Panasonic Tv Dvd Vcr Combination Pv Df2003 Operating Instructions

							31
Timer Operation
Repeat steps 1 and 2 on page 30.
1
Press PROG twice to exit this mode.
2
3
To Clear program...
4
Press  to select 
the desired program.
  
1) Press SET to 
display.
2) Press 
 to 
select and press 
SET or 
 
  
 to set 
new program 
contents.
3) Press PROG.
Cancel a Timer Recording: 
(Recording is in progress)
 
Hold down STOP for a few 
seconds to cancel the Timer 
Recording.
 Any future daily or weekly recordings will 
be performed as programmed.
Press ADD/DLT.
Review, Replace or Clear 
Program Contents : (
Recording 
is not in progress)
  2 minutes before Timer recording is performed, “PLEASE 
PREPARE FOR TIMER REC” appears and/or the PROG 
TIMER Indicator  ashes. Be sure a cassette with record 
tab is loaded and the unit is in Stop mode.
  If the start times of two programs overlap, the lower 
numbered program will have priority.
  If the start time for a Timer Recording comes up during a 
normal recording or One Touch Recording (page 18), the 
Timer Recording will not be performed.
  If there is a power interruption of more than one minute, 
the recording may not be performed or continued.
  If “INCOMPLETE” appears after all items have been set, 
check all entries and make necessary corrections.  
*Important: If a remote control button does not work when pressed, press the  button on the 
remote and try the button again.
CANCEL : ADD / DLT  SELECT   1 - 8 :          ENTER   : SETEND       : PROG     
8  SAT  9:00P  12: 00A 08DATE       START       STOP       CH
SELECT :        SET       : SET END       : PROG   BACK :  
SELE CT  START  DATE
TODAY
SLP
- - - - - - - - -- - - - - - - -- - - - - - - 
P  DT  START    STOP    CH  SPD1  -- -- : --   -- : --  --  --2     8  10 : 00p 12 : 00a 125    SP3   10    8 : 00p  9 : 00p  10    SP4   SU    9 : 00p 10 : 00p     L    LP
SELECT
   1 - 8 :          ENTER   : SET     END       : PROG    
To Replace program...
SURROUND
PROG SELECT
     SET ADD/DLT
STOP
Notes 
						

							32For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Universal Remote Control is...The Remote Control may be set up to control some basic 
DSS or Cable box functions.
The Universal Remote Control Setup
1
Press   , FM, DVD or DSS CABLE on the remote 
control to select the desired mode. (See below for buttons 
available in each mode.)  Once the remote control has been properly set up, you can 
select TV-VCR, FM, DVD, DSS or CABLE mode depending 
on which functions you wish to control.
Find your DSS box or Cable box Brand Code 
Number from one of the charts on the next 
page.
3
Con rm code entry. Press POWER* to turn 
selected unit ON or OFF.
  See below for controllable functions in each mode.
  Please repeat the Universal Remote Control Setup after 
replacing remote control batteries.
  The remote control will not operate all DSS receivers or Cable 
Boxes made by the manufacturers listed. If you get no results, 
your particular brand cannot be controlled.
2
Set up remote. Hold down DSS CABLE and 
press NUMBER keys to enter code.
  If code number is 100 or greater, e.g., press 1 - 0 - 2 for 
102.
Using the Universal Remote Control 
(Available Buttons / Functions)
Set to , FM, DVD:
  Cable Box Universal Remote Control Feature
Set to DSS CABLE:
  Basic VCR functions, e.g. PLAY, REC, etc.
  CABLE/DSS function, e.g. POWER, ENTER, NUMBER keys 
(except 100 key), CH UP/DOWN.
All TV functions, as well as functions of TV-VCR, FM, or 
DVD.
SURROUND
ENTER
POWER
TV-VCR
DVD
DSS CABLE
FM
NUMBER
keysNotes 
						

