Panasonic Tv Dvd Vcr Combination Pv Df2002 Operating Instructions

31
Timer Operation
Repeat steps 1 and 2 on page 30.1
Press PROG twice to exit this mode.
2
3
To Replace program...
To Clear program...
4
Press  to select
the desired program.
1)Press SET to display.
2)
Press  to select
and press SET or
  to set new
program contents.
3)Press PROG.
Cancel a Timer Recording:
(Recording is in progress)
Hold down STOP for a few seconds
to cancel the Timer Recording.
• Any future daily or weekly recordings
will be performed as programmed.
Press ADD/DLT.
Review, Replace or...

32For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Universal Remote Control is...
The Remote Control may be set up to control some
basic DSS or Cable box functions.
The Universal Remote Control Setup
1
Cable Box Universal Remote Control Feature
Press , FM, DVD or DSS CABLE on the
remote control to select the desired mode. (See below
for buttons available in each mode.)Once the remote control has been properly set up,
you can select TV-VCR, FM, DVD, DSS...

33
Advanced Operation
• In DSS or CABLE mode, it may be necessary to press ENTER after pressing number
keys for channel selection.
• In DSS or CABLE mode, POWER, CH Up/Down, Number Keys, ACTION, PROG,
DISPLAY/ENTER, SEARCH/SKIP-, R-TUNE, SELECT, SET, CM SKIP/ZERO/SKIP+,
COUNTER RESET/ZOOM, ANGLE, AUDIO, TITLE, SUB TITLE, MENU, or ADD/DLT are
not available. Press 
, FM, DVD to use these functions.
• Depending on your DSS receiver or Cable box brand, some of the functions listed may not
be remote...

34For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Search System is ...Each time a recording is made, an invisible index mark is placed on the tape.
When timer recordings are made, program index and information are also included.
These index marks can be used to access or scan recordings.
Tape Operation
• Make each entry within 5 minutes,
or the Index Search mode will be
canceled.
• If Index Search is started very close
to an index mark, that index...

35
Advanced Operation
Program End Search
Locates end point of recording for continuity.
Press SEARCH twice in Playback or
Stop mode to display PROGRAM
END SEARCH screen .
1
SEARCH  START : FF
EX
 I T    :   SEARCH   
PROGRAM END SEARCHPress FF
to start search.
Example of Program End Search operation.
Fig.1
Fig.2
Fig.3If search exceeds a few seconds in BLANK area.
  PLAYBACK DIRECTIONProgram 1
Program 2 or BLANKINDEX
Program 2 
BLANKINDEXBLANKProgram 1 
         Program 2
BLANK         Program 1INDEX...

36For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Tape Operation (continued)
Repeat Play
Set to see a recording over and over.
Zero Search
To quickly return to a specific tape counter location.
1
2
Press STOP.4
53
Continue playback, rewind, or
fast forward.
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
Press DISPLAY* during playback
to display the Counter.
Press CM/ZERO in stop mode to
start ZERO SEARCH.
0 : 00 : 00
PLAY REPEAT...

37
Advanced Operation
Press CM/ZERO repeatedly to select skip
time in Playback mode.
Commercial Skip
By pressing the CM/ZERO button in Playback mode
you can skip over 1 to 3 minutes of recorded tape in
just a few seconds.
• No indication appears.
Auto Shut Off
➔ Power turns off

Auto Playback
Insert a tape in Power off mode


Tape reaches its end
➔ Rewind, ➔ Stop

Playback Auto Eject 
(Repeat Play is “OFF”)Tape with no record tab reaches its end
➔ Rewind, ➔ Stop, ➔ Eject
Auto Operation Functions...

38For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Special VCR Features
Channel Caption is ...Station names, e.g. ABC, CNN, etc.
are set so they will appear when a
channel is selected. Choose 24
Ready Checklist
You need a list of stations and the
channel numbers you receive them
on.
ANTENNA  :   CABLE
AUTO   SETCHANNEL  CAPT I ONWEAK  S I GNAL   D I SPLAY : OFF
SELECT :          SET       : SET      
END       : ACT I ON   
           SET  UP  CHANNEL...

39
Advanced Operation
Remote Warning Feature
1
Press ACTION twice
to return to normal screen.
When Universal Remote Control (page 32) is
used, and this feature is set to “ON,” a warning
appears whenever an invalid key is pressed in
DSS or Cable mode.
2
43
Press ACTION
to display MAIN MENU.
1)Press 
  to
select “TV.”
2)Press SET to
display SET UP
TV screen.
1)Press 
 to
select REMOTE
WARNING.
2)Press SET to
set “ON” or
“OFF.”
•“REMOTE WARNING : OFF”
 Remote warning will not appear even if
invalid key is...

40For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V-Chip Control Feature
Press ACTION*
to display MAIN MENU.
Secret Code
V-Chip Control Feature is...This unit has a built-in V-Chip Control which allows
you to block unwanted TV usage based on
US MOVIES and US TV PROGRAMS Ratings.
A 4-digit code must be entered to view a blocked
program or change rating settings.
1
• Some rental movies do not
include V-Chip data.
• DO NOT forget your secret code.
• Once...