This setting is validated only when JPEG is selected
for Stream type.
QVGA/VGA/1280x960
Default: 1280x960 
						

							69
Configure the settings of the servers [Server]
[SMTP server address]
Enter the IP address or the host name of the SMTP
server used to send e-mails.
Available number of characters:1 - 128 characters
[SMTP port]
Enter the port number to which e-mails are sent.
Available port number: 1 - 65 535
Default: 25
[POP server address]
When POP before SMTP is selected for Type, enter
the IP address or the host name of the POP server.
Available number of characters: 1 - 128 characters
Important:
• When entering the host name for SMTP server address or POP server address, it is necessary to
configure the DNS settings on the [Network] tab of
the Network page. ( page 73)
[Authentication]
• Type
Select the authentication method to send e-mails from
the following.
None:It is not necessary to clear any authentication to
send e-mails.
POP before SMTP: It is necessary to first clear the
POP server authentication to use the SMTP server
to send e-mails.
SMTP: It is necessary to clear the SMTP server authen-
tication to send e-mails.
Default: None
Note:
• When you dont know the authentication method to send e-mails, refer to the network administrator.
• User name
Enter the user name to access the server.
Available number of characters: 0 - 32 characters
• Password
Enter the password to access the server. 
Available number of characters: 0 - 32 characters
[Senders mail address]
Enter the mail address of a sender.
The entered mail address will be displayed in the From
(sender) line of the sent mails.
Available number of characters: 3 - 128 characters
The settings relating to the mail server, the FTP server and the NTP ser\
ver can be configured on this page. 
The Server page has 3 tabs; the [Mail] tab, the [FTP] tab and the [NTP\
] tab.
Configure the settings relating to the mail server [Mail]
Click the [Mail] tab on the Server page. (
pages 20 and 21: How to display/operate the setup menu)
The settings relating to the mail server used to send the alarm mail can\
 be configured on this page.
Important: • When a terminal that receives e-mails is not compatible with UTF-8 encod\
e, it is impossible to receive alarm mails correctly. 
						

							70
[FTP server address]
Enter the IP address or the host name of the FTP serv-
er.
Available number of characters:1 - 128 characters
Important:
• When entering the host name for FTP server address, it is necessary to configure the DNS set-
tings on the [Network] tab of the Network page. 
( page 73)
[User name]
Enter the user name (login name) to access the FTP
server.
Available number of characters: 1 - 32 characters
[Password]
Enter the password to access the FTP server.
Available number of characters: 0 - 32 characters
[Control port]
Enter a control port number to be used for the FTP serv-
er.
Available port number: 1 - 65 535
Default: 21 [FTP mode]
Select Passive or Active for the FTP mode. 
Normally, select Passive. When it is impossible to con-
nect after selecting Passive, try to connect after select-
ing Active.
Default:
Passive
Configure the settings relating to the FTP server [FTP]
Click the [FTP] tab on the Server page. ( pages 20 and 21: How to display/operate the setup menu)
The settings relating to the FTP server used to transmit the alarm image\
s can be configured on this page.