Panasonic System Controller Wv Cu161c Operating Instructions

21
Alarm Buzzer Setting
This item lets you select whether or not to sound the alarm
buzzer when an alarm is activated.
1. Display the ALARM SETUP menu.
2. Select ALARM BUZZER by moving the joystick up or
down.
3. Select ALARM BUZZER ON or OFF by moving the joy-
stick to the right or left.
The initial factory setting is ON.
Note:The alarm buzzer time differs depending on (4) alarm
output setting.
Alarm Preset Position Setting
This item lets you preset a camera position to an alarm
input. The camera will...

System Setup
1. Display the WV-CU161C SETUP MENU.
2. Select SYSTEM SETUP by moving the joystick up or
down.
3. Press the PRESET/SET/PROGRAM PRESET button.
The SYSTEM SETUP menu appears on the monitor.
Cable Compensation Setting
This item lets you select a compensation level to match to
transmission loss caused by cable extension.
1. Display the SYSTEM SETUP menu.
2. Select CABLE COMP by moving the joystick up or
down.
3. Select the most appropriate cable length by moving the
joystick to the right or...

23
6. The text line LOADING blinks on the right while down-
loading.
The bar graph changing from 
to 
Pdisplays the down-
loading progress.
7. END appears on the right after downloading has been
completed. The progress bar disappears.
8. Editing the DATA TITLE.
For further information, refer to Data Title on the next
page.
Notes:
•Preset data for up to 8 cameras can be downloaded.
•Downloading time is approximately 2 minutes per cam-
era.
•Any previously preset data is overwritten by the down-
loaded...

•Check that the right unit address is selected for the
combination camera when using the RS-485 mode. The
camera cannot be operated if the numbers do not
agree.
Therefore, preset data cannot be uploaded.
•Error Display 
The following messages appear on the monitor when
errors occur during uploading.
Data Title
1. Display the PRESET DATA LOAD menu.
2. Select the desired CAM1-CAM8 position by moving the
joystick up or down.
3. Press the PRESET/SET/PROGRAM PRESET button.
The camera number and data title...

25
Parity Check 
This item lets you set the parity check mode for RS-485
communication.
1. Display the COMMUNICATION menu.
2. Select PARITY CHECK by moving the joystick up or
down.
3. Select NONE, EVEN or ODD for the parity check by
moving the joystick to the right or left.
The initial factory setting is NONE.
Note:This setting must be compatible with the peripherals
connected.
Stop Bit 
This item lets you set the number of stop bits for RS-485
communication.
1. Display the COMMUNICATION menu.
2. Select...

26
CAMERA CONTROL FUNCTIONS
Camera control functions are operable.
It is necessary to set up the camera before using the cam-
era control functions. For further information, refer to the
Operating Instructions for the respective combination cam-
era (See page 33). You can also set it up from the Camera
Setup menu during operating the system.
Pan/Tilt Control
A combination camera or an ordinary camera with pan/tilt
head can be controlled.
Move the pan/tilt head in the desired direction using the...

27
Auto Pan
The combination camera starts a specific panning mode
preset beforehand.
1. Press the AUTO/B/W/PATROL STOPbutton.
The auto panning function is activated.
The picture appears on the monitor.
The following functions may be also available depend-
ing on the combination camera.
AUTO PAN ON or functions set in the combination
camera:
Press the numeric button 1 and then press this
button.
AUTO SORT ON:Press the numeric button 2 and then
press this button.
AUTO SEQ ON:Press the numeric button 3 and...

28
Patrol Play
The combination camera reproduces a series of pan/tilt
movements and lens controls that have been preset before-
hand in Patrol Learning.
See page 33 to program the camera patrol learning func-
tion.
1. Press the PATROL PLAY/PATROL LEARNbutton.
The camera patrol picture appears on the monitor.
2. To stop the patrol play function, move the joystick.
Color or Black & White 
A black and white image is easier to view in dark places
while a colored image is better to use in the daylight....

29
Combination Camera Shortcuts
The combination camera is controlled using the hundred shortcuts shown in the table. While the SHIFT indicator is lit, type a
number using the numeric buttons, and then press the CAMERA FUNCTION button. [CAM FUNC] in the table below is an
abbreviation for the CAMERA FUNCTION button. For more details, refer to the Operating Instructions included with the cam-
era.
Selecting a PRESET position From #1 to #64
#1 [1] + [CAM FUNC]
#10 [1] + [0] + [CAM FUNC]
#64 [6] + [4] + [CAM...

30
External Device Control
Auxiliary Control
An auxiliary device connected to the Receiver or a camera
is controlled.
1. Press the WIPER/AUX1or DEF/AUX2button while the
SHIFT indicator is lit, to activate the connected device
to the receiver. 
The AUX1or AUX2indicator lights up.
2. To cancel the auxiliary control function, press the
WIPER/AUX1or DEF/AUX2button while the SHIFT
indicator is lit.
The AUX1or AUX2indicator goes off.
Camera Housing Control
Wiper Control
The camera housing provided with the...