Panasonic Tv Dvd Vcr Combination Pv Df2003 Operating Instructions

							21
Basic Operation
  Please read the disc jacket for operation information.
  If a single sided disc is placed in upside down, “THIS 
TYPE OF DISC CANNOT BE PLAYED. PLEASE 
INSERT A DIFFERENT DISC” is displayed.
  Remove disc and press unit POWER off when not in 
use.
  Disc continues to rotate with menu displayed even 
after play is done. Press STOP to clear menu display 
when  nished with menu.
■  Forward/Reverse rapid scene search 
     ➞ Press FF/SLOW+ or REW/SLOW- 
during play.
    
➞ Press PLAY to release.
  Starting forward/reverse search during play started from 
menu on Video CDs may recall menu.
  Search speed, slow at  rst, increases with each 
additional press of the button up to 5 levels.
  When    appears on the screen while a 
button is being pressed, it means that the 
corresponding operation is prohibited by the 
unit or the disc.
The unit memorizes the point where STOP is 
pressed (STOP    display on the screen). 
Press PLAY to resume play from this point. 
Pressing STOP again or opening the tray cancels 
RESUME, however, RESUME is not canceled 
when power is turned off and on.
  RESUME works only with discs for which elapsed 
play time is displayed during play.
RESUME function
Power turns off after unit has been in Stop mode 
(DVD) for about 5 minutes.
Auto-Power Off function
1.Do steps 1-3 (previous page).
    When menu appears, press STOP.
2. Press NUMBER key(s) to select desired 
track (play begins).
   Check disc for track numbers.
   Press “1” to start at beginning of disc.
To Resume Menu use,
Press STOP, and press PLAY, then the menu 
appears. Now, go to step 4 (previous page).
Enjoy Video CDs featuring 
playback control without using 
menus (Video CDs only)
*Important: If a remote control button does not work when pressed, press the DVD button on the 
remote and try the button again.
Reverse Skip                Forward Skip
Chapter/Track Chapter/Track Chapter/TrackChapter/Track
Current playback position
■ Still (Pause) Picture
    
➞ Press STILL/PAUSE during play.
    
➞ Press PLAY to release
.
 DVD/Video CD : The unit will enter Still picture mode.
 CD : The unit will enter Pause mode.
■ Forward/Reverse Chapter/Track Skip 
    ➞ Press SKIP+ | or SKIP- | 
 during 
play.
     Each press skips a chapter (DVD) or track 
(Video CD/CD).
Pressing SKIP- | once midway through a 
chapter/track returns to start of that chapter/track. 
Each additional press skips back one chapter/track.
 Pressing SKIP+ | or SKIP- | during play 
started from menu on Video CDs may recall menu.
■ Frame by Frame picture (DVD/Video 
CD)
    ➞  Press STILL/PAUSE in Still mode.
     
➞  Press PLAY to release.
  Each press advances picture one frame.
  Hold down for consecutive frame advance.
  Whether pictures are advanced by “FRAME” or 
“FIELD” is selected automatically (see page 62).
■ Slow Motion picture (DVD/Video CD)
    
➞ Press FF/SLOW+ or REW/SLOW- (DVD 
only) in Still mode.
    
➞ Press PLAY to release.
  Slow motion speed, slow at  rst, is increased with 
each additional press of the button up to 5 levels.
  Reverse slow motion is not available for video CDs.
Notes 
						

							22For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
TV Operation
1
Press POWER* on the remote or unit.
■ Using the 100 key
When selecting CABLE channels 100 to 125 with 
the NUMBER keys,  rst press the 100 key, and 
then enter the remaining two digits.
■ Rapid Tune
Press R-TUNE to display the last channel you 
were watching.
■  Audio Mute
Press MUTE to instantly mute the sound. Press 
again to restore the previous sound level.
■ Phones
Connect an earphone (not supplied) or headphones 
(not supplied) to the Phones Jack.
*Important:  If a remote control button does not work 
when pressed, press the 
 button on the 
remote and try the button again.
  Use CH   
 or 
NUMBER keys to 
select a channel.
2
3
Press VOL + or 
VOL - to adjust 
volume.
24PHONES 
JackPOWERVOL+/VOL-
CH  
SURROUND
VOL +/-
RAPID 
TUNE POWER
MUTE
CH
 