							33
Advanced Operation
  In DSS or CABLE mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection.
  In DSS or CABLE mode, POWER, CH Up/Down, NUMBER Keys, ACTION, PROG, DISPLAY/ENTER, 
SEARCH/SKIP- 
|, R-TUNE, SELECT, SET, CM SKIP/ZERO/SKIP+ |, COUNTER RESET/ZOOM, ANGLE, 
AUDIO, TITLE, SUB TITLE, MENU, or ADD/DLT are not available. Press   , FM, DVD to use these functions.
  Depending on your DSS receiver or Cable box brand, some of the functions listed may not be remote controllable.
  Some DSS receiver or Cable box brands require you to turn on the power manually.
  Due to changes in infra-red commands used by manufacturers, some brands have several codes. If your unit does 
not respond to the  rst code, please try the next one.
*Important:  If a remote control button does not work when pressed, press the  
, DVD, FM 
button on the remote and try the button again.
  DSS Brand Code Numbers
Toshiba .................................................................90
Hitachi/ Hughes ..............................................91, 99
Primestar..............................................................92
Drake....................................................................93
Magnavox .......................................................94, 95
Uniden ............................................................94, 95Optimus ..........................................................94, 95
Panasonic ............................................................96
ProScan ...............................................................97
RCA......................................................................97
SONY ...........................................................98, 105
  Cable Box Brand Code Numbers
Archer.............................44, 06, 01, 120, 05, 63, 126
Cableview...........29, 09, 01, 63, 120, 44, 42, 30, 52, 
04, 124, 126
Citizen ....................44, 52, 30, 63, 42, 04, 124, 126
Curtis......................................08, 09, 25, 61, 53, 87
Century ......................................44, 51, 75, 59, 126
Cabletenna ...................29, 09, 01, 63, 120, 44, 126
Cable Cinema..................29, 09, 01, 63, 120, 44, 126
Diamond.........................29, 09, 01, 63, 120, 44, 126
Eagle .........................62, 40, 22, 13, 58, 20, 26, 107
Eastern...................................................28, 29, 130
Explorer...................................08, 09, 25, 61, 53, 87
Gemini....................................................30, 04, 124
General Electric.......................................01, 57, 120 
General Instruments............01, 84, 83, 34, 03, 02, 04, 
55, 65, 66, 67, 68, 120, 106, 
121, 122, 115, 117, 118, 124
Gerrard................................................44, 51, 75, 59
GC Electronics ................44, 42, 63, 29, 30, 52, 04, 
124, 126
Hamlin ................41, 14, 15, 28, 102, 104, 103, 130
Hitachi ..................................................................31
Jerrold ...............01, 84, 83, 34, 03, 02, 04, 55, 65, 66, 
67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Jasco......................................................30, 04, 124
Macom..................................................................31
Magnavox.....................................................26, 112
Matsushita...................................17, 16, 08, 87, 109
Movietime........................32, 39, 42, 44, 126, 38, 40
Maestro...........................................................74, 35
NEC.....................................................40, 19, 38, 32
NSC.....................................................40, 19, 38, 32
Novavision...............................08, 09, 25, 61, 53, 87
Next Level....................01, 84, 83, 34, 03, 02, 04, 55, 
65, 66, 67, 68, 120, 106, 121, 122
Oak.................................................46, 11, 129, 101Oak Sigma .....................................46, 11, 129, 101
Panasonic ..................................17, 16, 08, 87, 109
Philips.....................23, 24, 20, 13, 07, 50, 128, 129
Pioneer .....................................................06, 05, 12
Pulsar .....................04, 42, 63, 44, 30, 52, 124, 126
Quest........................................................06, 05, 12
Radio Shack ...............................44, 51, 75, 59, 126
RCA............................................17, 16, 08, 87, 109
Realistic......................................44, 51, 75, 59, 126
Recoton ......................................44, 51, 75, 59, 126
Regal ..................41, 14, 15, 28, 102, 104, 103, 130
Regency .................................................28, 29, 130
Rembrandt .......44, 42, 63, 29, 01, 32, 39, 120, 126
Samsung ......................................42, 06, 32, 05, 40 
Scienti c Atlanta.....................08, 09, 25, 61, 53, 87
Sheritech ..............................................................27
Signal ...........................................................26, 112
SL Marx................42, 06, 32, 40, 43, 44, 52, 63, 126
Sprucer........................................17, 16, 08, 87, 109
Standard Components.................32, 39, 42, 44, 126
Stargate.................04, 42, 32, 40, 63, 44, 30, 52, 06, 
124, 126
Sylvania..........................................................19, 18
Teknika ...........................................................74, 35
Telecaption ...................................................77, 127
Teleview..................................40, 19, 38, 32, 42, 06
Texscan ..........................................................19, 18
Tocom...................................34, 33, 01, 42, 66, 120
Toshiba .................................................................36
Unika ............................44, 42, 63, 29, 01, 126, 120
Universal ..............................52, 43, 44, 63, 42, 126
Viewstar ...................62, 40, 22, 13, 58, 20, 26, 107
Videoway ..........................................07, 23, 50, 129
Vidtek ...................................................................64
Zenith ...............................................07, 23, 50, 129
Notes 
						

