Panasonic Th 152ux1 Operating Instructions

5
Safety Precautions
 Viewing 3D Content
Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc.
When preparing your own 3D content, ensure that it is properly produced.
Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other 
existing medical conditions.
Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other  
uncomfortable sensation.
Take an appropriate break...

6
Accessories Supply
Accessories
Fixing band × 3
TMME203Nut cover × 3
(M20)Nut cover × 3
(M16)
Batteries for the Remote 
Control Transmitter
(R6 (AA) Size × 2)Remote Control Transmitter
N2QAYB000560Operating Instruction book
Check that you have the accessories and items shown
Remote Control Batteries
Requires two R6 (AA) batteries.
1. Pull and hold the hook, then open the battery cover.2. Insert batteries - note correct polarity ( + and -).
Helpful Hint:
For frequent remote control users, replace old...

7
Connections
Video equipment connection
12
Pass the attached cable 
  xing band through the clip 
as shown in the  gure.To secure cables connected to Terminals, wrap the cable  xing band around them 
then pass the pointed end through the locking block, as shown in the  gure.
While ensuring there is suf cient slack in cables to minimize stress,  rmly 
bind all cables with the supplied  xing band.
To tighten: To loosen:
Pull
Pull Push the catch
  Cable  xing
  Secure any excess cables with band as...

8
Connections
Dual Link HD-SDI (4k2k) connection
LINK B INPUTLINK A  INPUT
AB
CD
LINK A
OUTLINK B
OUTLINK A
OUTLINK B
OUTLINK A
OUTLINK B
OUTLINK A
OUTLINK B
OUT
ABCD
1ch 2ch 3ch 4ch
• Recommended cable
  75  coaxial cable 5C-FB
•  Maximum extended length: 100 m
 *  When using a cable with a length of less than 
100 m and an attenuation of 20 dB at 750 MHz
Hardware with Dual Link HD-SDI output 
capability
Note:
Additional equipment and cables shown are not supplied with this set.
 

9
16 
17 24 
8 1 
9 
Connections
Single Link DVI-D (4k2k) connection
B
CD
A
Hardware with Single Link DVI-D output 
capability
Pin No.    Signal Name  Pin No.    Signal Name 
1T.M.D.S. data 2-13
2T.M.D.S. data 2+14+5 V DC
3T.M.D.S. data 2 shield15Ground 
416Hot plug detect 
517T.M.D.S. data 0-
6DDC clock18T.M.D.S. data 0+ 
7DDC data19T.M.D.S. data 0 shield
820
9T.M.D.S. data 1-21
10T.M.D.S. data 1+22T.M.D.S. clock shield
11T.M.D.S. data 1 shield23T.M.D.S. clock+
1224T.M.D.S. clock-
Notes:
•  Additional...

10
HDMI 
AV OUTHDMI 
AV  O U T
HDMI connection
DVI-D IN connection
[Pin assignments and signal names]
1931
4218
Note: 
Additional equipment and HDMI cable shown are not supplied with 
this set.
Pin No.Signal namePin No.Signal name
1T.M.D.S Data2+11T.M.D.S Clock 
Shield
2T.M.D.S Data2 
Shield12T.M.D.S Clock-
3T.M.D.S Data2-13CEC
4T.M.D.S Data1+14Reserved 
(N.C. on device)
5T.M.D.S Data1 
Shield
6T.M.D.S Data1-15SCL
7T.M.D.S Data0+16SDA
8T.M.D.S Data0 
Shield17DDC/CEC 
Ground
9T.M.D.S Data0-18+5V Power...

11
Connections
PC Input Terminals connection
Notes:
•  With regard to the typical PC input signals that are described in the applicable input signals list (see page 47), adjustment 
values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight 
PC input signal types that are not included in the list.
•  Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning 
frequency of 48 to...

6789
1 3 4 52
COMPUTER
RS-232C Straight cable
D-sub 9p(Male)
(Female)
12
SERIAL Terminals connection
Notes:
•  Use the RS-232C straight cable to connect the computer to the Plasma Display.
•  The computer shown is for example purposes only.
•  Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface 
speci cation, so that the Plasma Display can be controlled 
by a computer which is connected to this terminal.
The computer will require...

13
Power On / Off
Press the  button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the 
 button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the 
 switch on the 
unit, when the Plasma Display is on or in standby mode.
Note: 
During operation of the power management function, the power indicator turns 
orange in the power off state.
Turn on the breaker dedicated to the Plasma...

14
Power On / Off
Italiano 
 
Español 
 
ENGLISH (US) 
English (UK) 
Deutsch 
Français 
 
OSD Language
Set Select
When 3D images will be viewed by unspeci ed number of   
people or used for commercial applications, someone in
authority should convey the following precautions.
These precautions should be followed in the home as well.
3D Viewing/ 3D Content/ Viewing distance/ 3D Eyewear 
recommendations
 - To enjoy 3D images safely and comfortably, please
   read the Operating Instructions fully.
3D...