Panasonic Wv Np1004 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Wv Np1004 Operating Instructions Manual. The Panasonic manuals for Camera are available online for free. You can easily download all the documents as PDF.
Page 41
![Page 41
41
Configuring the network settings [Network setup]
The network settings and the settings relating to DDNS (Dynamic DNS) a\
nd SNMP (Simple Network management
Protocol) can be configured on this page.
The Network setup page has 3 tabs of the [Network] tab, the [DDNS] tab\
, the [SNMP] tab and the [FTP] tab.
Configure the network settings [Network]
Click the [Network] tab on the Network setup page.
The following information is required to configure the network settings.\
Contact the network...](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-40.png "Page 41
41
Configuring the network settings [Network setup]
The network settings and the settings relating to DDNS (Dynamic DNS) a\
nd SNMP (Simple Network management
Protocol) can be configured on this page.
The Network setup page has 3 tabs of the [Network] tab, the [DDNS] tab\
, the [SNMP] tab and the [FTP] tab.
Configure the network settings [Network]
Click the [Network] tab on the Network setup page.
The following information is required to configure the network settings.\
Contact the network...")
41 Configuring the network settings [Network setup] The network settings and the settings relating to DDNS (Dynamic DNS) a\ nd SNMP (Simple Network management Protocol) can be configured on this page. The Network setup page has 3 tabs of the [Network] tab, the [DDNS] tab\ , the [SNMP] tab and the [FTP] tab. Configure the network settings [Network] Click the [Network] tab on the Network setup page. The following information is required to configure the network settings.\ Contact the network...
Page 42
![Page 42
42
[Default gateway]
When not using the DHCP function, enter the default
gateway of the camera.
Default:192.168.0.1
0.*.*.*
*.*.*.0
255.*.*.*
*.*.*.255
127.0.0.1
Class D address (224.0.0.0 - 239.255.255.255)
Class E address (240.0.0.0 - 255.255.255.255)
Note:
These IP addresses for the default gateway are
unavailable even when using the DHCP function.
Refer to the network administrator for the settings of
the DHCP server.
[HTTP port]
Assign the port numbers independently.
The following port numbers...](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-41.png "Page 42
42
[Default gateway]
When not using the DHCP function, enter the default
gateway of the camera.
Default:192.168.0.1
0.*.*.*
*.*.*.0
255.*.*.*
*.*.*.255
127.0.0.1
Class D address (224.0.0.0 - 239.255.255.255)
Class E address (240.0.0.0 - 255.255.255.255)
Note:
These IP addresses for the default gateway are
unavailable even when using the DHCP function.
Refer to the network administrator for the settings of
the DHCP server.
[HTTP port]
Assign the port numbers independently.
The following port numbers...")
42 [Default gateway] When not using the DHCP function, enter the default gateway of the camera. Default:192.168.0.1 0.*.*.* *.*.*.0 255.*.*.* *.*.*.255 127.0.0.1 Class D address (224.0.0.0 - 239.255.255.255) Class E address (240.0.0.0 - 255.255.255.255) Note: These IP addresses for the default gateway are unavailable even when using the DHCP function. Refer to the network administrator for the settings of the DHCP server. [HTTP port] Assign the port numbers independently. The following port numbers...
Page 43
![Page 43
43
Notes:
•The port forwarding function changes a global IP address to a private IP\
address, and Static IP masquerade
and Network Address Translation (NAT) have this function. This funct\
ion is to be set in a router.
• To access the camera via the Internet by connecting the camera to a broa\
dband router, it is necessary to assign
a respective port number for each camera and address translation by usin\
g the port forwarding function. For fur-
ther information, refer to the operating instructions of...](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-42.png "Page 43
43
Notes:
•The port forwarding function changes a global IP address to a private IP\
address, and Static IP masquerade
and Network Address Translation (NAT) have this function. This funct\
ion is to be set in a router.
• To access the camera via the Internet by connecting the camera to a broa\
dband router, it is necessary to assign
a respective port number for each camera and address translation by usin\
g the port forwarding function. For fur-
ther information, refer to the operating instructions of...")
43 Notes: •The port forwarding function changes a global IP address to a private IP\ address, and Static IP masquerade and Network Address Translation (NAT) have this function. This funct\ ion is to be set in a router. • To access the camera via the Internet by connecting the camera to a broa\ dband router, it is necessary to assign a respective port number for each camera and address translation by usin\ g the port forwarding function. For fur- ther information, refer to the operating instructions of...
Page 44
![Page 44
44
[User name]
Enter the user name (login name) to access the DDNS
server.
Number of characters for the user name:1 - 32 char-
acters
[Password]
Enter the password to access the DDNS server.
Number of characters for the password:0 - 32 char-
acters
[Access interval]
Select the interval to access the DDNS server to check
the IP address and the host name from the following.