							34For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Search System is ...Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are 
made, program index and information are also included. These index marks can be used to access or 
scan recordings.
1
Press SEARCH* 
in Playback or 
Stop mode to 
display INDEX 
SEARCH screen, 
and then press 
NUMBER keys to 
select the 
recording number.
 To calculate 
number, see below.
Index Search
Go directly to the desired recording.
  If Index Search is started very close to an index 
mark, that index mark may not be counted in 
the search.
2
Playback begins 
at search end. To 
search forward 
or back 1 index, 
press FF or REW 
while screen left 
is displayed (10 
seconds).
NOTE:    indicates start points of each recording.
6157234
■ To calculate the Index NumberExample 1:To go to rec. 2 from rec. 4, enter 3 and press 
REW.
17534 62
Example 2:To go to rec. 6 from rec. 2, enter 4 and press FF.
 ENTER I NDEX NUMBER : 1 US I NG 1- 9 KEYS
FOR
WARD SEARCH : FF
REVERSE  SEARCH : REW
EX
 I T    :   SEARCH   
I NDEX SEARCH
 
FOR
WARD SEARCH : FF
REVERSE  SEARCH : REW
I NDEX SEARCH
To cancel, press PLAY.
Tape Operation
Press FF or REW to start search.FF REW
SURROUND
SELECT     SET NUMBER
keys
REW
FF
SEARCH
Note 
						

							35
Advanced Operation
*Important: If a remote control button does not work when pressed, press the  button on the 
remote and try the button again.
Repeat Play
Set to see a recording over and over.
PLAY REPEAT  ON
To turn “ON,”press PLAY/REPEAT on the unit  repeatedly 
in Playback mode to select “REPEAT ON.”
To turn “OFF,”repeat above to select “REPEAT OFF.”
  Playback repeats when tape end is reached or 
an unrecorded portion longer than 30 seconds is 
detected.
  For repeat play in DVD mode, see page 55.
PLAY/REPEAT
Note 
						

							36For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Press  COUNTER 
RESET at the 
desired position to 
reset to “0:00:00.”
Tape Operation (continued)
Zero Search
To quickly return to a speci c tape counter 
location. 
1
2
Press STOP.
4
5 3
Continue playback, rewind, or fast 
forward.
Press DISPLAY* during playback to 
display the Counter.
Press  CM/ZERO in stop mode to start 
ZERO SEARCH.
0 : 00 : 00SLP
PLAY  12 : 00   PM
  Unit goes into FF or REW mode and stops at the 
last point the Counter was set to 0:00:00.
SURROUND
DISPLAY
STOP
COUNTER
RESET
CM/ZERO 
						

							37
Advanced Operation
Press  CM/ZERO repeatedly to select skip time in 
Playback mode.
  Commercial Skip
By pressing the CM/ZERO button in Playback mode you 
can skip over 1 to 3 minutes of recorded tape in just a few 
seconds.
  No indication appears.
■  Auto Shut Off 
No broadcast signal in TV mode (Only when Weak Signal 
Display is set to OFF.), DVD stops, or blank tape is played 
for 5 minutes. 
➞ Power turns off   This feature is canceled if any button is pressed during above 
conditions.
■ Auto Playback
Insert a tape in Power off mode ➞ Power turns on    Playback begins if tape has no record tab.
■ Auto Rewind (except for Recording)
Tape reaches its end ➞ Rewind, ➞ Stop 
■ Playback Auto Eject (Repeat Play is “OFF”)
Tape with no record tab reaches its end ➞ Rewind, ➞ Stop, ➞ Eject
 
Auto Operation Functions
*Important: If a remote control button does not work when pressed, press the  button on the 
remote and try the button again.
OFF
1st  Press       1 min skip
2nd  Press       2 min skip
3rd  Press       3 min skip 
						

