Panasonic Wv Np244 Network Operating Instructions Manual

21
[About SD memory card]
Select Use or Not use to determine whether or not to
use the SD memory card. 
Important:
•Before removing the SD memory card from the cam-
era, it is necessary to select Not use first. 
• After inserting the SD memory card, it is necessary
to select Use to use the SD memory card. 
[Notification for SD memory card]
When the E-mail notification function or the
Panasonic alarm protocol function is used to notify of
the remaining space of the SD memory card, select a
timing to be...

22
Configure the settings relating to images and audio [Camera
setup]
The settings relating images and audio such as brightness and image qual\
ity of JPEG/MPEG-4 can configured on
this page. 
The Camera setup page has 3 tabs of the [JPEG/MPEG-4] tab, the [Camera\
] tab and the [Audio] tab. 
Configure the settings relating to JPEG image [JPEG/MPEG-4]
Click the [JPEG/MPEG-4] tab on the Camera setup page. (☞page 16)
Configure the settings such as Refresh interval (JPEG), Image captu\
re size and Image...

23
Configure the settings relating to MPEG-4 image [JPEG/MPEG-4]
Click the [JPEG/MPEG-4] tab on the Camera setup page. (☞page 16)
Configure the settings such as Refresh interval (MPEG-4), Image cap\
ture size and Image quality on this page.
Refer to page 22 for further information about the settings relating to \
JPEG images. 
[MPEG-4 transmission]
Select ON or OFF to determine whether or not to
transmit MPEG-4 images. 
ON:Transmits MPEG-4 images. 
OFF:Does not transmit MPEG-4 images. 
Default:ON
Note:...

[Multicast port]
Enter the multicast port number (used to transmit
MPEG-4 images from the camera). 
Available port number:1024 - 50000 (Only even num-
bers are available.)
Default:37004
[Multicast TTL]
Enter the multicast TTL value. 
Available value:1 - 254
Default:16
Important:
• Depending on the PC in use for monitoring, the mul-
ticast port number may be already in use. In this
case, it may be impossible to monitor images.
Change the multicast port number. 
•W hen transmitting MPEG-4 image via a...

25
Configure the camera settings such as image quality and brightness, etc.\
 [Camera]
Click the [Camera] tab on the Camera setup page. (☞page 16)
The following are descriptions of how to configure the settings relating\
 to images such as brightness, etc. 
[Brightness]
17 steps (–8 - 8) are available for brightness. –8 is the
darkest and 8 is the brightest. 
Default:0
[White balance]
Select the white balance adjustment method from the
following. 
AUTO:Adjusts the white balance automatically. 
HOLD:Fixes...

26
Configure the settings relating to audio [Audio]
Click the [Audio] tab on the Camera setup page. (☞page 16)
The settings relating to audio can be configured on this page. 
[Mic mode*]
Select ON or OFF to determine whether to turn on or
off audio on a PC. 
ON:Transmits audio from the camera to the PC. Audio
can be heard with images on the PC. Images and
audio will not be synchronized. 
OFF:Does not transmit audio from the camera to the
PC. Therefore, no settings and controls relating
audio will be...

27
Configure the multi-screen settings [Multi-screen setup]
The cameras to be used for the multi-screen display can be registered on\
 this page. 
Refer to page 16 for descriptions of how to display Multi-screen setup\
 page. 
Note:
The following cameras are available for the multi-screen display (as of\
 April 2006).
WV-NP1004, WV-NP244, WV-NP472, WV-NS324, WV-NW474S
[IP address]
Enter the IP address or the host name of the camera to
be used for the multi-screen. 4 cameras can be regis-
tered as a group...

28
Configure the alarm settings [Alarm setup]
The settings relating to alarm occurrences such as settings for the alar\
m action at an alarm occurrence, the alarm
occurrence notification, and the VMD area settings can be configured on \
this page. 
The Alarm setup page has 3 tabs of the [Alarm] tab, the [VMD area] tab\
 and the [Notification] tab. 
Configure the settings relating to the alarm action [Alarm]
Click the [Alarm] tab on the Alarm setup page. (☞page 16)
The settings relating to the alarm...

29
Configure the settings relating to the alarm image [Alarm image setup]
Click the [Alarm] tab on the Alarm setup page. (☞page 16)
The settings relating to the alarm image to be transmitted to the FTP se\
rver can be configured on this page. The
alarm image will be transmitted to the FTP server. To transmit alarm ima\
ges to the FTP server, it is necessary to
configure the settings in advance. (
☞page 38)
Refer to pages 28 and 30 for further information about the settings rela\
ting to the alarm action...

30
Configure the settings relating to the alarm out connector [Alarm output\
 setup]
Click the [Alarm] tab on the Alarm setup page. (☞page 16)
The settings relating to the alarm out connector can be configured on th\
is page. Refer to pages 28 and 29 for further
information about the settings relating to the alarm action and the alar\
m image. 
[Alarm output setup]
Select ON or OFF to determine whether or not to
output the alarm signals to the alarm out connector
when an alarm is detected. 
Default:OFF...