Panasonic Sub Monitor Station Video Intercom System Vl Gm001a Installation And Operation Guide

11
3Install the bottom case to a wall using the wood screws
(4 mm x 35 mm, 3/16″ x 13/8″).
•Before drilling, see page 8 for installation location.

Introduction and Installation 

12
5Attach the wires that connect to the monitor station and sub monitor station to
the terminal. See page 16 for details on how to attach the wires.
•See page 9 for the wire type and distance.
•See the wiring schematic diagram on page 9.
4Attach the power cable to the terminal. See page 16 for details on how to attach
the power cable.
•If you want to use your own power cable, see page 9 for the type and distance.

Button
Power switch
•When the front case is
attached, the power
switch will be pressed...

13
•Check that there are no scraps from
the board or other debris in the
connector before installing it.
 Remove the front case from the bottom case
Bottom case
Front case
 While pushing the tabs at the top of the front case, pull the top of the front case
forward to disengage the front tabs one by one, and then pull the top of front
case forward to remove it.
 Remove the connector screw, and then remove the connector.
Do not pull the wire
when removing the
connector.
Introduction and Installation...

14
Introduction and Installation
Arrow mark
DC terminal AC adaptor
8Connect the power cable to the DC terminal, the power cord to the AC adaptor,
then connect the power cord to the AC outlet (100 V – 240 V, 50 Hz / 60 Hz).
•Be sure to connect the power cable to the 2 holes on the left side of the DC
terminal.
•For details on how to attach the power cable, see page 16.
DC terminal AC adaptor Power cord
To AC  outlet
Power cable
9Attach the DC cord to the clamp on the rear of the DC terminal.
• This will...

15
Introduction and Installation
To attach the AC adaptor and the DC terminal to a wall
By placing the AC adaptor and the DC terminal in the case and mounting the case
to the wall, you can protect the AC adaptor and the DC terminal from tampering and
exposure.
1Attach the rear part of the case to a wall using the wood screws (4 mm x 16 mm,3/16″ x 5/8″). Note:
• Disconnect the DC cord from the clamp on the rear of the DC terminal beforehand.
See step 9 on page 14 for details.
• Take out the cardboard and...

16
To attach the wires
•Strip off of the wire cover so that about 9 mm (
3/8″) of the wire is exposed.
•While pressing on the button with a pointed object such as a screwdriver, insert
the wire into the terminal connector.
•To disconnect a wire, press on the button while pulling out.
Introduction and Installation
Note:
• To open the case again, push the bottom of the front case, then release from the
rear case.
To attach the power cable
•While pressing on the button hard with a pointed object such as a...

17
Important information:
•Do not use anything containing alcohol, polish powder, powder soap, benzine,
thinner, wax, petroleum, or boiling water. Also do not spray with insecticide, glass
cleaner, or hair spray. This could cause a change in color or quality. Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit
with a slightly damp cloth.
Cleaning
Help 

18
Technical data about this product
General Information
Sub Monitor station
Power supply:
Current consumption:
Dimensions:
Mass (Weight):
Operating environment:
Installation method:
External material:24 V DC
Standby: Approximately 38 mA
At operation: Approximately 210 mA
Approximately height 145 mm x width 165 mm x depth 44 mm
(5 
3/4″ x 6 1/2″ x 1 3/4″)
Approximately  600 g (1.32 lb.)
0 °C to 40 °C (32 °F to 104 °F), Up to 90 % RH
(Relative Humidity) non condensing
Exposure mount
Flush mount (Optional...

19 

For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Dealer’s name and address
Dealer’s telephone number
Attach your sales receipt here.
LHQT0198
S0405-0 Printed in INDONESIA Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094, U.S.A.
Panasonic Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5, Carolina, Puerto Rico
00985, U.S.A.
Copyright:
•This material is...