Panasonic Ventilating Fan Fv 07vql3 Installation Instructions

Ventilating Fan/Light Combination
FV-07VQL3
FV-08VQL3
FV-11VQL3
INSTALLATION
INSTRUCTIONS
READ  AND  SAVE  THESE  INSTRUCTIONS
Please read instructions carefully before attempting to install, operate or service the
Panasonic Ventilating Fan/Light Combination. Failure to comply with instructions could
result in personal injury and/or property damage. Please retain this booklet for future
reference.
Table of Contents
List of components
Description
Dimensions
Specifications
Unpacking
General safety...

List of components
These Panasonic ceiling mount ventilating fan models use a sirocco fan driven by a capacitor motor.
The motor is designed to have an extended service life with reduced energy consumption.
It also incorporates a thermal-cutoff for safety. The grille can be quickly detached from the main unit. A damper for 
preventing air counterflow is provided. The blower uses a high-capacity sirocco fan developed to reduce the noise
level.
The light unit is an energy-saving, lighting device which uses...

Dimensions continued
3
Specifications
* At 0.0 Static pressure, (Pa)
Unpacking
Unpack and carefully remove unit from carton. Refer to the Supplied components list to verify that all parts are 
present.
General safety information
Do not install this ventilating fan/light combination in ducts where air temperature may exceed 104  F. (40  C)
Make certain that the electric service supply voltage is 120V 60Hz.
Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the...

Protect the power cord from sharp edges, oil, grease, hot surfaces, 
chemicals, or other objects.
Do not kink the power cord.
Do not install the unit where ducts are configured as shown in Fig. A.
Provide suction parts with proper ventilation.
This unit is acceptable for use over a bathtub or shower when installed 
in a GFCI protected branch circuit.
General safety information continued
Fig. A
CAUTION:
1. For general ventilating use only. Do not use to exhaust hazardous 
     or explosive materials and...

5
Remove junction box cover and secure conduit to
junction box knockout hole.(7/8 inch)
Refer to wiring diagram.
Using wire nuts, connect house power wires to ventilating
fan wires:
black to blacks; white to whites; green to greens.
Replace junction box cover.Remove adapter from body and fix to ceiling joists 
using long screws (M4X30). Slide the installation bracket
*into slot next to the junction box. If longer extension 
is needed, assemble brackets*and*as shown below. 
Secure the angular end of the...

6
Installation    (Joist mounting installaton) continuedI
Slide 4 dia. duct onto adapter and secure with tape.
Remove ceiling section.
(Fig.4)
5.
When connecting the light unit and the fan unit to the 
different power sources, connect the conduit to their 
respective junction box shown in Fig. 3 on page 5 and 
connect the wires according to the wiring diagram.
NOTE
Fig. 4
Wiring Diagram
6.
Night Lamp
Fan unit
Red
Black
MotorCapacitor
Black
White
Green
Green Ballast Light unit
Lamp Lamp
Power supply
AC...

7
Installation   (Joist mounting installaton) continuedI
IMPORTANT:
Make sure that body Claws are properly inserted 
into adapter slots.
In case body and blower are installed separately.
Remove 3 screws.
Remove blower section.
Insert fan body into ceiling.
Mount blower section 
and fix with 3 screws.
IMPORTANT:
Make sure that frame is 
properly inserted into
groove of blower section.Secure fan body to adapter using two thumb screws.
8.7.
(Fig.6-1)
(Fig.6-2)
(Fig. 5)
(Fig.6-3)(Fig. 5)
Insert fan body into...

Fluorescent lamp
Light unit
Plastic screws Ceiling
8
Installation   (Joist mounting installaton) continuedI
Insert plug connector I to receptacle I.
(Fig. 8)
9.
Insert the plug connector II , plug connector III into
the receptacle II, receptacle III respectively, and
attach the light unit to the fan unit with 3 plastic screws
(M4X13) and one short screw I (M4x12) . 
Insert the fluorescent lamps and screw the night lamp
into the light unit.
(Fig. 10)
11 .
12.
Insert the lamp cover to the grille and attach...

Ventilating fanAdapter
Long screws
Ceiling
Flange
Fig. 14
Fig. 15
9
Installation      (Wooden header installaton)II
Before installation, secure adapter to fan body using 
two thumb screws.
Install header between ceiling joists using nails or screws.
Secure the Fan/Light assembly to the header with long 
screws (M4X30).
Slide the 4 circular duct onto the adapter and secure 
with tape. Remove the junction box cover and secure 
conduit to junction box knockout hole. (7/8 inch)
Refer to wiring diagram.
Using...

Thumb screws
10
Installation 
   (Between joist mounting installation)
1. Before installation, secure adapter to fan body by using
    two thumb screws.
2. Insert the installation bracket III into slot of the adapter 
    side.
III
(Fig. 16)
(Fig. 17)
Fig. 18installation bracket I
installation bracket IV
Frame
Fig. 16
3. Insert the installation brackets I and IV into slot.
(Fig. 18)
Fig. 17
Fan body
installation bracket III
Fan body
adapter