Panasonic Th 103pf12u Operating Instructions

1/2
SIGNAL
SCREENSAVER
EXTENDED LIFE SETTINGS
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABEL
POWER SAVE
SET UP
3D Y/C FILTER (NTSC)
COLOR SYSTEM
SIGNAL
ON
AUTO
3 : 2 PULLDOWN
Panasonic AUTO (4 : 3)OFF
4:3
[ 
VIDEO ]
NOISE REDUCTION
OFFREFRESH RATE
100 Hz
3 : 2 PULLDOWN
SIGNAL
OFF
[ 
Digital ] 
NOISE REDUCTION
OFF REFRESH RATE
100 HzH-FREQ.
V- F R E Q .kHz
Hz 63.98
60.02
DOT CLOCK FREQ.MHz 108.0
SIGNAL FORMAT 1280×1024/60
3...

3D Y/C FILTER (NTSC) 
COLOR SYSTEM 
SIGNAL 
ON 
AUTO 
3 : 2 PULLDOWN 
Panasonic AUTO (4 : 3) OFF 
4:3
[ 
VIDEO ] 
3 : 2 PULLDOWN OFF 
XGA MODE
AUTO
52
3:2 PULLDOWN
COLOR SYSTEM / Panasonic AUTO
Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input signal mode. 
(“SIGNAL [VIDEO]” menu is displayed.)
SET UP for Input Signals
Press to select the “COLOR SYSTEM” or 
“Panasonic AUTO  (4:3)”.
Press to select each function.
If the image becomes unstable:
With the system set on Auto, under conditions...

REFRESH RATE
100 Hzq
ADVANCED NR[ 
VIDEO ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
Digital ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
COMPONENT ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
RGB ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
()NOISE REDUCTION
OFF 
()NOISE REDUCTION
ADVANCED
53
VIDEO NR:        Automatically reduces unwanted picture noise.
MOSQUITO NR: Reduces mosquito noise around subtitles on MPEG videos.
BLOCK NR:      Reduces block noise when playing...

SYNC
SIGNAL[ 
RGB ]
3 : 2 PULLDOWN
XGA MODEAUTO
OFF
AUTO
SYNC 
AUTO 
SYNC 
ON G 
SYNC 
VBS 
H-FREQ.
V- F R E Q .kHz
Hz 63.98
60.02
SIGNAL FORMAT 1280×1024/60
H-FREQ.
V- F R E Q .kHz
Hz 63.98
60.02
DOT CLOCK FREQ.MHz 108.0
SIGNAL FORMAT 1280×1024/60
3 : 2 PULLDOWN
SIGNAL
OFFSDI THROUGH
OFF
[ 
Digital ] 
NOISE REDUCTION
OFF REFRESH RATE
100 Hz
54
SET UP for Input Signals
Select SIGNAL from the “SET UP” menu during RGB input signal.
SYNC
Setting RGB sync signal
Confi rm that the input is set to RGB INPUT...

Options 
Weekly Command Timer
1/3 
 
Initial INPUT Onscreen displayOn
Off
Off Off
0 0Maximum VOL level Initial VOL levelOffINPUT lockOffButton lockOffRemocon User level
Memory lock
Options 
Enable Off-timer function Normal Initial Power Mode 0 ID select Off Remote ID Off Serial ID Off Display size Off Studio W/B Off Studio Gain 
2/3 
 
3/3 Options 
O f f 
Off
Off Clock Display
Rotate
Off All AspectManual Auto Setup
Slot2 Serial Slot Select Slot power 
Off
Power On Screen Delay
55
Item Adjustments
Weekly...

56
Item Adjustments
INPUT lockOff 
 PC  INPUT1  INPUT2  INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 15).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
• In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value input in 
the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the...

57
Item Adjustments
Studio W/BOff:  Nullify all the settings adjusted.
On:  Sets the color temperature for TV studio.
Note:  Valid only when the “WARM” is set as “COLOR TEMP” in PICTURE menu.
Studio GainSharpens the contrast for a better view when a part of the image is too light to see.
Off:  Disables “Studio Gain”.
On:  Enables “Studio Gain”.
Note:  This setting is valid only when the input signals are as follows:
    Component Video, RGB (analog), SDI, HDMI
Slot PowerOff 
 Auto  On 
Off:  Power is not...

Options
On
Weekly Command Timer
Onscreen display 
1/3
Memory lock
Weekly Command Timer 
Program1MondayOnFunction
Program3Tuesday --- Wednesday Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
yProgram3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Weekly Command Timer 
8:00 
10:30 0102
1/8
--:-- 03--:-- 04--:-- 
--:-- 0512:00 069:12 PON
IMS:SL1 
--- 
--- 
--- 
---  DAM:ZOOM 
AVL:10 0708
1Program
Weekly Command Timer 
20:00 
20:30 57 
58 
8/8 
 
22:00 59 --:--...

Weekly Command Timer 
0210:30 Command No Time IMS:SL1 Command 
1Program
Weekly Command Timer 
Command 
02Command No 
IMS:SL1 10:30 Time 
1Program
1/2
SIGNAL
PC
OFF
STANDBY SAVEOFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABEL
POWER SAVE
SET UP
SCREENSAVER
EXTENDED LIFE SETTINGS
59
This function allows you to reset the unit to the factory setting.
Shipping condition
1
4Press to display the SET UP menu.
Press to select “OSD LANGUAGE”.
Press for...

60
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Checks
Picture Sound
InterferenceNoisy SoundElectrical Appliances
Cars / Motorcycles
Fluorescent light
Normal PictureNo SoundVolume
(Check whether the mute function has been activated on the remote control.)
No PictureNo SoundNot plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote...