Panasonic Va-824 Key Telephone System Installation And Programming Manual

CO line or PBX line 
MODE 2 
If the system is connected behind a PBX, this programming is required. 
This programming is for auto pause and toll restriction setting. 
Key Operation LCD indication Remarks 
Program 
mode 
Program 
step 
CO line 
(Initial) 
. , , . ,. , . . . . , ., . . . . or . . . . . . . . . . . . . . . . . . . . . . 
Desired 
program 
mode I coiol? 
01 
Either 0 or 1 depending on the 
These program steps are made for each telephone line(COL). 
1 COL 1 Program step 1 LCD indication 
I 
3...

Automatic outside line selection group 
You can have an outside line which is connected automatically from SLT. 
This outside line being not used can be selected automatically by pressing dial key 9. 
This will be set whether the outside line is automatically selected or not. 
This feature can be also used by the key telephone. 
NOTE: When you use this feature, set program and cut the jumper line at the inside of KSU(See page 14). 
MODE 2 
Key Operation 
LCD indication 
Remarks 
Program 
mode 
Program...

Length of DTMF signals 
If mis-dialing is sometimes made while tone dialing, change the tone duration time to 240 m sec. 
When you have MCI or Sprint lines, and if you wish to use BANK account balance service, set to 240 m sec. 
MODE 2 
Program 
mode 
Key Operation 
. 
OHrff 
&a 
m l!rm m 
LCD indication Remarks 
80 msec 
(Initial) 
240 msec 
Desired 
program 
mode 
-Either 0 or 1 depending on the 
desired program mode. 
These program steps are made for each telephone line(COL). 
COL Program step LCD...

Minimum pause MODE 2 
You can change the minimum pause for the tone dialing signal. If you cannot dial at initial set (80 m set), specify 
The minimum pause is the pause time between tone dialing signal and another tone dialing signal. 160 m sec. 
Program 
mode 
Key Operation 
LCD indication 
Remarks 
Program 
step 
Desired 
program 
mode 
Storing 
command 
c 
80 msec 
(Initial) RI 0 
, , , . . . . ., . . . . . .,,, or . . . ..I............,,,, 
160 msec 
, 
I elms 
01 
61 
-Either 0 or 1 depending on...

Ring detection time 
MODE 2 
If you have a problem of incoming ring signal like that the first ring is normal but second does not ring, you need to set it to 
8 seconds as your incoming ring cycle is more than 6 seconds. 
Key Operation LCD indication Remarks 
Program 
mode 
6 set 
(Initial) 
Desired 
program 
mode 
co107 0 ; 
Either 0 or 1 depending on the 
desired program mode. 
Storing 
command 
I 
These program steps are made for each telephone line(COL). 
COL Program step LCD indication 
COL Program...

( Key telephone setting 
Telephone type MODE 3 
You can also connect a AT & T 2500 type(DTMF) single line telephone to the system in addition to the key telephone. The setting 
specifies whether it is a key telephone or single line telephone for extensions 30 to33. 
When you use single line telephones, the optional SLT card is necessary to KSU. 
Key Operation LCD indication Remarks 
Program 
mode 
Program step 
Desired 
program 
mode 
Key telephone 
(Initial) 
. . . . . . . . . . . . . . . . . . or...

Line key assign 
MODE 5 
You can set any of the line numbers from 01 to 03 on Line/FF key with two digits, 
Program 
mode 
LCD indication 
Remarks 
Extension No. 
Line key . 
CO line No. 
Desired 
program 
mode 1 clUU/Ul 1 
tt 
L I i Either 01, 02, 03,04,05,06,07or 
; 08 depending onthe desired 
; program mode.  I I 
COL No. 
Storing 
command 
I 
End [-fEJ--- 
1 
]+[-E-] 
64  

MODE 5 
For EXT. No. IO For EXT. No. 14 
Line key No. Program step LCD indication 
1 
x1001 c/231 0: 
Line key No. 
Program step LCD indication 
1 
x1401 c:llz: 01 
2 ~1002 c IZC?? 02 
3 x1003 c 1333 
33 
4 ~1004 c /uuY 2Y 
5 x1005 c luu5 us 
6 Xl006 c :u3s ES 2 Xl402 c:w2 u2 
3 x1403 
c:clu”3 33 
4 
x1404 c IYOV GY 
5 
x1405 c :vos 05 
6 Xl406 c IVuS us 
7 x1007 c:u2: u: 
8 Xl008 
c :u”u”8 08 
7 
x1407 clYu7 u: 
8 Xl408 
c :YO8 D8 
For EXT. No. 11 
Line key No. 1 Program step LCD indication 
7 x1107 -...

MODE 5 
For EXT. No. 18 For EXT. No. 22 
For EXT. No. 19 For EXT. No. 23 
For EXT. No. 20 
For EXT. No. 24 
66 :  

MODE 5 
For EXT. No. 26 
Line key No. 1 Program step LCD indication For EXT. No. 30 
Line key No. 
Program step LCD indication 
1 X 2601 cl?Sul 0: 
2 X 2 6 0 2 c2S22 CL 
3 X 2 60 3 
ci26u”3 u”3 
4 X 26 04 c!?SSY uY 
5 X 26 0 5 cl?s35 us 1 x 3001 
c3il3: 0: 
2 x 3 
0 0 2 
c3202 02 
3 x 3 03 
0 
c3ou”3 03 
4 x 3 
004 c3u”3Y 2s 
5 x 3 0 5 
0 
c3ou”s 3s 
For EXT. No. 27 
Line key No. 1 Program step LCD indication 
6 X 3 0 06 c3D26 36 
7 x 3 00 7 c3v”u”: 0: 
8 x 
3 0 0 8 ~3008 u”8 
For EXT. No. 31 
Line key...