Panasonic Th 152ux1 Operating Instructions

Press to select the input signal to be played back from the equipment 
which has been connected to the Plasma Display.
HDMI input terminal in HDMI 1.
HDMI input terminal in HDMI 2.
Input terminal in Terminal Board.*
4k2k HD-SDI input terminal in SDI IN.
4k2k DVI-D input terminal in DVI-D IN.
PC input terminal in PC IN.
*  “SLOT INPUT” appears when the Terminal Board is connected.
INPUT
HDMI1
HDMI2
SLOT INPUT
4K-SDI
PC 4K-DVI
Using dedicated buttons for input selection
MENU
ENTER/
INPUT
Press to select...

16
Normal Viewing Picture
Pos. /Size
Setup
Basic Controls
Main Unit
INPUT MENU
ENTER/
Right side 
surface
Remote control sensor
Main Power On / Off Switch Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The 
unit will still consume some 
power as long as the power 
supply is connected to the 
unit.)
• Standby  ........ Red
• Power-ON ...... Green
• PC Power management (DPMS)
 ......................... Orange (With PC input signal. 
See page 34)Up / Down button...

17
Basic Controls
Remote Control Transmitter
Standby (ON / OFF) button
The Plasma Display must  rst be turned
on at the power switch (see page 13).
Press this button to turn the Plasma 
Display On, from Standby mode. Press 
it again to turn the Plasma Display Off 
to Standby mode.
PC button
Press to select PC IN input. 
(see page 15)
SLOT buttons
Press to select SLOT Terminal Board. 
(see page 15)
SDI button, DVI button
Press to select SDI IN or DVI-D IN 
input. (see page 15)
SETUP button
(see page 34)...

ENTER/ 
Right side surface
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 
750 (720) / 60p • 50p]:
4:3 Full Zoom1
14:9 Just
Zoom2
Zoom3 4:3
16:9
4:3 Zoom16:9 For PC signal input: For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):4:3 Zoom116:9 Zoom2Zoom314:9Just
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 
750 (720) / 60p • 50p]:
4:3 Zoom16:9 For PC signal input: For SD signal...

19
Viewing 3D images
You can enjoy viewing 3D images with contents or programmes compatible with 3D effect by using the 3D eyewear 
(optional).
Note:
You need the 3D IR TRANSMITTER (optional) and the 3D eyewear (optional) to view the 3D images on this display.
For further information, see the instruction manuals of the 3D IR TRANSMITTER and the 3D eyewear.
This display supports “Frame Sequential
*1”, “Side by Side*2” and “Top and Bottom*3” 3D formats.
*
1:  The 3D format that the images for the left and...

20
Troubleshooting for 3D Eyewear 
Table of images that can be seen for each 3D Picture 
Format and the source image format
Symptoms Checks
Cannot see 3D images •  Has the 3D Eyewear been switched On?
•  Ensure that “3D Picture Display” in “3D Settings” is set to “3D”. (see 
page 35)
•  Some 3D image signals may not be automatically recognized as 3D 
images. Set “3D Picture Format” in “3D Settings” to match the picture 
format. (see page 35)
•  Check that there are no obstacles between the infrared...

21
Remote Control Unit
1Display the menu screen.                       
Press several times.
Each time the MENU button is pressed, the 
menu screen will switch.
2Select the item.
25
0
0
0
5
Picture
NormalNormaliseNormal
Brightness
Sharpness Picture Mode
Colour Contrast
Hue
Advanced settings
Memory save White balanceNormal
Memory load
Memory edit
(Example: Picture menu)
Select. Press.
 Select.
3Set.Adjust. Press.
 Adjust.
4Exit the menu.                       
Press several times.
Normal Viewing Picture...

Pos. /Size
Auto SetupH-Pos
Normalise
H-Size
V-Pos
V-Size
Clock Phase
Normal
0 0 0
0
Scaling ModeHV-FitOver scanOff
0
Dot Clock0
Clamp Position0
22
Adjusting Pos. /Size
1Press to display the Pos. /Size menu.
Press to select the menu to adjust.
Press to adjust the menu.
Press to exit from adjust mode.
3 2
Note:
If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture position will shift up or down. This picture 
position movement cannot be controlled by the Picture Pos./Size...

23
Adjusting Pos. /Size
H-PosAdjust the horizontal position.V-PosAdjust the vertical position.
H-SizeAdjust the horizontal size.V-SizeAdjust the vertical size.
Dot Clock (During RGB and PC input signal)
Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, 
adjust so that any such noise is minimized.
Clock 
Phase(During RGB and PC input signal)
Eliminate the  ickering and distortion.
Over scanTurn image over scan On/Off.
Con gurable signals are as...

24
Scaling 
ModeSelects the pattern to display the 1920 x 1080 (16:9) image on the 4096 x 2160 (17:9) display. 
The image size is adjusted according to the aspect mode and is enlarged horizontally or vertically, 
or its sides are masked.
Example: Aspect is 16:9
Scaling ModeVertically 
enlargedHorizontally 
enlargedSide masking Image
H-Fit
V: 16/15 times H: 16/15 times Not adjusted
V-Fit
V: Same size H: Same size Adjusted
HV-Fit
V: Same size H: 16/15 times Not adjusted
Note:
When the input signal is a...