1 min/10 min/30 min/1 hour/6 hours/24 hours
Default:1 hour
Configure the settings relating to SNMP [SNMP]
Click the [SNMP] tab on...](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-43.png "Page 44
44
[User name]
Enter the user name (login name) to access the DDNS
server.
Number of characters for the user name:1 - 32 char-
acters
[Password]
Enter the password to access the DDNS server.
Number of characters for the password:0 - 32 char-
acters
[Access interval]
Select the interval to access the DDNS server to check
the IP address and the host name from the following.
1 min/10 min/30 min/1 hour/6 hours/24 hours
Default:1 hour
Configure the settings relating to SNMP [SNMP]
Click the [SNMP] tab on...")
44 [User name] Enter the user name (login name) to access the DDNS server. Number of characters for the user name:1 - 32 char- acters [Password] Enter the password to access the DDNS server. Number of characters for the password:0 - 32 char- acters [Access interval] Select the interval to access the DDNS server to check the IP address and the host name from the following. 1 min/10 min/30 min/1 hour/6 hours/24 hours Default:1 hour Configure the settings relating to SNMP [SNMP] Click the [SNMP] tab on...
Page 45
![Page 45
45
Configure the settings relating to the FTP periodic transmission [FTP pe\
riodic
transmission]
Click the [FTP] tab on the Network setup page. (☞page 41)
The settings relating to the periodic transmission of images to an FTP s\
erver can be configured on this page. To
transmit images to an FTP server periodically, it is necessary to config\
ure the settings of the FTP server in advance.
(
☞page 40)
Refer to page 47 for descriptions of how to configure schedules of image\
transmission.
Important:
•...](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-44.png "Page 45
45
Configure the settings relating to the FTP periodic transmission [FTP pe\
riodic
transmission]
Click the [FTP] tab on the Network setup page. (☞page 41)
The settings relating to the periodic transmission of images to an FTP s\
erver can be configured on this page. To
transmit images to an FTP server periodically, it is necessary to config\
ure the settings of the FTP server in advance.
(
☞page 40)
Refer to page 47 for descriptions of how to configure schedules of image\
transmission.
Important:
•...")
45 Configure the settings relating to the FTP periodic transmission [FTP pe\ riodic transmission] Click the [FTP] tab on the Network setup page. (☞page 41) The settings relating to the periodic transmission of images to an FTP s\ erver can be configured on this page. To transmit images to an FTP server periodically, it is necessary to config\ ure the settings of the FTP server in advance. ( ☞page 40) Refer to page 47 for descriptions of how to configure schedules of image\ transmission. Important: •...
Page 46
![Page 46
46
[Interval]
Select the interval for the FTP periodic transmission
from the following.
1 sec/2 sec/3 sec/4 sec/5 sec/6 sec/10 sec/15 sec/
20 sec/30 sec/1 min/2 min/3 min/4 min/5 min/6 min/
10 min/15 min/20 min/30 min/1 hour/1.5 hours/2 hours/
3 hours/4 hours/6 hours/12 hours/24 hours
Default:1 sec
[Image capture size]
Select an image capture size of images to be transmit-
ted to the FTP server from the following according to the
selected scan mode.
When Full scan is selected for the scan mode
1280 x...](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-45.png "Page 46
46
[Interval]
Select the interval for the FTP periodic transmission
from the following.
1 sec/2 sec/3 sec/4 sec/5 sec/6 sec/10 sec/15 sec/
20 sec/30 sec/1 min/2 min/3 min/4 min/5 min/6 min/
10 min/15 min/20 min/30 min/1 hour/1.5 hours/2 hours/
3 hours/4 hours/6 hours/12 hours/24 hours
Default:1 sec
[Image capture size]
Select an image capture size of images to be transmit-
ted to the FTP server from the following according to the
selected scan mode.
When Full scan is selected for the scan mode
1280 x...")
46 [Interval] Select the interval for the FTP periodic transmission from the following. 1 sec/2 sec/3 sec/4 sec/5 sec/6 sec/10 sec/15 sec/ 20 sec/30 sec/1 min/2 min/3 min/4 min/5 min/6 min/ 10 min/15 min/20 min/30 min/1 hour/1.5 hours/2 hours/ 3 hours/4 hours/6 hours/12 hours/24 hours Default:1 sec [Image capture size] Select an image capture size of images to be transmit- ted to the FTP server from the following according to the selected scan mode. When Full scan is selected for the scan mode 1280 x...
Page 47
![Page 47
47
Configure the schedule settings of the FTP periodic transmission [Schedu\
le
setup]
Click the [FTP] tab on the Network setup page. (☞page 41)
The schedule settings of the FTP periodic transmission can be configured\
on this page. Refer to page 45 for further
information about the settings relating to the FTP periodic transmission\
.
