Panasonic Va-1232 Key Telephone System Installation And Programming Manual

You can answer incoming calls without pressing Line key. There are two systems for answering: one is to 
simply 
lift the handset 
and the other is either to lift the handset or press ON/OFF key, 
Program 
m0de 
Program 
step 
Desired 
program 
mode 
........... 
.................. ........... 
-Either 0, 1 or 2 depending on the 
desired program mode.  

You can specify telephones to ring in case of night time incoming calls in systems programmed for this purpose . This is 
necessary when the places for r ceiving incoming calls are different at daytime and night time. 
Program 
step 
Desired 
program 
mode 
Only night time ring 
set TEL will ring.’ 
(Initial) 
COL ring set TEL 
will ring,too. 
Either 0 or 1 depending on the 
: desired rxoaram mode.  

Hold recall can 
aming tone sounds once ace&in period has elapsed after a calI has been put on hold. 
disabled, or set for immediately, 30 seconds, 1 minute or 2 minutes. 
Program 
Desired 
program 
mode 
Either 0, 1, 2, 3 or 4 depending 
Storing 
on the desired program mode. 
command  

Up to two door boxes can be used with this system by corm ng the door box card to KSU. You can set it so that the signal 
from the door box is heard or not heard through a telephone ich has been programmed in advance. 
You do not have to change the programming-if door box is not connected. - 
Program 
e 
Program 
step 
Desired 
program 
mode 
an n nn 
,.*.. * . . . . . ..I.. *. or . . . ..**.**.**t......*. 
(hitial) 
Either 0 or 1 depending on the 
desired program mode.  

Two lypss of sensor can bs used by connecling the door box card to KSU. An alarm will sound from a telephone which has been 
programmed in advance. The operating method for these sensors is specified either as close detection or open detection. 
Program 
mode 
Program 
step 
Desired 
program 
mode 
(Initial) 
eteci - open 
Storing 
command 
-Either 0 or 1 depending on the 
desired program mod&.  

in eth 
You can specify the method for stopping the sensor alarm. This specification can be that either no alarm sound is given from 
the sensor or that the alarm sound is stopped by lifting the handset of alarmed telephone. 
Program 
ode 
Program 
step 
y SenSOr 
(Initial) 
. . . . . . . . . . . . . , . . . . or . . . . . . ..*.....*.*.*... 
Desired 
program 
mode y handset 
(Off-hooking) 
1 Either 0 or 1 depending on the 
: desired program mode.  

hen you want to hold an outside line with SLT, press hook switch breifly. 
If the hooking time is longer than the time which programed,the phone line will be disconnected. If you do not use frequently 
hold function, this hooking time should be set to less than 
0.5 second. 
Progra 
MO&? 
Program 
step 
Desired 
program 
mode 
(Initial) 
Storing 
command Either 
0 or 1 depending on the 
: desired program mode.  

recall f 
You can set a telephone so that a warning tone sounds once a certain period has elapsed after a call has been put on hold. 
Hold recall can be disabled, or set for immediately, 30 seconds, 1 minute or 2 minutes. 
Program 
mode 
Program 
step 
Desired 
program 
mode 
: the desired program mode 
5 .  

This feature is for setting the correct time for a key telephone with an LCD display. 
mode 
Program 
step 
Desired 
pro”gram 
mode A : 12:o 
P : 12:o is for night. 
is for daytime.  

This feature is to program to output data onto the S 
This is necessary when you want to notify the call record. 
You can set for not outputting SMDR data, outputting the data with the title or outputting the data only. 
Program 
mode 
Program 
step 
Desired 
program 
mode 
L. n 
................. 
................. or ...... ....... 
Outputting da’r& 
ith title 
Either 0, 1 or 2 depending on the 
desired program mode