Panasonic Video Monitor Wv Lc1710 Operating Instructions

11
CONNECTIONS
  
Digital Disk 
Recorder
Video 
OutputS-Video 
OutputAudio 
OutputVideo OutputPC
AC Adapter 
(Supplied Accessory)
Power Cord
(Supplied Accessory)
Y    Cb   Cr
Component Output
DV D Video 
InputAudio 
Input
Video Monitor 

12
Connection with the Camera Site
Connect the video output of the camera site equipment to the VIDEO IN connector on the rear of the monitor using coaxial cable.
The maximum coaxial cable lengths available between the camera and monitor are shown below.
Multiple Monitor Connection
To monitor the same video/audio on multiple monitors, connect the VIDEO OUT/AUDIO OUT connector of this monitor to the VIDEO 
IN/AUDIO IN of the other monitor using a coaxial cable and an audio cable. 
Up to 10 monitors in...

13
STARTUP
Onscreen display of NO SIGNAL displays on the center of the 
screen as shown below, when there is no input signal.
Onscreen display of 
VIDEO LOSS displays on the center of the 
screen as shown below, when currently used input is discon-
nected.
Note:
• Press the AU TO button, when screen resolution is 
changed from the connected PC.
  When changing the resolution setting, there are cases 
that auto tuning will not be completed. 
  (Refer to page 19)
Onscreen Display
S-VIDEO VIDEO
COMPONENT...

14
The audio volume can be adjusted with the - or + button when 
picture is displayed.
When these buttons are pressed, the icon and digital display of 
audio volume setting appear on the upper left side of the screen.
-  : Decreases the audio volume.
+ : Increases the audio volume.
AUDIO VOLUME  CONTROL 

15
Settings of this monitor can be done in the Video Adjustment Menu. The display on the screen differs depending on the input signal.
Caution:
•  When onscreen display of NO SIGNAL, OUT OF RANGE, VIDEO LOSS, etc., appears on the center of the screen, the Video 
Adjustment Menu cannot be displayed even if 
MENU button is pressed.
 
Input Signal  Menu Title
VIDEO IN
S-VIDEO IN
COMPONENT IN
PC IN Composite Video
S-Video
Component Video
PC
   NTSC
BRIGHT...

16
   NTSC
BRIGHT                                                       0
CONTRAST                                                            0
SHARPNESS                                                           0
COLOR                                                                   0
TINT                                                                        0
VOLUME                                                                 0
H-POSITION...

17
Note:•  During reset, setting parameters of Video Adjustment 
Menu only are being reset.
NORMAL SETTINGS
   NTSC
BRIGHT -12
CONTRAST 8
SHARPNESS -16
COLOR -6
TINT -2
VOLUME -4
H-POSITION 3
COLOR   TEMP  6500K 
SCAN FULL 
LANGUAGE ENGLISH 
NORMAL   SETTINGS
VIDEO IN
   NTSC
BRIGHT 0
CONTRAST 0
SHARPNESS 0
COLOR 0
TINT 0
VOLUME 0
H-POSITION 0
COLOR   TEMP  STANDARD 
SCAN    FULL 
LANGUAGE ENGLISH 
NORMAL   SETTINGS
VIDEO IN
Caution:•  If power is cut off while setting, it will not store the set-
tings...

18
Setting of PC Input
1. Display the Video Adjustment Menu.
  (Refer to page 15)
  1280x1024@60HzBRIGHT 0
CONTRAST 0
H-POSITION 0
V - POSITION  0
CLOCK 0
PHASE 0
COLOR   TEMP  USER  COLOR
USER COLOR   R   20
USER COLOR   G  20
USER COLOR   B  20
OSD  H-POSITION  0
OSD   V-POSITION  0
VOLUME 0
LANGUAGE  ENGLISH 
NORMAL   SETTINGSPC    IN
2. Set  the BRIGHT, CONTRAST, VOLUME, and LANGUAGE 
parameters. Please refer to page 16 for the operation method.
3. Move the cursor to each setting parameter listed...

19
Notes:
• H-POSITION, V-POSITION, CLOCK and PHASE will 
change depending on the input signal.
  Normally, these parameters need not to be set.
  In case the position of the picture is still shifted even 
AUTO TUNING button is pressed, operate base on the 
procedure below.
  1. Set the left edge of the picture to the left edge of the 
monitor screen while adjusting 
H-POSITION.
  2. Set the right edge of the picture to the right edge of the 
monitor screen while adjusting 
CLOCK.
  3. Repeat steps 2 and...

20
TROUBLESHOOTING
Phenomenon
CauseWhat to do
Power is not turned on.DC input terminal of the AC Adapter is 
not properly connected.
Power supply plug is not properly con-
nected.
The AC cord is not properly connected to 
the AC Adapter.Connect the DC input terminal of the 
AC Adapter to DC IN connector of this 
monitor.
Connect the power supply plug to the 
AC outlet.
Connect the AC cord to the AC Adapter.
NO SIGNAL is displayed on the center 
of the screen and picture is not dis-
played.Cable is not...