How to configure the schedule settings
Step 1
Check the check box of the desired day of the week.
→The selected day of the week will be validated for
the schedule.
Step...](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-46.png "Page 47
47
Configure the schedule settings of the FTP periodic transmission [Schedu\
le
setup]
Click the [FTP] tab on the Network setup page. (☞page 41)
The schedule settings of the FTP periodic transmission can be configured\
on this page. Refer to page 45 for further
information about the settings relating to the FTP periodic transmission\
.
How to configure the schedule settings
Step 1
Check the check box of the desired day of the week.
→The selected day of the week will be validated for
the schedule.
Step...")
47 Configure the schedule settings of the FTP periodic transmission [Schedu\ le setup] Click the [FTP] tab on the Network setup page. (☞page 41) The schedule settings of the FTP periodic transmission can be configured\ on this page. Refer to page 45 for further information about the settings relating to the FTP periodic transmission\ . How to configure the schedule settings Step 1 Check the check box of the desired day of the week. →The selected day of the week will be validated for the schedule. Step...
Page 48
![Page 48
48
How to delete the set schedule
Step 1
Uncheck the check box of the set day of the week.
Step 2
Click the [SET] button after completing the settings.
→The result will be displayed at the bottom of the win-
dow.](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-47.png "Page 48
48
How to delete the set schedule
Step 1
Uncheck the check box of the set day of the week.
Step 2
Click the [SET] button after completing the settings.
→The result will be displayed at the bottom of the win-
dow.")
48 How to delete the set schedule Step 1 Uncheck the check box of the set day of the week. Step 2 Click the [SET] button after completing the settings. →The result will be displayed at the bottom of the win- dow.
Page 49
![Page 49
49
Maintenance of the camera [Maintenance]
System log check, firmware upgrade, and initialization of the setup menu\
can be performed on this page.
The Maintenance page has 3 tabs of the [System log] tab, the [Upgrade]\
tab and the [Initialization] tab.
Check the system log [System log]
Click the [System log] tab of the Maintenance page.
Up to 4000 system logs can be saved on the SD memory card when the SD me\
mory card is inserted after selecting
Use for About the SD memory card on the [SD memory...](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-48.png "Page 49
49
Maintenance of the camera [Maintenance]
System log check, firmware upgrade, and initialization of the setup menu\
can be performed on this page.
The Maintenance page has 3 tabs of the [System log] tab, the [Upgrade]\
tab and the [Initialization] tab.
Check the system log [System log]
Click the [System log] tab of the Maintenance page.
Up to 4000 system logs can be saved on the SD memory card when the SD me\
mory card is inserted after selecting
Use for About the SD memory card on the [SD memory...")
49 Maintenance of the camera [Maintenance] System log check, firmware upgrade, and initialization of the setup menu\ can be performed on this page. The Maintenance page has 3 tabs of the [System log] tab, the [Upgrade]\ tab and the [Initialization] tab. Check the system log [System log] Click the [System log] tab of the Maintenance page. Up to 4000 system logs can be saved on the SD memory card when the SD me\ mory card is inserted after selecting Use for About the SD memory card on the [SD memory...
Page 50
![Page 50
50
Upgrade the firmware [Upgrade]
Click the [Upgrade] tab of the Maintenance page. (☞page 49)
The current firmware can be checked and upgraded to the latest version o\
n this page. Contact the dealer for further
information about the firmware upgrade.
[Model No.], [MAC address], [Firmware version],
[IPL version], [DSP version]
Information of each item will be displayed.
How to upgrade the firmware
Step 1
Contact the dealer and download the latest firmware
onto a PC.
Important:
A blank (space) cannot be...](http://img.usermanuals.tech/thumb/58/68505/w300_wv-np1004-network_en_om_d-49.png "Page 50
50
Upgrade the firmware [Upgrade]
Click the [Upgrade] tab of the Maintenance page. (☞page 49)
The current firmware can be checked and upgraded to the latest version o\
n this page. Contact the dealer for further
information about the firmware upgrade.
[Model No.], [MAC address], [Firmware version],
[IPL version], [DSP version]
Information of each item will be displayed.
How to upgrade the firmware
Step 1
Contact the dealer and download the latest firmware
onto a PC.
Important:
A blank (space) cannot be...")
50 Upgrade the firmware [Upgrade] Click the [Upgrade] tab of the Maintenance page. (☞page 49) The current firmware can be checked and upgraded to the latest version o\ n this page. Contact the dealer for further information about the firmware upgrade. [Model No.], [MAC address], [Firmware version], [IPL version], [DSP version] Information of each item will be displayed. How to upgrade the firmware Step 1 Contact the dealer and download the latest firmware onto a PC. Important: A blank (space) cannot be...