100 key
NUMBER
keys
CH08
  Cable or antenna is connected.
  Power cord is plugged in.
 Check List 
						

							23
TV Operation
MTS Broadcast/TV Stereo System
Receivable  Broadcast Types
The following are possible audio broadcast types and 
on-screen displays. The signal being received is indicated with 
an “ 
   ” mark while the selected audio mode is indicated with 
an arrow. To change the audio mode for these broadcasts, see 
the “Audio Mode for TV Viewing” section below.
Press DISPLAY to display the broadcast signal being 
received.
MTS Stereo and SAP broadcastMulti-channel Television Sound Stereo 
(main language) and Secondary Audio 
Program (sub language) broadcasts 
are being received simultaneously. 
Select the STEREO or SAP audio 
mode.
MTS Stereo broadcast
Multi-channel Television Sound Stereo 
broadcast. Select STEREO audio 
mode.
 If stereo broadcast is weak and the 
display  ickers, select MONO audio mode 
for possible improvement.
SAP broadcastSecondary Audio Program (sub 
language). Select SAP audio mode for 
the sub language.
  Audio Mode for TV Viewing
Press  AUDIO to select the desired audio mode as described above.
(Arrow shows selection.)
 Each press of AUDIO will change the audio mode as shown below.
 “SAP” is selected with  rst press of AUDIO.
MONO broadcastNormal monaural sound broadcast.
1 2 : 0 0AMCH08STEREOSAPMONOSP
1 2 : 0 0AMCH08STEREOSAPMONOSP
STEREOSAPMONO
1 2 : 0 0AMCH08SP
STEREOSAPMONO
1 2 : 0 0AMCH08SP
< Example >
STEREOSAPMONO
Press AUDIO
Press AUDIO
Press AUDIO
Equipped with  
-TV Noise 
Reduction for true MTS 
reproduction. 
  -TV Noise 
Reduction is required for good 
stereo separation and audio  delity.
 
 is a registered trademark, 
and is licensed by    
Technology Licensing. 
STEREOSAPMONO
STEREOSAPMONO
SURROUND
AUDIO
DISPLAY 
						

							24For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
  Closed Caption Mode Feature
1
Closed Caption is ...This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes 
useful information from TV stations available to everyone.
Press ACTION* to display MAIN MENU.Closed Caption Mode Selections 
Caption Mode: CAP C1 or C2
A narration of selected TV 
programs is displayed. 
Check TV program listings for CC 
(Closed Caption) broadcasts.
Caption Mode: TEXT C1 or C2
Most of the screen will be blocked 
out. When the TV station 
broadcasts information, such as 
program listings, it will appear in 
this space.
Caption Mode: OFF
Closed Caption/Text narration will 
not be displayed.
Recording and Playing Back a Closed Caption/Text Program
Record     :  Record normally. Closed Caption/Text signal, if present, is recorded 
automatically.
Playback :  Start playback. Perform above steps to select desired caption mode.
5
Press ACTION three times to return to 
the normal screen.
2
1) Press       
 
to select “TV.”
2) Press SET to 
display SET 
UP TV screen.
3
1) Press     to 
select 
“CAPTION.”
2) Press SET to 
display 
CAPTION 
screen.
OFFCAP  C1
TEXT  C1CAP  C2TEXT  C2
4
1) Press   to 
select 
CAPTION 
MODE.
2) Press SET 
repeatedly to 
select mode. 
(See left.)CAPT I ONCAPT I ON  MODE      :    CAP   C1
CC  ON  MUTE          :   CAP   C1  
SET          : SET   SELECT  :                                  
END          : ACT I ON   
M A I N  MENU
DVDLOCK
CH
CLOCKTV
LANGUAGE
END         : ACT I ON SELECT  :                            SET : SET 
531
Closed Caption System
 The closed caption or text signal may 
be broadcast over C1, C2, or both. 
Also, text contents can vary so you 
may wish to try different settings. 
  While recording one station and 
watching another, Captioning will 
not be displayed.
SELECT :          
END       : ACT I ON      
              SET  UP  TV   
SET : SET
CAPT I ON    I NPUT  SELECT       : TUNER SET  UP  V I DEO / AUD I ODVD  VOL  ADJUST   : + 2FM  ANTENNA            :  I NTREMOTE  WARNING     : ON
Notes 
						