							38For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
When “ON” is selected, the picture is displayed 
even when a broadcast signal is weak or 
non-existent.
Weak Signal Display Feature
1
2
3
  “ON”  =  Picture is displayed regardless of signal 
condition, and may not always be clearly 
visible.
  “OFF” =  Screen turns solid blue when signal is absent 
or weak.
  If unit is connected to equipment which has blue back 
feature, selecting “ON” will have no effect on the other 
equipment.
4
Press ACTION* to display MAIN MENU.
1) Press   to 
select “CH.”
2) Press SET to 
display SET 
UP CHANNEL 
screen.
Press ACTION twice to return to the 
normal screen.
1) Press  to 
select WEAK 
SIGNAL 
DISPLAY.
2) Press SET to 
set “ON” or 
“OFF.”
M A I N  MENU
DVDLOCK
CH
CLOCKTV
LANGUAGE
END         : ACT I ON SELECT  :                            SET : SET 
531
ANTENNA  :   CABLE
AUTO   SETWEAK  S I GNAL   D I SPLAY : OFF
SELECT :          SET       : SETEND       : ACT I ON  
           SET  UP  CHANNEL 
Special VCR Features
SURROUND
SELECT     SET ADD/DLT
ACTIONNotes
 It is necessary to enter TV 
mode by pressing 
 before 
selecting “CH” on the MAIN 
MENU.
 Check List 
						

							39
Advanced Operation
VCR Lock
All operations are prohibited except Timer 
recording and tape eject. Useful for families with 
small children.
In Stop mode, hold 
down REC on 
the unit without a 
cassette inserted for 7 
seconds to turn “ON.” 
(Please ignore “NO 
CASSETTE” warning.)
Repeat above with or 
without cassette to turn 
“OFF.”
  VCR Lock is canceled automatically after about 24 
hours if clock is set.
*Important: If a remote control button does not work when pressed, press the  button on the 
remote and try the button again.
VCR  LOCK  ACT I VATED
VCR  LOCK  OFF 
REC
Remote Warning Feature
1
Press ACTION twice to return to the 
normal screen. 
When Universal Remote Control (page 32) is used, 
and this feature is set to “ON,” a warning appears 
whenever an invalid key is pressed in DSS or 
Cable mode.
2
43
Press ACTION to display MAIN MENU.
1) Press    
  to 
select “TV.”
2) Press SET to 
display SETUP 
TV screen.
1) Press     to 
select 
REMOTE 
WARNING.
2) Press SET to 
set “ON” or 
“OFF.”
 “REMOTE WARNING : OFF”
➞  Remote warning will not appear even if 
invalid key is pressed.
SELECT :          
END       : ACT I ON      
              SET  UP  TV   
SET : SET
CAPT I ON  
 I NPUT  SELECT       : TUNER SET  UP  V I DEO / AUD I ODVD  VOL  ADJUST   : + 2FM  ANTENNA            :  I NTREMOTE  WARNING     : ON
M A I N  MENU
DVDLOCK
CH
CLOCKTV
LANGUAGE
END         : ACT I ON SELECT  :                            SET : SET 
531 
						

							40For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Press ACTION* to display MAIN MENU.
Enter Secret Code
A 4-digit code must be entered to view a blocked 
program or change rating settings.
1
  Some rental movies do not include V-Chip 
data.
  DO NOT forget your secret code.
  Once ratings are set, restricted tapes or 
programs cannot be accessed unless the 
secret code is entered.Changing your secret code
 You will need your current code.
Do steps 1 ~ 3. In step 4, press CLEAR to clear 
current code.
Repeat steps 3 and 4 to enter new code.
Process of V-Chip Control Feature
SetupBlockingEnter Code
Press SET to display 
US Ratings menu 
(see pages 41-42).
Or
Press ACTION twice 
to exit.
4
1) Press NUMBER 
keys to enter your 
secret code.
2) Enter same 
code again for 
con rmation.
3
  Step 2) not necessary when changing rating or 
secret code.
  Take care that you are not observed entering the 
secret code.
To Make Corrections
Press  
 repeatedly to move the cursor.
Press NUMBER keys to make the correction.
1) Press    
  
 to 
select “LOCK.”
2) Press SET to 
display LOCK 
screen.
2
V-Chip Control Feature is...This unit has a built-in V-Chip Control which allows you 
to block unwanted TV usage based on US MOVIES and 
US TV PROGRAMS Ratings.
LOCK   
RECOGN I ZED
CHANGE  CODE : ADD / DLT   
CONT I NUE : SETEND       : ACT I ON         
CONF I RM   4-D I G I T   CODE
****
****
BACK  SPACE:ENTER  : 0 - 9  
END       : ACT I ON    
           LOCK   
ENTER  4-D I G I T   CODE
- -  
M A I N  MENU
DVDLOCK
CH
CLOCKTV
LANGUAGE
END         : ACT I ON SELECT  :                            SET : SET 
531
V-Chip Control Feature 
SURROUND
SELECT     SET CLEAR
ACTION
NUMBER
keys
Notes