Panasonic Th 50pf20 Operating Instructions

11
HDMI connection
DVI-D IN connection
[Pin assignments and signal names]
1931
4218
Note: 
Additional equipment and HDMI cable shown are not supplied with this set.
Pin No.Signal NamePin No.Signal Name
1T.M.D.S Data2+11T.M.D.S Clock 
Shield
2T.M.D.S Data2 
Shield12T.M.D.S Clock-
3T.M.D.S Data2-13CEC
4T.M.D.S Data1+14Reserved 
(N.C. on device)
5T.M.D.S Data1 
Shield
6T.M.D.S Data1-15SCL
7T.M.D.S Data0+16SDA
8T.M.D.S Data0 
Shield17DDC/CEC 
Ground
9T.M.D.S Data0-18+5V Power
10T.M.D.S Clock+19Hot Plug...

Conversion adapter 
(if necessary)
Mini D-sub 15p
RGB
PC cableStereo mini plug (M3) Audio
Connect a cable which matches
the audio output terminal on the computer.
(Male)(Female)
COMPUTER
12
PC Input Terminals connection
Notes:
•  With regard to the typical PC input signals that are described in the applicable input signals list (see page 68), adjustment 
values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight 
PC input signal types that...

6789
1 3 4 52
COMPUTER
RS-232C Straight cable
D-sub 9p(Male)
(Female)
13
Connections
SERIAL Terminals connection
Notes:
•  Use the RS-232C straight cable to connect the computer 
to the Plasma Display.
•  The computer shown is for example purposes only.
•  Additional equipment and cables shown are not supplied 
with this set.
The SERIAL terminal conforms to the RS-232C interface 
speci cation, so that the Plasma Display can be controlled 
by a computer which is connected to this terminal.
The computer...

INPUT MENU ENTER/+/ VOL-/
14
Power Indicator
Remote Control Sensor
Power ON / OFF
Connecting the AC cord plug to the Plasma Display.
Connecting the plug to the Wall Outlet.
Note: 
When disconnecting the AC cord, be absolutely sure to 
disconnect the AC cord plug at the socket outlet  rst.
Press the Power switch on the Plasma Display to turn the 
set on: Power-On.
Power Indicator: Green
Press the  button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby) 
Press the...

PC
FULLNANODRIFT
English (UK) 
Deutsch 
Français 
 
Italiano 
 
Español 
 
ENGLISH (US) 
 
OSD LANGUAGE
SET  SELECT 
PRESENT TIME SETUP
PRESENT TIME OF DAY    MON  99:99
SET
PRESENT TIME OF DAY99:99DAYMON
PRESENT TIME SETUPPRESENT TIME OF DAY    MON  99:99
SET
PRESENT TIME OF DAY10:00DAYTUE
LANDSCAPE
PORTRAIT
DISPLAY ORIENTATION
15
From the second time on, the below screen is displayed for a while (setting condition is an example). When  rst switching on the unit
Following screen will be...

INPUT MENU  ENTER/ + /  VOL - / 
INPUT MENU ENTER/+/ VOL-/
16
Selecting the input signal
Notes:
•  Selecting is also possible by pressing the INPUT button on the unit.
•  Outputs the sound as set in “Audio input select” in the Options menu.(see page 60)
•  Select to match the signals from the source connected to the component/RGB input 
terminals. (see page 49)
•  In 2 screen display, the same input mode cannot be selected for the main picture and 
sub picture.
•  Image retention (image lag) may occur on...

17
INPUT MENU ENTER/+/ VOL-/
Basic Controls
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen 
will switch. (see page 24)
INPUT button (Input signal selection)
(see page 16) Main Power On / Off Switch
Power Indicator
The Power Indicator will light.
• Power-OFF ....Indicator not illuminated (The unit will 
still consume some power as long as the 
power cord is still inserted into the wall 
outlet.)
• Standby  ........ Red
Orange (When “Slot power” is set to 
“On”. See page 57)...

18
Basic Controls
Standby (ON / OFF) button
The Plasma Display must   rst be plugged 
into the wall outlet and turned on at the 
power switch (see page 14).
Press this button to turn the Plasma 
Display On, from Standby mode. Press 
it again to turn the Plasma Display Off to 
Standby mode.
ACTION button
Press to make selections.
ASPECT button
Press to adjust the aspect. 
(see page 19)
POS. /SIZE button 
(see page 26)
PICTURE button 
(see page 29)
Sound mute On / Off 
Press this button to mute the...

INPUT MENU  ENTER/ +/  VOL -/ 
19
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format 
picture.
Press repeatedly to move through the aspect options:
For details about the aspect mode, please see “List of Aspect Modes” (page 67). 
The aspect mode changes each time the ENTER button is pressed.
[During MULTI PIP Operations]
•  Picture and Picture, Picture in Picture  : 4:3 FULL
•  Others  :  Aspect switching is not possible....

20
You can display two pictures, such as a video image and computer image, in a two-screen display. (Use the remote control 
for this operation. It cannot be performed with the buttons on the main unit.)
MULTI PIP SETUP
Set the functions and mode for two-screen display in “MULTI PIP SETUP” in the SET UP menu.
(see page 46)
Selecting the Display Mode
 
Each time this button is pressed, the screen changes.
 
Note:
The screen changes in the same way when “DISPLAY MODE” in “MULTI PIP SETUP” is changed. (see...