Panasonic Video Monitor Wv Ld1500 Operating Instructions

							11
CONNECTIONS
Connection Example
DC IN PC IN AUDIOIN OUT IN OUT IN OUT
S-VIDEO VIDEO-B VIDEO-A
AC adapter 
(supplied)Other video monitors
PC
Power cord 
(supplied)
Audio input Video input
S-video
output
Audio output Video output
PC output
 (VGA)
Digital disk recorder 
						

							12
Camera Connection
Connect the video output connector of camera to the
VIDEO IN connector with a coaxial cable. 
Note:Make sure that the cable length between the camera
and monitor is as follows.
Connection with Two or More
Video Monitors
• Connect the VIDEO OUT connector of this monitor to
the video input connector of another monitor with a
coaxial cable.
• Connect the AUDIO OUT connector of this monitor to
the audio input connector of another monitor with an
audio cable.
Notes:
• Up to 10 monitors can be connected to this monitor. If
11 or more monitors are connected, picture quality may
be degraded.
• Total cable length should not exceed 150 m {492 ft.}.
Digital Disk Recorder
Connection
To Perform Recording 
• Connect the VIDEO OUT connector of this monitor to
the video input connector of digital disk recorder (or
other recording devices) with a coaxial cable. 
• If necessary, connect the AUDIO OUT connector of the
monitor to the audio input connector of digital disk
recorder (or other recording devices) with an audio
cable.
To Perform Playback
Do either of the following.
• Connect the VIDEO IN connector of this monitor to the
video output connector of digital disk recorder (or other
recording devices) with a coaxial cable. 
• Connect the S-VIDEO IN connector of this monitor to
the S-video output connector of digital disk recorder (or
other recording devices) with an S-video cable.
To Output Audio Signal
Connect the AUDIO IN connector of this monitor to the
audio output connector of digital disk recorder (or other
recording devices) with an audio cable.
PC Connection
Connect the PC IN connector of this monitor to the analog
RGB output connector of PC (or another device).
Cable type
RG-59/U 3C-2V
RG-6/U 5C-2V
RG-11/U 7C-2V
RG-11/U 10C-2VCable length
250 m {820 ft.}
500 m {1 640 ft.}
600 m {1 968 ft.}
800 m {2 625 ft.} 
						

							13
Before operation, check the connections between monitors
and external devices (cameras, digital disk recorders, etc.)
(Refer to p. 11.)
1. Press the power button. The monitor will be powered
on, and the power indicator will light up in green.
2. Press the INPUT SELECT button.
Every pressing this button can change input signals as
follows.
The signal name will be displayed on the upper right
corner of screen for 3 seconds.Notes: 
• When no input signal is supplied to the monitor, NO
SIGNAL will be displayed on the screen.
NO SIGNAL will continue to be displayed until an input
signal is supplied.
• When the loss of input signal is detected due to cable
disconnection, etc., VIDEO LOSS will be displayed on
the screen.
VIDEO LOSS will continue to be displayed until a
cable is connected.
• When the PC input signal is selected and picture dis-
play position is not proper, perform the VGA output set-
ting for the connected PC.
POWER-ON
Signal name Input signal type
VIDEO A Composite video A 
VIDEO B Composite video B
S-VIDEO S-video
PC PC (Analog RGB)
VIDEO A
VIDEO B/
S-VIDEO PC 
						

							14
AUDIO VOLUME CONTROL
VIDEO ADJUSTMENT AND SETUP
By pressing the + or – button during picture display, you can adjust the audio volume level. While the + or – button is pressed,
the volume level is displayed on the screen.
–:Audio volume level goes down.
+:Audio volume level goes up.
VIDEO ADJUST Menu
Setup of this monitor will be performed in the VIDEO
ADJUST menu.
Notes:
• The menu title display differs depending on the select-
ed input signal. Before adjustment, press the INPUT
SELECT button surely to select the input signal. (Refer
to p. 13.)
• If the power is shut down during setup, the setting val-
ues will not be saved.
1. Press the MENU button. The top menu will be dis-
played.
2. Move the cursor to VIDEO ADJUST by pressing the C
or Dbutton. Then, press the MENU button.• While the VIDEO A, VIDEO B, or S-VIDEO input signal is
currently being selected, the following menu will be dis-
played.
• While the PC input signal is currently being selected,
the following menu will be displayed. Setting item Effect Setting value
AUDIO+:Audio volume level goes up.
–:Audio volume level goes down.0 to + 40
VIDEO ADJUST
SETUP
EXIT
VIDEO ADJUST
BRIGHTNESS
CONTRAST
NORMAL SETTINGS
EXIT
VIDEO ADJUST
BRIGHTNESS
CONTRAST
SHARPNESS
COLOR
TINT
NORMAL SETTINGS
EXIT 
						

