Panasonic Video Multiplexer Wj Fs216 Operating Instructions

-18-
Playback Picture
of CH 1Playback Picture
of CH 2
Playback Picture
of CH 3Playback Picture
of CH 4
Playback Picture
of CH 5Playback Picture
of CH 6
Playback Picture
of CH 7Playback Picture
of CH 8
Example of quad
playback picture sequence
C. Single Spot or Quad Playback Picture
Sequences
1. Repeat procedures A (Single Spot Picture) to moni-
tor a single spot playback picture or procedures B
(Multi Spot Picture) to monitor quad playback pic-
tures.
Note:To monitor quad multi spot pictures, press...

-19-
Note:Two or more pictures on the monitor can be
selected in multi picture mode.
6. Press the camera selection button whose indicator
is blinking.
The selected picture is displayed again for normal
monitoring.
7. To release STILL ON mode, set the MODE SELECT/
CAMERA SELECT switch to MODE SELECT, then
press button 16 (STILL ON).
The STILL ON indicator goes out.
Notes:
• If you press the camera selection button for a cam-
era whose picture is not displayed on the monitor
screen, the operation is...

-20-
MULTISCR Mode
Select this mode to monitor the camera pictures.
Selection of MULTISCR mode permits the following
operations.
Monitoring the camera picture
A. Single Spot Picture
Proceed as described in “Monitoring the Camera
Picture, A. Single Spot Picture” on page 15.
B. Multi Spot Picture
1. Set the MODE SELECT/CAMERA SELECT switch to
CAMERA SELECT.
2. Press the ZOOM/MULTISCREEN/QUAD SHIFT but-
ton. The multiscreen appears on the monitor.
3. Set the MODE SELECT/CAMERA SELECT switch to
MODE SELECT....

-21-
Notes:
• If you press the camera selection button for a
camera whose picture is not displayed on the
monitor screen, the operation is ignored.
• The word “STILL” is not displayed if STILL/
ALARM DISP in MENU 2 OF 3 is set to OFF.
D. Still Multi Spot Picture
The following function is available in multi spot
picture mode only.
1. Set the MODE SELECT/CAMERA SELECT switch to
MODE SELECT.
2. Press the (STILL ON) button 16.  The STILL ON indi-
cator lights.
3. Set the MODE SELECT/CAMERA SELECT to CAM-
ERA...

-22-
nRefer to the operating instructions of each system component for connection and operation.
CAMERA
IN
CAMERA
OUTPLAY IN    MONITOR OUT
ALARM/REMOTE
CAMERA
SW  IN
SIGNAL
GND
16 15 14
1312 11 10 98
654 3
21 7
16 15 1413
12 11 10 9 86
5432
1 7
REC OUT
Cameras Cameras
Camera Drive Unit
VIDEO OUTPUT
VIDEO OUTPUTVideo Monitor
VIDEO INPUT
VIDEO INPUT VIDEO OUTPUT
CAMERA SWITCH
Time Lapse VTRCameras
Note:The WV-80 cannot be used in this system.
CONNECTION 

-23-


Sensor 16       Sensor  1

Buzzer
NO
C NC 

To  Buzzer
Relay
+24V
NC: Normally Closed Contact
NO: Normally Open Contact
C:    Common

• Connection with the Alarm Sensor
You can connect an alarm sensor to record the pic-
tures of channels that receive alarm input signal.
Use an alarm sensor that meets the following con-
ditions:
1. The power capacity must be less than 5 V DC
(open collector output or normally open con-
tact).
2. The voltage between the alarm connector and
the ground terminal...

-24-
nConnection with the Time Lapse VTR
Connect the time lapse VTR as shown in the example below.
246810121416
ALARM
IN 1
COM2ALARM
RESET IN 3
ALARMRECOVER OUT4
ALARM
OUT 5
1 SHOT IN6
7TAPE END
OUT8
WARNING
OUT 9
HUMID OUT10
REC OUT 11REC REVIEW
OUT12
SERIES
REC IN 13
14TIME
ADJUST IN 15
TIME
ADJUST OUT16 COMSERIES
REC OUT
13579111315
PLAY IN
ALARM/REMOTECAMERA
SW  INREC OUT131
14 25
Video Multiplexer
WJ-FS216
VIDEO INVIDEO OUTS-VIDEO
AUDIOCAMERA
SW OUTGND
24 22
147
Time Lapse VTR 

-25-
• Remote Control
You can control the SEQUENCE, MULTISCREEN/QUAD SHIFT, and the camera selection buttons from a remote con-
troller.  These functions are activated by contact with the ground terminal (open collector output or normally open con-
tact).
• Connect the ALARM/REMOTE connector (pin 23) to the ground terminal as shown below.  Switches 1 - 16 select the
cameras (they do not control the alarm input).
Notes:
• Any two or more switches closed at the same time will cause this unit to...

-26-
Power Source: 220 - 240 V AC 50 Hz
Power Consumption: 12 W
Camera Input: 16 (BNC) 2:1 interlaced VBS 1.0V[p-p]/75 W automatic termination/looping through
Playback Input: 1 (BNC) VBS 1.0V[p-p]/75 W
Monitor Output: 1 (BNC) VBS 1.0V[p-p]/75 W
Recording Output: 1 (BNC) VBS 1.0V[p-p]/75 W
Camera Switching Input: 1 RCA pin jack
Alarm Input: 16
Alarm Output: 1 Open-collector 24V DC 100 mA max.
Alarm Recover Input: 1
Operating Temperature:-10°C - +50°C (14°F - 122°F)
Operating Humidity: Less than 90%...

Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan
N0896-1117 YWV8QA4469BN Printed in JapanN30 Gedruckt in Japan
Imprimé au Japon
Impreso en Japón