Panasonic Va-1232 Key Telephone System Installation And Programming Manual

All programming changes are made at 
Extension No. 10 and it is recommend- 
ed to use key telephone with a LCD 
display (VA-1 2022 or VA-12022-B). 
@ Press the ON/OFF button. The ON/ 
OFF indicator and MIC indicator 
lights up and a continuous tone is 
emitted. 
mode 1: 
System setting 
mode 2: COL setting 
mode 3: 
Key telephone setting 
mode 4: Incoming call ringing setting 
mode 5: Line/FF key setting 
mode 6: Restriction setting 
mode 7: 
Display time setting 
@ Press the program step numbers for...

. 
(Set up for program mode) 
Programming for each mode 
gram I  

You can have access to an outside line through PBX. This feature is necessary when the system is connected to PBX. Set 
by sp@ccifying one digit from among dialing numbers 0 to 9 (PBX line access number ), 
in at i 
Program 
mode 
Program 
step 
Desired 
program 
mode 
0 thru 9 can be programmed. 
Initial setting is 9. 
30  

You can place a pause automatically after the first digit dialing number when having access to outside numbers through PBX. 
Set by specifying one digit from among dialing numbers 0 to 9 (PM line access number ). 
Program 
e 
Program 
step 
Desired 
program 
mode 
-0 thru 9 can be programmed. 
(possible multiple digit) 
End  

hen making an outside call by a key telephone with an LCD display, you can set how many seconds after completion of 
dialing you want the conversation time to appear on the display. 
Program 
mode 
Program 
step 
(Initial) 
Desired 
program 
mode 
fter 30 set 
-Either 0 or 1 depending on the 
desired program mode. 
Storing 
command  

You can set the length of open time for an outside line with FLASW key and that of auto-flash time with REDIAL key function. 
hen you wish to use the call aiting service, just press FL 
If the system is connected to the P X line and you do not use the hold function of PBX system, set to 2 seconds. 
Program 
mode 
Program 
step 
.6 set 
1 set (Initial) 
2 set 
Desired 
program 
mode 
-Either 0, 1 or 2 depending on 
the desired program mode.  

By pressing REDlAL key, a pause can be stored in the system speed memory and one-touch key. One pause is counted as one 
digit. This is used when YOU need to wait for a second dial tone when dialing an outside line. 
Program 
e 
Program 
step 
2 set 
(Initial) 
Desired 
program 
mode 
3 set 
L 
Either 0 or 1 depending on the 
: desired program mode. L  

sle 
You can divide the system speed dial memory into two groups. The range of address numbers for group A is from 00 to XX. 
XX is the last address number of the range and the designation should be between 
00 to 89. 
Program 
mode 
Program 
step 
Desired 
program 
mode 
i Program the last number of the 
: range. 
0 thru 9 can be programmed. 
Initial setting is 89.  

YOU can divide the system speed dial memory into two groups. The range of address numbers for group B is from YY to 89. YY is 
the first address number of the range and the designation should be between 
00 and 89. 
Program 
erali 
in 
at i 
Program 
step 
Desired 
program 
mode 
Program the first number of the  Program the first number of the 
range.  range. 
0 thru 9 can be programmed.  0 thru 9 can be programmed. 
Initial setting is 00.  Initial setting is 00. 
End  

hen making an outside call, you can set SO that a short alarm tone sounds from the speaker or handset every three minutes. 
Program 
e 
I,... in 
Program 
step 
lawn tone 
(Initial) 
. . . . . . . . . . . . . . . . . . or 
we alarm lone 
Desired 
program 
mode 
I 
Either 0 or 1 depending on the 
: desired program mode. 
Storing 
command