Panasonic Th 50pf20 Operating Instructions

3D Y/C FILTER (NTSC) 
COLOR SYSTEM 
SIGNAL 
ON 
AUTO 
3 : 2 PULLDOWN OFF 
[ 
VIDEO ] 
3 : 2 PULLDOWN OFF 
XGA MODE
AUTO
51
3:2 PULLDOWN
COLOR SYSTEM
Select SIGNAL from the “SET UP” menu during Video (S Video) input signal mode. 
(“SIGNAL [VIDEO]” menu is displayed.)
SET UP for Input Signals
Press to select the “COLOR SYSTEM” .
Press to select each function.
If the image becomes unstable:
With the system set on Auto, under conditions of low level or noisy 
input signals the image may in rare cases become...

ADVANCED NR[ 
VIDEO ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
Digital ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
COMPONENT ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
RGB ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
()NOISE REDUCTION
OFF 
()NOISE REDUCTION
ADVANCED
52
VIDEO NR:        Automatically reduces unwanted picture noise.
MOSQUITO NR: Reduces mosquito noise around subtitles on MPEG videos.
BLOCK NR:      Reduces block noise when playing MPEG videos.
Note:...

SYNC
SIGNAL[ 
RGB ]
3 : 2 PULLDOWN
XGA MODEAUTO
OFF
AUTO
H-FREQ.
V-FREQ.kHz
Hz 63.98
60.02
SIGNAL FORMAT 1280×1024/60
V-FREQ. Hz60.02DOT CLOCK FREQ.MHz 108.0
SIGNAL FORMAT 1280×1024/60
3 : 2 PULLDOWN
SIGNAL
OFFSDI THROUGH
OFF
[ 
Digital ] 
NOISE REDUCTION
OFF
53
SET UP for Input Signals
This function operates only during input from PC IN terminal.
Select SIGNAL from the “SET UP” menu during RGB or Component input signal.
SYNC
Displays the frequency and the type of the current input signal.
This display...

MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUP
NETWORK SETUP
DISPLAY ORIENTATION
Landscape MULTI PIP SETUP
PORTRAIT SETUP
2/2 SETUP
--:--:--:--:--:--
DHCP
NETWORK SETUP
SAVE
0
192.168.    0.    8
255.255.255.    0
192.168.    0.    1
1024
Auto
RS-232COff
SUBNET MASK
LAN SPEED GATEWAY IP ADDRESS
PORT
CONTROL I/F SELECT NETWORK ID
MAC ADDRESS
Network Setup
Make the various settings to use the network function.
  
DHCP, IP ADDRESS, SUBNET MASK, and GATEWAY settings
1 Set DHCP.
     When “OFF” is...

Options 
Weekly Command TimerAudio input select
1/3 
 
Initial input Onscreen displayOn
Off
Off Off
0 0Maximum VOL level Initial VOL levelOffInput lockOffButton lockOffRemocon User level
Options 
Enable Off-timer function Normal Initial Power Mode 0 ID select Off Remote ID Off Serial ID Off Display size Off Studio W/B Off Studio Gain 
2/3 
 
3/3 Options 
O f f 
Off
Off Clock Display
Rotate
Off All AspectManual Auto Setup Slot power 
Off
Power On Screen Delay
55
Item Adjustments
Weekly Command TimerSets...

56
Item Adjustments
Input lockLocks the input switch operation.
Off 
 PC  SLOT INPUT*1  VIDEO  COMPONENT*2  HDMI  DVI
*1 “SLOT INPUT” is displayed when an optional Terminal Board is installed.
 When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed.*2  “COMPONENT” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”. (see page 49)Notes:
• Only the adjusted signal is displayed (see page 16).
• Input switch can be used when...

57
Item Adjustments
Studio W/BOff:  Nullify all the settings adjusted.
On:  Sets the color temperature for TV studio.
Note:  Valid only when the “WARM” is set as “COLOR TEMP” in PICTURE menu.
Studio GainSharpens the contrast for a better view when a part of the image is too light to see.
Off:  Disables “Studio Gain”.
On:  Enables “Studio Gain”.
Note:  This setting is valid only when the input signals are as follows:
    Component Video, RGB (analog), SDI, HDMI
Slot powerOff 
 Auto  On 
Off:  Power is not...

Weekly Command Timer 
20:00 
20:30 57 
58 
8/8 
 
22:00 59 --:-- 60 --:-- 
--:-- 61 --:-- 62 --:-- AVL:00 
DAM:NORM 
POF 
--- 
--- 
---  --- 
--- 63 64 
1Program
Weekly Command Timer 
8:00 
10:30 02 01
1/8 
 
--:-- 03--:-- 04--:-- 
--:-- 0512:00 069:12 PON
IMS:SL1 
--- 
--- 
--- 
---  DAM:ZOOM 
AVL:10 0708
1Program
58
Options Adjustments
Weekly Command Timer
You can set 7-day timer programming by setting time and command.
Note: 
Before setting Weekly Command Timer, set PRESENT TIME SETUP.  (see page 35)...

Weekly Command Timer 
0210:30 Command No Time IMS:SL1 Command 
1Program
Weekly Command Timer 
Command 
02Command No 
IMS:SL1 10:30 Time 
1Program
59
Options Adjustments
Press to select Command No.
Press to select a command number.6
Press to select Time / Command.
Press to set each item.
Time:  Set the time to execute a command program.
      Pressing “
” or “” button once changes “Time” 1 
minute.
     Pressing “
” or “” button continuously changes “Time” by 15 minutes.
Command:  Select a command to...

60
Options Adjustment
Set up the sound when an image input is selected.
Image input  Audio input
[SLOT INPUT]*1  SLOT INPUT / VIDEO / COMPONENT / DVI / PC / NO AUDIO
[VIDEO]  SLOT INPUT / VIDEO / COMPONENT / DVI / PC / NO AUDIO
[COMPONENT]*2  SLOT INPUT / VIDEO / COMPONENT / DVI / PC / NO AUDIO
[HDMI]  SLOT INPUT / VIDEO / COMPONENT / HDMI / DVI / PC / NO AUDIO
[DVI]  SLOT INPUT / VIDEO / COMPONENT / DVI / PC / NO AUDIO
[PC]  SLOT INPUT / VIDEO / COMPONENT / DVI / PC / NO AUDIO
  NO AUDIO: No audio input...