							25
TV Operation
1
  Caption On Mute Feature
Closed Caption narration, if available, is displayed when 
MUTE button is pressed for silence. 
Press ACTION to display MAIN MENU.
  When a disc supporting closed caption is 
used, the subtitle and the closed caption 
may overlap. In this case, turn the subtitle 
or caption on mute mode off. (See page 
48.)
2
1) Press    
  
 to select 
“TV.”
2) Press SET to display 
SET UP TV screen.
6
Press ACTION three times to return to the normal 
screen.
7
Press MUTE to mute the sound and display 
closed captioning.
 To cancel, press MUTE again.
3
1) Press   
 to select 
“CAPTION.”
2) Press SET to display 
CAPTION screen.
M A I N  MENU
DVDLOCK
CH
CLOCKTV
LANGUAGE
END         : ACT I ON SELECT  :                            SET : SET 
531
4
1) Press    to select 
CAPTION MODE.
2) Press SET repeatedly 
to select “OFF.”
NOCAP C1
CAP C2
5
1) Press   
 to select CC 
ON MUTE.
2) Press SET repeatedly 
to select desired mode.
 Each press of SET will 
change the display as shown 
left. 
  The caption may be broadcast 
over CAP C1 or C2.
CAPT I ONCAPT I ON  MODE      :    OFF
CC  ON  MUTE          :   CAP   C1  
SET          : SET      SELECT  :                                  
END          : ACT I ON 
*Important: If a remote control button does not work when pressed, press the  button on 
the remote and try the button again.
SELECT :          
END       : ACT I ON      
              SET  UP  TV   
SET : SET
CAPT I ON    I NPUT  SELECT       : TUNER SET  UP  V I DEO / AUD I ODVD  VOL  ADJUST   : + 2FM  ANTENNA            :  I NTREMOTE  WARNING     : ON
SURROUND
MUTE
ACTION SELECT
     SET
Note 
						

							26For assistance, please call : 1-800-211-PANA(7262) or send e-mail to :\
 [email protected]
TV Timer Features
1
ON-TIMER with Alarm
This unit can be set to automatically power on in one of 
4 modes (TV, VCR Playback, FM radio, or DVD/Video 
CD/CD.) You can also combine the On-Timer with a 
one minute alarm that gradually increases in volume.
  If no button on the remote or unit (including a  button used to turn off the alarm) is pressed 
within 60 minutes after unit turns itself on, it will 
turn itself back off.
Press PROG* to display SET PROGRAM 
screen.
To Cancel ON-TIMER,
Repeat steps  1 and  2. Then,  press ADD/DLT  to clear 
the time in step  3. Now,  press PROG  to end.
“ON TIMER END” brie  y appears on-screen.
2
1) Press   to select 
“ON TIMER.”
2) Press SET  to 
display ON TIMER 
screen.
SET          :  SET SELECT  :            
END          :  PROG 
SET   PROGRAM
T I MER   PROGRAMM I NGON   T I MER
S LEEP     T I MER : 00
3
 ON-TIMER mode 
selection order
1) Press   to select 
desired settings.
2) Press SET  to set 
the ON-TIMER 
time or ON-TIMER 
mode.
 Make sure a tape is 
inserted if Playback 
mode is selected.
  Make sure a disc is 
inserted if DVD 
(DVD/Video CD/CD) 
mode is selected.
 See “FM Radio” on pages 
28 and 29 for instructions 
on how to preset FM 
stations.
4
Press   to select 
ALARM “ON” or 
“OFF.”
When “ON” is selected,
an alarm will gradually increase in volume for one 
minute or until canceled by pressing any button 
(including VOL + -).
To Make Corrections,
use 
   and      to move back and correct.
5
Press PROG  to set ON TIMER. “ON TIMER  SET” is displayed. 
  ON-TIMER Indicator lights up on the unit.
Sleep Timer 
This unit can be set for auto power off.
Press PROG  to display SET 
PROGRAM screen.
1
To cancel, 
press SET  repeatedly until 00 appears.
2
1) Press  to 
select SLEEP 
TIMER.
2) Press SET 
repeatedly to 
select the 
desired time.
3
Press PROG  to return to the normal 
screen.
 Pressing DISPLAY  with sleep timer set 
displays remaining time.
ON  T I MER
SELE CT  HOUR
SET          : SET       SELECT  :                                  
END          : PROG 
ALARM : ON
ON  T I MER
SELE CT  ALARM
SET       : SET                BACK :       SELECT  :                              
END          : PROG 
ALARM : ON
CANCEL  : ADD / DLT     
SET          :  SET SELECT  :            END          :  PROG 
SET   PROGRAM
T I MER   PROGRAMM I NGON   T I MER
S LEEP     T I MER : 00
SLEEP TIMER    30     60     90     00
FM1VCRCH01
CH125
FM8
FM9CH02CH03
DVD
ON-TIMER Indicator
Note
  The clock is set to the correct time.
 Check List 
						

