Panasonic Ventilating Fan Fv 05vfl1 Installation Instructions

							11
Fan body
Fig. 25Clamp plate
2-square knock-outHanddriver
Replace with clamp plates(accessories) andsecure the fan
body on ceiling board with 2 short screws III (M4 x 6) from
inside of the rame. (Fig.25)
Insert fan body into ceiling as shown in Fig.24.
Fig. 23
Fig. 24
Insert the blower into the fan body. (Fig. 26)
Tape
Tape
Short screwsIII
Fan body
Fig. 26
INSTALLATION (IN EXISTING CONSTRUCTION) CONTINUEDIII
Remove the 2 square knock-out carefully from surface
of the frame by screw driver ( Fig.23) and remove the
bracket cover on the other side of the frame body.
Secure the fan body to the adaptor by using one thumb screw
as shown in Fig.5-3 of page 6.
Fan body
Ceiling
Adapter slots
Claws
Ceiling
BlowerCeiling 
						

							12
13
Mounting spring Slot
Maintenance (Replacement of fluorescent lamp of night lamp)I
Screw
Connect plug cnnector to receptacle . (Fig.8 of page 6.)II
Secure blower to fan body with screws that were loosen before.
(Fig.27)
Fix the light kit set plate to the frame using 4 short screws
(M4x6)III
as shown in Fig.11 of page 7.15
Insert the fluorescent lamps andscrew the night lamp into
the light unit as shown in Fig.12 of page 7.17
Insert the lamp cover to the grille andattach the grille to the
fan unit as shown in Fig.13 of page 8.18
16Insert the plug connector andplug connector into the receptacle
andreceptacle respectively, andattach the light unit to the fan
unit with 2 short screws (M4x16) and1 short screw (M4x8) as
shown in Fig.12 of page 7.II III
II III
III
Mount the fan body with thumb screw (on the right side of
bottom of the adaptor) as shown in Fig.7 of page 6.
Fan bodyFig. 27
Fig. 29(Fig. 29)
(Fig. 30)
Fig. 30 (Fig. 28)
Fig. 28
INSTALLATION (IN EXISTING CONSTRUCTION) CONTINUEDIII
Screw driverCeiling
WARNING:
1. Disconnect power source before working on unit.
2. The lamp's glass is fragile. Please handle with
care. To remove lamp, grasp at base andmove
back andforwardto loosen.
Do not pull hardon the lamp or you may break the
glass.
3. 4W night lamp has threaded base. Remove by
turning counterclockwise.
1. Remove grille.(Squeeze mounting spring andpull down)
Grille Gloves
2. Disconnect the connector II or connector of light
unit.III
3. Change the fluorescent bulbs (Panasonic FDS 13E
27. U/ 2, 13W or FQ13E 41.U/ 2, 13W or FQ13E 35.U / 2,
13W) or the 4W incandescentlamp, connect the connector
or connector andreplace the grille. II III
12
14 
						

							13
Maintenance (Cleaning)II
Vacuum cleaner
Mounting spring
Slot
(Fig. 32)
Fig. 31
(Fig. 33)
Fig. 33
Fig. 32
Fig. 34
(Fig. 31)
(Fig. 12 on page 7 and Fig.13 on page 8)
WARNING:
Disconnect power source before working on unit. Routine maintenance must be done every year.
CAUTION:
1. Never use gasoline, benzene, thinner or any other similar chemicals for cleaning the grille andthe
ventilating fan.
2. Do not allow water to enter motor.
3. Do not expose plastic parts to temperature over 140 F (60 C).
oo
1. Remove grille.(Squeeze mounting spring andpull down)2. Wash andclean grille. (Use non-abrasive kitchen
detergent)
Grille Gloves
3. Remove dust and dirt from fan body using a vacuum
cleaner. (Remove bulbs if necessary.)
4. Using a cloth dampened with kitchen detergent,
remove any dirt from fan body. Wipe dry with new
cloth.
5. Replace bulbs andgrille. 
						

							PRODUCT SERVICE
PANASONIC CANADA INC.
One Panasonic Way, Secaucus, NJ, 07094
PANASONIC CONSUMER ELECTRONICS COMPANY
www.panasonic.ca
14
5770 Ambler Drive, Mississauga, ON L4W 2T3
The unit shouldbe servicedby qualifiedtechnicians only.No service information is providedfor customers. Your product
is designedandmanufacturedto ensure a minimum of maintenance. However, shouldyour unit ever require service, a
nationwide system of factory service centers and AUTHORIZED INDEPENDENT SERVICE CENTER is maintained to
support your product's warranty.
(In the U.S.A., call 1-886-292 7292 to locate the Panasonic AuthorizedService Center nearest you.)