							15
3 Move the cursor to the following setting items by pressing the Cor Dbutton. Then, adjust the levels by pressing the + or –
button.
Note:Value can be set differently for each input signal.
4. To reset the settings, move the cursor to NORMAL SETTINGS by pressing the Cor Dbutton. Then, press MENU button.
The setting items of input signal currently selected will be reset to the factory default.
5. To return to the top menu, move the cursor to EXIT by pressing the Cor Dbutton. Then, press the MENU button.
6. After returning to the top menu, move the cursor to EXIT by pressing the Cor Dbutton. Then, press the MENU button. 
The monitor display return to the default status.
Note:If no operation has been performed for 10 seconds or more, the monitor display returns to the default status. Setting item Effect Setting value
BRIGHTNESS
CONTRAST+:Contrast level goes up.
–:Contrast level goes down.– 20 to + 20
SHARPNESS+:Picture quality becomes sharper.
–:Picture quality becomes softer.– 15 to + 15
COLOR+:Color density level goes up.
–:Color density level goes down.– 20 to + 20
TINT (NTSC system only)+:Tint becomes more reddish.
–:Tint becomes more greenish.– 20 to + 20 +:Brightness level goes up.
–:Brightness level goes down.– 20 to + 20
Setting of PC Input
While the PC input signal is being selected, you can adjust
the horizontal position and vertical position.
Note: If the power is shut down during setup, the setting
values will not be saved.
1. Press the MENU button. The top menu will be displayed.
2. Move the cursor to SETUP by pressing the Cor Dbut-
ton. Then, press the MENU button. The SETUP menu
will be displayed.3. Move the cursor to PC by pressing the Cor Dbutton.
Then, press the MENU button.  The PC menu will be
displayed.
VIDEO ADJUST
SETUP
EXIT
PC
H.POSITION
V.POSITION
AUTO
EXIT
SETUP
LANGUAGE
PC
EXIT 
						

							16
Setting item4. Move the cursor to AUTO by pressing the Cor Dbutton. Then, press the MENU button.  The picture display position will
be adjusted automatically.
Manual adjustment
If picture display position is not properly adjusted, move the cursor to the desired setting item by pressing the Cor Dbut-
ton. Then, adjust the levels by pressing the + or – button.
5. To return to the top menu, move the cursor to EXIT by pressing the Cor Dbutton. Then, press the MENU button.
6. After returning to the top menu, move the cursor to EXIT by pressing the Cor Dbutton. Then, press the MENU button. 
The monitor display return to the default status.
Notes: 
• If no operation has been performed for 10 seconds or more, the monitor display returns to the default status.
• Check if the VGA output setting has been performed for the connected PC.
• Depending on the connected PC, the VIDEO ADJUST menu can be controlled from the PC keyboard. However, proper
adjustment is not supported.
When connecting Digital Disk Recorder WJ-HD300 Series
When the PC IN of this monitor is connected to the MONITOR (VGA) of Digital Disk Recorder WJ-HD300 Series, picture display
position may not be properly adjusted even after you perform auto adjustment. In this case, perform Manual adjustment in
Step 4.Effect Setting value
H.POSITION
V.POSITION +: Moves upward.
–: Moves downward.– 20 to + 20 +: Moves rightward.
–: Moves leftward.– 20 to + 20 
						

							Language Setup
You can select the language for monitor display.
Note:If the power is shut down during setup, the setting
values will not be saved.
1. Press the MENU button. The top menu will be dis-
played.
2. Move the cursor to SETUP by pressing the Cor Dbut-
ton. Then, press the MENU button. The SETUP menu
will be displayed.
3. Move the cursor to LANGUAGE by pressing the Cor
Dbutton. Then, press the MENU button. The LAN-
GUAGE menu will be displayed.
4. Move the cursor to the desired language by pressing
the Cor Dbutton. Then, press the MENU button. The
selected language will be applied for monitor display.
17
5. To return to the top menu, move the cursor to EXIT by
pressing the Cor Dbutton. Then, press the MENU
button.
6. After returning to the top menu, move the cursor to EXIT
by pressing the Cor Dbutton. Then, press the MENU
button. 
The monitor display return to the default status.
Note:If no operation has been performed for 10 sec-
onds or more, the monitor display returns to the
default status.
VIDEO ADJUST
SETUP
EXIT
SETUP
LANGUAGE
PC
EXIT 
						

							18
TROUBLESHOOTING
Check the following before requesting repair.
If a trouble cannot be corrected even after checking and trying remedy, contact your dealer.
Check if the power plug is properly connected to the AC outlet.
Power is not turned on.
NO SIGNAL appears on the
screen, and no picture is dis-
played.
OUT OF RANGE appears on
the screen, and no picture is dis-
played.
Picture display position is not
proper while the PC input signal
is being selected.
The power cord insulation is
damaged.
The power cord, plug and con-
nectors get hot during use.
The power cord gets hot when
bent or stretched.
–
Check if the DC plug of AC adapter is properly inserted into the
DC IN jack of this monitor.–
Check if the power cord is properly inserted into the AC adapter.–
Check the cables are properly inserted into the connectors. 11, 13
Check if the cable connection is corresponding with the selected
input signal.11, 13
When the PC input signal does not meet the standards of this
monitor, no picture is displayed. Check the specifications of con-
nected PC.9, 15
Perform auto adjustment on the PC menu. If the picture display
position is not properly adjusted, perform manual adjustment.15
The power cord, plug and connectors are worn out. If you contin-
ue to use it, a fire or an electric shock may occur.
Unplug the AC adapter immediately, and refer servicing to quali-
fied service personnel.
–
Reference 
pages Cause/solutionSymptom 
						

