Panasonic Wireless PT-LB50NTE/PT-LB55NTE/PT-LB60NTE, PT-LB50NTU/PT-LB60NTU Instruction Manual

							
11

Software Installation (cont.)
This  CD-ROM  includes  DirectX  9.0c.  To  transfer  moving  picture  using  the  projector, 
your computer must have DirectX 8.1b or newer.
Click [DirectX 9.0c] on page 10.
The License Agreement for DirectX appears.1
Place a check in the [I accept the 
agreement] checkbox and click 
[Next].
The  DirectX  Runtime  component  install  window 
appears.
2
Click [Next].
•  The  DirectX  component  install  progress  bar 
appears.
•  Do  not  perform  any  other  operations  until 
installation is complete.
3
Click [Finish] when the window to 
the right appears.4
DirectX 9.0c
• Once installed, the DirectX 9.0c Runtime cannot be uninstalled.
• DirectX  9.0c  is  already  installed  in  Windows  XP  SP  2,  so  there  is  no  need  to  install  it  again.  (How  to  check  the  version  of  installed  DirectX  :  Click  [start]→[Run],  input 
[dxdiag], and click [OK]. [DirectX Diagnostic Tool] dialogue box appears, then you can 
confirm the [DirectX version] in [System Information] of [System] tab.)
•  In  rare  cases,  installing  DirectX  9.0c  may  prevent  your  computer  from  starting  up  properly.  Before  installing,  be  sure  to  verify  with  the  customer  support  office  of  the 
manufacturer that the video card of your computer is compatible with DirectX 9.0c.
•  No guarantees are made for the operation of Wireless Manager ME 3.0 with a version 
newer than DirectX 9.0c. 
						

							
12

Installation free Wireless Manager ME 3.0 set up
You can use Wireless Manager ME 3.0 without installing it in the computer.
If  you  copy  Wireless  Manager  ME  3.0  to  a  removable  medium,  such  as  an  SD  card, 
you can use Wireless Manager ME 3.0 without installing it in any computer that permits 
you to access this removal medium.
Insert provided CD-ROM into the CD-ROM drive.
Setup screen appears.1
Click [Installation Free Set Up].
[Direct  CD-ROM  Startup]  and  [Other  Media  Source  Startup,  Make  Copy  Here] 
appear on the window.2
Select the destination to save, and click [OK].
CD-ROM data is copied to the destination. 
After the copy ends, click [End] of the setup screen.
4
Double-click the Wireless Manager ME 3.0 icon (WM.
exe) in the destination to save chosen in step 4.
Wireless Manager ME 3.0 starts up.
Operation is the same as when operating after installing CD-ROM.
If  selecting  removable  medium  as  the  destination  to  save,  ensure  that  the 
removable  medium  is  recognized  by  the  computer  to  which  you  wish  to 
connect the projector.
Some removable mediums start the program automatically.
5
• When using without installing, following functions are not available.• Selective area transmission (See page 35)
• Secondary display transmission (See page 36)
• Motion streaming mode (See page 38)
• Producing audio along with video at live mode
• Operation  is  slower  compared  to  when  the  computer  is  used  with  Wireless 
Manager ME 3.0 installed.
3A  When using Wireless Manager ME 3.0 without 
copying the program: Click [Direct CD-ROM 
Startup].
Wireless  Manager  ME  3.0  starts  up,  and  the  “Select Access  Port”  window 
appears.
Operation is the same as when operating after installing CD-ROM.
B When copying Wireless Manager ME 3.0 : Click 
[Other Media Source Startup, Make Copy Here].
A window opens to select the destination to save.
 
