Panasonic Wv Np1004 Operating Instructions Manual

61
Adjust white balance finely
After adjusting white balance using the auto tracking white balance (AT\
W) function or the auto white balance control
(AWC) function (
☞page 53), manually adjust white balance finely.
Step 1
Press the [SET] button after selecting any of ATW1,
ATW2 and AWC for WHITE BAL on the CAMERA
SETUP page.
→The fine adjustment window will be displayed.
Step 2
Move the cursor onto R or B and adjust the level
using the [Left] and [Right] buttons. R indicates red
and B indicates blue....

62
Configure the B/W mode settings
Configure the settings relating to the B/W mode such as brightness at ch\
ange between color and B/W, waiting time
to change to the B/W mode, etc. It is possible to avoid frequent switche\
s between color and B/W by adjusting the
parameter of LEVEL and DURATION TIME.
Step 1
Press the [SET] button after moving the cursor onto
BW MODE on the CAMERA SETUP page.
→The BW MODE page will be displayed.
Step 2
Move the cursor onto BW and select a parameter from
the following....

63
Set the privacy zone
When there is a zone that is not to be displayed, set the zone as a priv\
acy zone to not to display.
Up to 8 privacy zones can be set.
Step 1
Move the cursor onto PRIVACY ZONE on the CAM-
ERA SETUP page and press the [SET] button after
selecting ON (1) or ON (2).
→The zone number selection page will be displayed.
Step 2
Confirm that the cursor is on 1 of 1/8 displayed on
the top of the page, and then press the [Left] button or
[Right] button to select the desired zone number....

64
Step 1
Select ON for EL-ZOOM on the CAMERA SETUP
page.
→The EL-ZOOM page will be displayed.
Step 2
Move the cursor onto ZOOM and press the [SET] but-
ton.
→Images to which zooming can be applied will be dis-
played.
Step 3
Adjust zooming level pressing the [Up] and [Down] but-
tons. After completing the adjustment, press the [SET]
button.
→The EL-ZOOM page will be displayed.
Step 4
Move the cursor onto PAN/TILT and press the [SET]
button.
→Images to which panning/tilting can be applied will
be...

65
Correct image defects (blemishes) such as scratches
Image defects (blemishes) such as scratches can be corrected in the fo\
llowing method.
Step 1
Press the [SET] button after moving the cursor onto
PIX OFF on the SPECIAL SETUP page.
→The PIX OFF page will be displayed.
Step 2
Press the [SET] button after selecting a number (1 – 16)
to be registered as a blemish compensation point.
→The blemish compensation point setting window will
be displayed.
Step 3
Press the [SET] button after moving the cross...

66
About the Displayed System Log
Error indications relating to SMTP
Category
POP3 server error
SMTP server error
Internal errorAuthentication error
Cannot connect to POP3 server
Authentication error
Other error Connection error to DNS server
Cannot connect to SMTP server.
Entered user name or password may be
incorrect. Check if the mail settings are con-
figured correctly.
•The IP address of the server may be
incorrect. Check if the IP address of the
server is configured correctly.
• The POP3 server may...

67
Category
Connection error
Connection error
Time adjustment 
synchronizing with NTP
succeeded. Internal error Internal errorCannot connect to DDNS server.
Cannot connect to NTP server.
Succeeded in the update. (NTP) Other error User name and password isnt correct.
IP address updated failed.
Other error •
The designated IP address of the DDNS
may be incorrect. Check if the DDNS set-
tings are configured correctly. 
• The DDNS server may be down. Ask the
network administrator.
• The IP address of the...

68
Troubleshooting
Before asking for repairs, check the symptoms with the following table
Contact your dealer if a problem cannot be solved even after checking an\
d trying the solution or if the problem is not
described below.
•Is the LAN cable (category 5) is firmly connected to
the network connector on the rear of the camera?
•Is the link LED right by the network connector lit? 
When it is not lit, connection to a LAN may not be
established or a network may be not working correct-
ly. Check if the...

69
•Is the power of the camera on?
Check if the power of the camera is turned on.
•Is the viewer software installed on a PC?
Install the viewer software on a PC.
•Aren’t there dusts or dirt on the lens?
Check if there are dust or dirt on the lens.
•Depending on the version of your browser, there
might be difficulties refreshing the picture and operat-
ing the camera.
It is recommended to use Internet Explorer 6.0 SP2.
•Is the SD memory card inserted correctly?
•Is the SD memory card formatted?
•Isn’t the...

70
•Isn’t the SD memory card out of order?
There are limited times to overwrite on an SD memory
card. When frequently overwritten, it may be at the
end of product life. It is recommended to replace the
SD memory card. 
•Is the camera used under fluorescent lamps operating
at 50 Hz?
By setting the shutter speed to 1/50 or 1/100, flick-
er caused by fluorescent lamps can be diminished.
•Isn’t the Scan mode set to Full scan?
When the selected scan mode is Full scan, the
frame rate of the analog output will...