Panasonic VW-CLT2 3D Conversion Lens Owners Manual

							11
(ENG)VQT4A75
2
Match the position of the convex C with the 
concave  D in the video camera.
≥Attach with the adjustment dial cover  E of the 3D 
Conversion Lens facing upwards.
≥ You cannot attach the 3D Conversion Lens together with the 
lens hood or a filter etc.




For a video camera with a filter diameter of 
46 mm
VQT4A75_P_eng__lsp.book  11 ページ  ２０１１年１２月１４日　水曜日　午後５時１分 
						

							12VQT4A75(ENG)3
Slide the attachment lever of the 3D 
Conversion Lens to LOCK while holding 
down the lock button of the attachment 
lever.
≥Slide the upper and lower attachment levers while 
pressing them down with your fingers.∫ Removing the 3D Conversion Lens
Slide the attachment lever to UNLOCK while 
holding down the lock button of the attachment 
lever.
LOCKLOCK
UNLOCKUNLOCK
VQT4A75_P_eng__lsp.book  12 ページ  ２０１１年１２月１４日　水曜日　午後５時１分 
						

							13
(ENG)VQT4A75
(For the video camera with a filter diameter of 46 mm)Tighten the attachment screw of the step up 
ring by rotating to LOCK.
≥ Be careful not to overtighten. If the 3D Conversion Lens is 
overtightened, you may not be able to remove it from the 
video camera.∫ Removing the 3D Conversion Lens
Rotate the attachment screw  of the step up ring to 
UNLOCK to loosen and then remove.≥ Place the video camera on a stable location such as a table, and be careful not to drop the 3D Conversion Lens. 
≥ Attach the 3D Conversion Lens securely so it will not tilt or move.
UNLOCK UNLOCK
LOCK
LOCK
VQT4A75_P_eng__lsp.book  13 ページ  ２０１１年１２月１４日　水曜日　午後５時１分 
						

							14VQT4A75(ENG)∫When not using the 3D Conversion 
Lens
Attach the lens rear cap to the 3D 
Conversion Lens and store it inside the 
supplied storage bag.≥ For users who have a video camera with a filter 
diameter of 46 mm, 3D Conversion Lens can be 
stored in the supplied storage bag with the step up 
ring attached.
Attach the lens rear cap of the step up ring and store 
it.
∫ Attaching/Detaching the lens front cap≥If you use the lens front cap as a stand as shown 
below, you can leave the video camera with the 3D 
Conversion Lens attached.≥Be careful not to lose the lens caps.
≥ When storing, always attach the lens caps to avoid 
scratching the protective panel.
VQT4A75_P_eng__lsp.book  14 ページ  ２０１１年１２月１４日　水曜日　午後５時１分 
						

							15
(ENG)VQT4A75
When using for the first time, be sure to adjust the 3D Conversion Lens attachment position.
≥Change the mode to 
 on the video camera
.
1
Attach the 3D Conversion Lens to the 
video camera. ( l10)
2
Turn on the video camera.
≥Turn on with the video camera in a horizontal state.
≥ The 3D Conversion Lens adjustment mode screen 
will appear automatically after performing the initial 
setting.
≥ If the 3D Conversion Lens adjustment mode 
screen does not appear automatically, set from 
the menu on the video camera.
([SETUP]  # [3D CONV. LENS SETUP])
3
Attach the lens front cap to the 3D 
Conversion Lens. ( l14)
A Guide Line
≥ The horizontal line for adjustment on the lens front 
cap is displayed on the screen.
≥ Perform the adjustment in a bright location where the 
horizontal line for adjustment will be clearly visible.4
Touch [ADJUST].
≥If the black vertical line and the black horizontal line 
are within the red guidelines  A and adjustment is not 
required, touch [EXIT] and proceed to Step 11.
Adjust the attachment position and record

VQT4A75_P_eng__lsp.book  15 ページ  ２０１１年１２月１４日　水曜日　午後５時１分 
						

							16VQT4A75(ENG)5
Open the adjustment dial cover.
≥When turning the adjustment dials, hold the video 
camera in the palm of your hand from the bottom and 
operate with the fingers of your other hand without 
applying too much force from above. When checking 
the adjustment, check with your fingers off the 
adjustment dials.
6
Adjust the horizontal position by 
rotating the horizontal image position 
adjustment dial   to place the black 
vertical line between the images at right 
and left in between the red guidelines 
A.
≥Touch [NEXT].

VQT4A75_P_eng__lsp.book  16 ページ  ２０１１年１２月１４日　水曜日　午後５時１分 
						

							17
(ENG)VQT4A75
7
Adjust the vertical position by rotating 
the vertical position adjustment dial   
so that the black horizontal line comes 
around the center of two red guidelines 
A.
≥Touch [NEXT].8
Remove the lens front cap.
≥After checking the operation description, touch 
[NEXT].
9
Touch [ADJUST].
≥Difference in horizontal direction is characteristic of 
3D video.
≥ If you cannot adjust the attachment position, perform 
the adjustment again after touching [RETURN] and 
checking the subject and the brightness.

VQT4A75_P_eng__lsp.book  17 ページ  ２０１１年１２月１４日　水曜日　午後５時１分 
						

							18VQT4A75(ENG)10
Touch [EXIT] to end the adjustment.
≥When re-attaching the 3D Conversion Lens or 
after an impact etc., it is recommended that you 
perform the adjustment again.11
Start recording. ∫
Adjusting the vertical position of the 
right and left 3D images
When the lens attachment position is out of alignment 
after attaching the 3D Conversion Lens, touch   in 
the Touch Menu and adjust the vertical position 
following the instruction on the screen.
≥  is displayed in the Touch Menu only when the 3D 
Conversion Lens is attached.
VQT4A75_P_eng__lsp.book  18 ページ  ２０１１年１２月１４日　水曜日　午後５時１分 
						

							19
(ENG)VQT4A75
≥Use of a tripod is recommended for recording with a 
stable picture.
≥ You will hear a sound when the video camera is 
moved rapidly with the 3D Conversion Lens attached, 
but this is not a malfunction.
≥ When the adjustment dial is rotated too much, you will 
hear a “clapping” sound and the adjustment screen  will stop moving. In such a case, rotate the 
adjustment dial in the opposite direction until the 
adjustment screen starts moving.
≥ The functions that can be used are limited depending 
on the video camera that is being used. For details, 
refer to the owner’s manuals of the video camera.
To ensure that the 3D video can be safely viewed, pay attention to the following points when recording.
≥ Where possible, record with the video camera in a horizontal state.
≥ Do not get too close to the subject. (record from a distance of at least 1.2 m (3.9  feet).)
≥ When moving the video camera as you record, move it slowly.
≥ Try to hold the video camera as steady as possible when recording while riding in a vehicle or walking.VQT4A75_P_eng__lsp.book  19 ページ  ２０１１年１２月１４日　水曜日　午後５時１分 
						

							20VQT4A75(ENG)∫3D Conversion LensStereo base:  18.3 mm (0.72 q)SpecificationsAttachment screw diameter:
‰49 mm kP 0.75 mm
Lens: When attached to a video camera with a filter diameter of 49 mm;F2.0
f = 1.64 mm (35 mm equivalent; 33 mm)
Minimum recording distance; Approx. 1.2 m (3.9 feet)
When attached to a video camera with a filter diameter of 46 mm;
F2.4
f = 1.47 mm (35 mm equivalent; 34 mm)
Minimum recording distance; Approx. 1.2 m (3.9 feet)VQT4A75_P_eng__lsp.book  20 ページ  ２０１１年１２月１４日　水曜日　午後５時１分