							19
SPECIFICATIONS
Video Monitor
Power Source: 12 V DC, 4.58 A (using the supplied AC adapter)
Power Consumption: WV-LD2000: 51 W (including the supplied AC adapter)
WV-LD1500: 43 W (including the supplied AC adapter)
Display Panel: WV-LD2000: 20 TFT LCD, Built-in dual CCFTs
WV-LD1500: 15 TFT LCD, Built-in dual CCFTs
Display Area: WV-LD2000: 408 mm (H) x 306 mm (V) {16 (H) x 12 (V)}
WV-LD1500: 305.28 mm (H) x 228.96 mm (V) {12 (H) x 9 (V)}
Resolution: 640 x 480 (VGA)
Aspect Ratio: 4 : 3
Brightness: 400 cd/m
2(Typical)
Contrast Ratio: WV-LD2000: 500 : 1 (Typical)*
WV-LD1500: 800 : 1(Typical)*
Display Colors: Approx. 16 000 000
Viewing Angle (L-R/U-D): WV-LD2000: 160°/140°*
WV-LD1500: 176°/176°*
TV Mode: Composite Video Input / Y/C Video Input: NTSC/PAL (Auto)
Horizontal Resolution: 450 or more TV lines
Video Input (VIDEO-A IN, VIDEO-B IN): 1.0 V [P-P]/75 Ω(BNC), composite video signal
Video Output 
(VIDEO-A OUT, VIDEO-B OUT): Auto-termination loop-thru (BNC)
S-video Input (S-VIDEO IN): Y=1.0 V [P-P]/75 Ω, C= 0.3 V [P-P]/75 Ω, Mini DIN jack
PC Input (PC IN): RGB, 0.7 V [P-P]/75 Ω, Horizontal and vertical timing pulse: TTL, 15-pin Mini D-sub
connector
Speaker Output: 1.5 W
Audio Input: –8 dB/Hi-Z, RCA pin jack
Audio Output: Loop-thru output, RCA pin jack
Ambient Operating Temperature: 0 °C to +40 °C {+32 °F to +104 °F}
Ambient Storage Temperature: –20 °C to +65 °C {–14 °F to +149 °F}
Ambient Operating Humidity: Less than 90 %
Screw holes for VESA mounting bracket: 100 mm {3-9/10} pitch, VESA standard
Dimensions: WV-LD2000:
490 mm (W) x 453 mm (H) x 236 mm (D) {19-1/3 (W) x 17-4/5 (H) x 9-3/10 (D)}
(including the monitor stand)
490 mm (W) x 403 mm (H) x 86 mm (D) {19-1/3 (W) x 15-9/10 (H) x 3-2/5 (D)}
(excluding the monitor stand)
WV-LD1500:
370 mm (W) x 375 mm (H) x 236 mm (D) {14-2/5 (W) x 14-4/5 (H) x 9-3/10 (D)}
(including the monitor stand)
370 mm (W) x 325 mm (H) x 86 mm (D) {14-2/5 (W) x 12-4/5 (H) x 3-2/5 (D)}
(excluding the monitor stand)
Weight: WV-LD2000:
8.89 kg{2.0 lbs.} (including the monitor stand)
7.64 kg{16.8 lbs.} (excluding the monitor stand)
WV-LD1500:
5.12 kg{11.3 lbs.} (including the monitor stand)
3.87 kg{8.5 lbs.} (excluding the monitor stand)
* Factory default 
						

							20
AC Adapter
Power Source: 100 V AC to 240 V AC, 50/60 Hz
Output voltage: 12 V DC
Output current capacity: 4.58 A
Dimensions: 120 mm (W) x 60 mm (H) x 35 mm (D) {4-7/10 (W) x 2-2/5 (H) x 1-2/5 (D)} 
(excluding the DC cable)
Weight: 0.35 kg{0.77 lbs.}
Operating Instructions (This Document)  .......................... 1 pc.
AC Adapter (Cable length: 1.8 m {6})  ............................. 1 pc.
Power Cord (1.8 m {6}) .................................................... 1 pc.
Warranty Card ................................................................... 1 pc.
MENU SELECT AUDIO INPUT
SELECTVideo Monitor WV-LD1500MENU SELECT AUDIO INPUT
SELECTVideo Monitor WV-LD2000
370
265
236 86
40
27
325
375
15° 5°
490
265
23686
40
30
403
453
15° 5°
WV-LD1500 WV-LD2000
STANDARD ACCESSORIES
(Unit: mm)