							27
TV Operation
TV/VCR Status & Clock Display
Press DISPLAY to display or remove the overlay.
 
Blue Screen Display
When a function button is pressed (PLAY, FF, etc.) or you 
change channels, the unit mode or channel number will be 
displayed.
  Channel & Function Display
PLAY
Whenever a blank section of a tape comes up in Playback 
mode, or when the selected channel has no broadcast signal 
with the Weak Signal Display Feature set to “OFF” (see page 
38), the screen will turn solid blue.
REC         1 2 : 0 0PM0 : 25CH08-0 : 1 2 : 3 4 SPSTEREOSAPMONO
*Important: If a remote control button does not work when pressed, press the  button on the remote and try 
the button again.
SURROUND
PROG SELECT
     SETADD/DLT
DISPLAY
On-Screen Display (OSD)
CH08
Function Status
Current Time
Rec Time 
Remaining 
(OTR mode 
only, see page 
18.)Counter
Tape 
Speed
(See 
page 4.) Receivable 
Broadcast 
Types (See 
page 23.)
Channel 
						

							28For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
1) Press CH  to 
select the desired 
radio station. 
(Each 
press changes 
frequency by 200 
kHz.)
2) Press ADD/DLT to 
set the radio 
station.
FM Radio
FM  1     87.  5MHz
1 2 : 0 0PM
FM  1     8 7. 7MHz
MEMORY : PRESS  ADD / DLT  KEY
1 2 : 0 0PM
FM  1     8 7. 7MHz
MEMOR I ZED
1 2 : 0 0PM
M A I N  MENU
DVDLOCK
CH
CLOCKTV
LANGUAGE
END         : ACT I ON SELECT  :                            SET : SET 
531
2
Press a NUMBER 
key (1~9) to select the 
FM preset number.
1
To Make Corrections, 
select station with a 
NUMBER key, then do step 
3 again. 
To exit FM mode, press 
 or DVD on the remote 
or TV/FM on the unit.
3
FM Radio Setup
Press FM* on the remote or TV/FM on the 
unit to display FM radio mode.
FM Radio is ...This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1 
MHz. You can set the On-Timer (page 26) to wake up to your favorite radio station.
FM Antenna Setup
1
2
Make sure FM tuning is done correctly (see FM 
Radio Setup).
Press ACTION to display MAIN MENU.
1) Press   to 
select “TV.”
2) Press SET to 
display SET UP TV 
screen.
Continued on next page.
CH   
TV/FM
Hold down CH  or  for a few seconds, 
then release to 
quickly scan for FM 
stations in your area.
 To cancel, press CH  or  while in search 
mode. 
						