						

							
13

Connect
Select Access Port window
Click [] on the desktop, 
or select [Start] → [All Programs] → [Panasonic Wireless 
Display] → [Wireless Manager mobile edition 3.0].
Wireless Manager ME 3.0 starts up, and the “Select Access Port” window appears.
ƒ Network
When  you  specify  the  network  number 
(See  page  46)  set  on  the  projector  from 
one  of  [1],  [2],  [3],  [4],  and  [U  (USER)]
Þ1, 
projectors  that  are  presently  switched 
on  in  the  selected  network  number  are 
displayed  in  [Projector  Name].  The  initial 
value  for  both  the  computer  and  the 
projector is [1]Þ2.
Þ1-2 (See page 15)
ΠDesignate (See page 20)
Designate  projectors  to  be  connected  when 
ƒ  is set to [U].
 ID Search (See page 21)
When  you  click  [ID  Search],  a  search  for 
the projector of the specified ID is carried 
out  from  among  the  projectors  that  are 
presently  switched  on,  from  all  channels 
other than [U].
„ ID (See page 21)
Display projector’s ID
… Mode (See page 25)
Display projector’s mode or style
†  [] appears when password entry 
is needed for connection. (See page 
20)
‡ The status of this projector
ˆ  The number of people connected to  this projector.
‰  Access Devices
When  only  one  projector  is  connected, 
select  [
].  When  multiple  projectors  are 
connected, select [].
Š  Available mode and functions
Among  [Live  mode],  [Multi  live  mode], 
[ O n e   s h o t ] ,   a n d   [ M o t i o n   s t r e a m i n g ] , 
unavailable one is displayed with [
].
‹  Connectability
W h e n   y o u   c l i c k   [ C o n n e c t a b i l i t y ] ,   t h e 
projector  name  and  ID  are  displayed  at 
top  left  of  the  projector  screen.  If  the 
projector  name  and  ID  are  displayed 
c o r r e c t l y,   t h e   m e s s a g e   “ P r o j e c t o r   i s 
available.”  will  appear  on  the  computer 
screen.
‹Œ
ƒ„…‡ˆ‰Š†
 How to connect
• Easy Wireless Set Up (See page 14)
• When connecting without the administrator authority (See  page 17)
• Sending  data  by  wireless  transmission  while  the  projector  is  connected  to  the 
wireless LAN
(When connecting through the access point) (See page 19) 
						

							
14

Select the desired projectors, and click [OK].
The  launcher  shown  below  appears  and  the  connection  with  the  projector  is 
established. (“Description of the launcher” →See page 23)
The  launcher  always  appears  on  the  computer  screen,  and  can  be  used  to 
perform various operations.
The  launcher  appears  only  on  the  computer  screen  and  is  not  projected  by  the 
projector.
6
If  the  computer  has  built-in  wireless  LAN  or  has  a  wireless  LAN  card  installed,  the 
necessary  settings  will  be  made  automatically  when  Wireless  Manager  ME  3.0  is 
started.
Easy Wireless Set Up
Turn on the projector.1
Press the [WIRELESS] button on the remote control.
Input signal is switched to Wireless on the projector.
([INPUT  SELECT]  button  on  the  remote  control  or  [INPUT]  button  on  the 
projector are also available to switch input signals.)
2
Turn on the computer.3
Click [] on the desktop, 
or select [Start] → [All Programs] → [Panasonic Wireless 
Display] → [Wireless Manager mobile edition 3.0].
Wireless  Manager  ME  3.0  starts  up,  and  the  “Select  Access  Port”  window 
appears.
4
Select the network number of the desired projector 
from [Network].
Projectors powered on in the chosen network group are listed.
5
Connect (cont.) 
						

