Panasonic Tv Dvd Vcr Combination Pv Df2003 Operating Instructions

31
Timer Operation
Repeat steps 1 and 2 on page 30.
1
Press PROG twice to exit this mode.
2
3
To Clear program...
4
Press  to select 
the desired program.
  
1) Press SET to 
display.
2) Press 
 to 
select and press 
SET or 
 
  
 to set 
new program 
contents.
3) Press PROG.
Cancel a Timer Recording: 
(Recording is in progress)
 
Hold down STOP for a few 
seconds to cancel the Timer 
Recording.
 Any future daily or weekly recordings will 
be performed as programmed.
Press ADD/DLT.
Review, Replace or...

32For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Universal Remote Control is...The Remote Control may be set up to control some basic 
DSS or Cable box functions.
The Universal Remote Control Setup
1
Press   , FM, DVD or DSS CABLE on the remote 
control to select the desired mode. (See below for buttons 
available in each mode.)  Once the remote control has been properly set up, you can 
select TV-VCR, FM, DVD, DSS or CABLE mode depending 
on which...

33
Advanced Operation
  In DSS or CABLE mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection.
  In DSS or CABLE mode, POWER, CH Up/Down, NUMBER Keys, ACTION, PROG, DISPLAY/ENTER, 
SEARCH/SKIP- 
|, R-TUNE, SELECT, SET, CM SKIP/ZERO/SKIP+ |, COUNTER RESET/ZOOM, ANGLE, 
AUDIO, TITLE, SUB TITLE, MENU, or ADD/DLT are not available. Press   , FM, DVD to use these functions.
  Depending on your DSS receiver or Cable box brand, some of the functions listed may not be...

34For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Search System is ...Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are 
made, program index and information are also included. These index marks can be used to access or 
scan recordings.
1
Press SEARCH* 
in Playback or 
Stop mode to 
display INDEX 
SEARCH screen, 
and then press 
NUMBER keys to 
select the 
recording number.
 To calculate 
number,...

35
Advanced Operation
*Important: If a remote control button does not work when pressed, press the  button on the 
remote and try the button again.
Repeat Play
Set to see a recording over and over.
PLAY REPEAT  ON
To turn “ON,”press PLAY/REPEAT on the unit  repeatedly 
in Playback mode to select “REPEAT ON.”
To turn “OFF,”repeat above to select “REPEAT OFF.”
  Playback repeats when tape end is reached or 
an unrecorded portion longer than 30 seconds is 
detected.
  For repeat play in DVD mode, see page...

36For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Press  COUNTER 
RESET at the 
desired position to 
reset to “0:00:00.”
Tape Operation (continued)
Zero Search
To quickly return to a speci c tape counter 
location. 
1
2
Press STOP.
4
5 3
Continue playback, rewind, or fast 
forward.
Press DISPLAY* during playback to 
display the Counter.
Press  CM/ZERO in stop mode to start 
ZERO SEARCH.
0 : 00 : 00SLP
PLAY  12 : 00   PM
  Unit goes into FF or REW...

37
Advanced Operation
Press  CM/ZERO repeatedly to select skip time in 
Playback mode.
  Commercial Skip
By pressing the CM/ZERO button in Playback mode you 
can skip over 1 to 3 minutes of recorded tape in just a few 
seconds.
  No indication appears.
■  Auto Shut Off 
No broadcast signal in TV mode (Only when Weak Signal 
Display is set to OFF.), DVD stops, or blank tape is played 
for 5 minutes. 
➞ Power turns off   This feature is canceled if any button is pressed during above 
conditions.
■ Auto...

38For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
When “ON” is selected, the picture is displayed 
even when a broadcast signal is weak or 
non-existent.
Weak Signal Display Feature
1
2
3
  “ON”  =  Picture is displayed regardless of signal 
condition, and may not always be clearly 
visible.
  “OFF” =  Screen turns solid blue when signal is absent 
or weak.
  If unit is connected to equipment which has blue back 
feature, selecting “ON” will have no...

39
Advanced Operation
VCR Lock
All operations are prohibited except Timer 
recording and tape eject. Useful for families with 
small children.
In Stop mode, hold 
down REC on 
the unit without a 
cassette inserted for 7 
seconds to turn “ON.” 
(Please ignore “NO 
CASSETTE” warning.)
Repeat above with or 
without cassette to turn 
“OFF.”
  VCR Lock is canceled automatically after about 24 
hours if clock is set.
*Important: If a remote control button does not work when pressed, press the  button on the...

40For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Press ACTION* to display MAIN MENU.
Enter Secret Code
A 4-digit code must be entered to view a blocked 
program or change rating settings.
1
  Some rental movies do not include V-Chip 
data.
  DO NOT forget your secret code.
  Once ratings are set, restricted tapes or 
programs cannot be accessed unless the 
secret code is entered.Changing your secret code
 You will need your current code.
Do steps...