							29
TV Operation
3
4
■For cable TV users➞ “INT”
■For antenna users
➞ “EXT”
2 1
To exit FM mode, 
press  or DVD on the remote or TV/FM 
on the unit.
Press a NUMBER 
key (1~9) to select 
a preset FM number 
(see FM Radio Setup 
on page 28).
Using FM Radio
Press ACTION twice to end setup.
Press FM on the remote or TV/FM on the 
unit to display FM radio mode.
 FM radio cannot be recorded on a Video 
cassette.
 You may get better reception by 
repositioning the unit.
 You cannot select FM Radio mode during 
playback or record, or while a blue back 
screen (PROG, ACTION, MENU) is 
displayed.
 Once stations are set, the selected station 
and current time are displayed when FM 
Radio mode is entered. To remove time, 
press DISPLAY. If DISPLAY is pressed 
again, the unit status screen appears.
*Important: If a remote control button does not work when pressed, press the FM button on the 
remote and try the button again.
  Audio Mode for  FM Radio
Press AUDIO repeatedly 
to select “STEREO” or 
“MONO” in FM Radio 
mode.1) Press 
 to 
select FM 
ANTENNA.
2) Press SET to 
select “INT  
(INTERNAL)” or 
“EXT 
(EXTERNAL)” to 
determine which 
one sounds best.
FM  1     87.  5MHz
1 2 : 0 0PM
STEREOMONOFM  1     8 7. 7MHz
1 2 : 0 0PM
SELECT :          
END       : ACT I ON      
              SET  UP  TV   
SET : SET
CAPT I ON  
 I NPUT  SELECT       : TUNER SET  UP  V I DEO / AUD I ODVD  VOL  ADJUST   : + 2FM  ANTENNA            :  I NTREMOTE  WARNING     : ON
SURROUND
ACTION SELECT
     SET TV-VCR
DISPLAY
DVD
FM
CH
 
NUMBER
keys
ADD/DLT
AUDIO
Notes 
						

							30For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Timer Recording
Press PROG to end 
the program. 
To Enter More 
Programs, 
press 
 to select 
and SET to set a 
blank program 
number, and then 
repeat step 3.
Press PROG twice to exit this mode.  If you’re using a cable box, make sure that it is tuned 
to the desired channel and the power is left on for 
timer recording.
  PROG TIMER Indicator lights up on the unit.
You can set up to 8 programs to be recorded while you 
are away.
1
2
3
Press PROG* to display SET PROGRAM 
screen.
1) Press  to 
select TIMER 
PROGRAMMING.
2) Press SET to 
display screen.
  If a program is already in memory, press   
, and 
SET to select an unused  program number.
Press  to select 
and SET or 
  to 
set the recording 
DATE.
  1~31 = One time 
  DAILY = MON~FRI
  WEEKLY SUN~SAT = 
Same time once a week
Repeat step 3 to set:  Start time, Stop time
  Channel (or LINE for outside source) 
  Speed (SP, LP, SLP)
Today’s 
Date
Example
4
5
DAILY72
1
31
68    9
SELECT     /      Selection Order
WEEKLY
(SAT)WEEKLY
(MON)WEEKLY
(SUN)
CANCEL : ADD / DLT SELECT   1 - 8 :         ENTER   : SET END       : PROG     
P  DT  START    STOP    CH  SPD
1            day  9 : 00 p  12 : 00a  08     SP
2   -- -- : --   -- : --  --  --3   -- -- : --   -- : --  --  --4   -- -- : --   -- : --  --  --
SET          :  SET SELECT  :            
END          :  PROG  SET   PROGRAM
T I MER   PROGRAMM I NGON   T I MER
S LEEP     T I MER : 00
SELE CT  START  DATE
7  FR I  --:--   --:--  --TODAY DATE START ST
OPCH
SP
SELE
CT :          SET       : SET     
END       : PROG  
- - - - - - - - -- - - - - - - -- - - - - - - 
PROG TIMER  Indicator 
  Cable or antenna is connected.
  Power cord is plugged in.
  The clock is set to correct time.
  The tape is long enough.
  The record tab is in place.
 Check List