							
15

Connect (cont.)
•  Wireless  connection  cannot  be  made  between  the  projector  and  the  computer.  (See 
page 63)
•  Automatic connection setting (See page 44)
Þ1 • When  a  user  logs  on  a  computer  without  the  administrator  authority,  selectable 
network number is only [U].
• Depending  on  the  computer  and  wireless  LAN  card  used,  easy  wireless  set  up  may  not  be  possible.  If  this  is  the  case,  the  [Network]  setting  of  “Select  Access 
Port”  window  will  be  switched  to  [U]  automatically.  For  details  of  the  connection 
procedure, first close Wireless Manager ME 3.0, and then refer to pages 17-19.
Þ2• The  initial  network  number  for  both  the  projector  and  Wireless  Manager  ME  3.0  is  [1]. These numbers must match for the connection.
  To check the network number, refer to the wireless menu of the projector.
• When importance is placed on security, select the network number [2]-[4], because  WEP (wireless communication encryption) is set on these network numbers.
• Important video/audio data is protected because AES
Þ encryption processing takes 
place in advance for all network numbers, even if [ENCRYPTION] is set to [NONE].  
Þ “Glossary” (See page 62)
• O t h e r   n e t w o r k   a d a p t e r s   m a y   n o t   b e   u s a b l e   u n d e r   e a s y   w i r e l e s s   s e t   u p 
connections.
• Connections  to  other  networks  connected  through  the  wireless  LAN  card  are 
broken during easy wireless set up connections. 
						

							
16

Connect (cont.)
Connection error messages
One  of  the  following  windows  may  appear  when  a  wireless  connection  cannot  be 
made.
When a setting error for the wireless LAN card has been detected (See page 63)
• Is the wireless LAN card effective?
• Is your wireless LAN card properly recognized?
• Some  wireless  cards  may  allow  easy  wireless  set  up 
connections to function if drivers are updated.
When the Network Bridge setting has been detected (See page 64)
If  you  do  not  expect  ever  to  use  Network  Bridge  and  see 
no need for it, delete it from your system.
When Windows Firewall has been detected (See page 65)
• Has your firewall in Windows XP been disabled?
• I s   W i r e l e s s   M a n a g e r   M E   3 . 0   r e g i s t e r e d   i n  [Exceptions]  ([Control  Panel]  →  [Security  Center]  → 
[Windows firewall]) with the Windows XP SP 2?
When another firewall has been detected (See page 66)
Are any firewall-containing applications installed?
When the user does not have the administrator authority (Next page)
If  you  have  logged  onto  a  computer  as  a  [GUEST] 
or  a  restricted  user  who  does  not  have  administrator 
authority,  you  can  not  perform  easy  wireless  set  up 
(Network  No.  [1]  –  [4]).  If  you  must  perform  easy 
w i r e l e s s   s e t   u p   w i t h o u t   a d m i n i s t r a t o r   a u t h o r i t y, 
designate [U] as the network number.
When a change in the settings made by the utility has been detected 
The wireless LAN utility used by the computer may have 
changed the wireless settings. Close the utility, and then 
make  the  connection  again  using  easy  wireless  set  up 
connection. 
						

							
17

Connect (cont.)
Before  starting  Wireless  Manager  ME3.0,  it  is  necessary  to  carry  out  “Computer 
settings” („ on this page) under the administrator authority in advance.
Next, logon as a restricted user or [GUEST], and start Wireless Manager ME 3.0.
Confirm to your system administrator before changing any settings.
Following settings are examples of when using a default setting projector.
ƒ Projector settings Þ“Glossary” (See pages 61-62)
1Turn on the projector and press the [WIRELESS] 
button on the remote control.
2Select [USER 1]- [USER 3] from [NETWORK] at the 
wireless menu and press the [ENTER] button.
„ Computer settings
4Turn on the computer and log on with the administrator 
authority.
Click  [Start]  →  [Control  Panel]  →  [Network  and  Internet  Connections]  → 
[Network  Connections],  right  click  [Wireless  Network  Connections],  and  click 
[Properties], then [Wireless Network Connection Properties] window appears.
3Set the details of network and select [OK].
As for network setting items, see pages 49-52.
Confirm to your system administrator before changing any settings.

5Select [Internet Protocol (TCP/IPÞ)] on [General] tab, 
and click [Properties].
[Internet Protocol (TCP/IP) Properties] window appears.
DHCPÞOFF
IP ADDRESSÞ192.168.10.100
SUBNETMASKÞ255.255.255.0
SSIDÞPanasonic Projector
MODEAD HOCÞ
AUTHENTICATIONOPENÞ (Some computers may require connection by [SHAREDÞ] authentication.)
ENCRYPTIONNONE…When not performing encryption
WEP…When performing encryption
ENCRYPTION KEY
SETTING
When [ENCRYPTION]  setting is [WEPÞ]:
DEFAULT KEY : Set 1 – 4 numerals for the default key.
KEY 1 – 4  :  Set these to match the WEP key registered  in [DEFAULT KEY].
Connect without easy wireless set up
When logging on without administrator authority  
						

							
18

Connect (cont.)
If the projector is not displayed, click [Designate] followed by [ADD], then enter 
the IP address set in the projector using the “Access Port Registration” window, 
and click [REGISTER]. (See page 20)
8
Make the SSID, network authentication, data 
encryption and communication mode settings the 
same as those of step 3, and click [OK].
12Start Wireless Manager ME 3.0, and select [U] from 
[Network] of “Select Access Port” window.
13Select the desired projector, and click [OK].
The  launcher  appears  and  the  connection  with  the  projector  is  established. 
(“Description of the launcher” →See page 23)
9Click [OK] in [Wireless Network Connection Properties] 
window.
The connection with the projector is established.
10Click [Start]→[Log Off] and log off from the computer.
11Log on with the user who operates Wireless Manager 
ME 3.0.
7Click [Add] of [Preferred networks] on [Wireless 
Networks] tab in [Wireless Network Connection 
Properties] window.
[Wireless network properties] window appears.
… Computer operation
6
Select [Use the following IP address] on [General] tab, 
enter the IP address and Subnetmask, and click [OK].
Make  the  IP  addresses  of  the  upper  three  of  the  four  break  points  the  same 
value  as  that  of  the  projector,  and  change  the  value  of  the  last  break  point 
alone.
Make the Subnetmask as the same value as that of the projector. 
						

							
19

Connect (cont.)
You  can  make  the  setting  for  infrastructure  modeÞ  (connection  through  the  access 
point);  however,  confirm  to  your  system  administrator  on  network  settings  before 
changing any settings.
Þ“Glossary” (See page 62)
ƒ Projector settings
1Turn on the projector and press the [WIRELESS] 
button on the remote control.
2Select [USER 1]- [USER 3] from [NETWORK] at the 
wireless menu and press the [ENTER] button.
3
Set the details of network and select [OK].
As for network setting items, see pages 49-52.
Confirm to your system administrator on network settings before changing any 
settings.
„ Computer settings
4Turn on the computer.
5Make the network setting according to your system 
administrator.
6Connect to your access point.
If the projector is not displayed, click [Designate] followed by [ADD], then enter 
the IP address set in the projector using the “Access Port Registration” window, 
and click [REGISTER]. (See page 20)
7Start Wireless Manager ME 3.0, and select [U] from 
[Network] of “Select Access Port” window.
8Select the desired projector, and click [OK].
The  launcher  appears  and  the  connection  with  the  projector  is  established. 
(“Description of the launcher” →See page 23)
Connecting through the access point 
						

							
20

Connect (cont.)
Þ
“Glossary” (See page 61)
The  newly  registered  connection  is  added  to  the 
connection list in the window shown in step 1.
Click [ADD] and enter the IP addressÞ 
(including its periods) of the 
connection to be added, and then 
click [REGISTER].
2
Click [Designate] at the 
“Select Access Port” 
window.
The window shown to the right appears.
1
When  [Network]  is  set  to  [U]  and  the  desired  projector  is  not  displayed  at  the  “Select 
Access  port”  window,  connections  can  be  added  and  deleted  by  the  following 
operations.
 Adding a connection
When  a  projector  with  the  []  mark  is  selected,  the  window 
shown to the right appears. Enter the password and click [OK].
(See page 47)
 Deleting a connection
Select  the  connection  to  be  deleted  at  the  window  shown  in  step  1  and  click 
[DELETE].
Other operations for connection
• Click [CANCEL] at the password entry window to return to launcher (See page 23).
• When  an  incorrect  password  is  entered,  an  error  message  appears.  Click  [OK]  to 
return to the password entry window and enter the correct password again.
Operations when password entry is required for connection
Adding and deleting connections