Panasonic Sub Monitor Station Video Intercom System Vl Gm001a Installation And Operation Guide

							11
3Install the bottom case to a wall using the wood screws
(4 mm x 35 mm, 3/16″ x 13/8″).
•Before drilling, see page 8 for installation location.

Introduction and Installation 
						

							12
5Attach the wires that connect to the monitor station and sub monitor station to
the terminal. See page 16 for details on how to attach the wires.
•See page 9 for the wire type and distance.
•See the wiring schematic diagram on page 9.
4Attach the power cable to the terminal. See page 16 for details on how to attach
the power cable.
•If you want to use your own power cable, see page 9 for the type and distance.

Button
Power switch
•When the front case is
attached, the power
switch will be pressed and
power will be supplied.
Terminal
(Non polar)
Wire
(Not included)
Introduction and Installation 
						

							13
•Check that there are no scraps from
the board or other debris in the
connector before installing it.
 Remove the front case from the bottom case
Bottom case
Front case
 While pushing the tabs at the top of the front case, pull the top of the front case
forward to disengage the front tabs one by one, and then pull the top of front
case forward to remove it.
 Remove the connector screw, and then remove the connector.
Do not pull the wire
when removing the
connector.
Introduction and Installation
6Remove the sheet covering the connector. Next, after
installing the terminal cover in the bottom case, attach
the connector by tightening the connector screw.
Next, align the lower portion of the bottom case with
the lower portion of the front case and press on the
panel area just above the screen until the tabs lock in
place.Connector screw
Screwdriver + 
						

							14
Introduction and Installation
Arrow mark
DC terminal AC adaptor
8Connect the power cable to the DC terminal, the power cord to the AC adaptor,
then connect the power cord to the AC outlet (100 V – 240 V, 50 Hz / 60 Hz).
•Be sure to connect the power cable to the 2 holes on the left side of the DC
terminal.
•For details on how to attach the power cable, see page 16.
DC terminal AC adaptor Power cord
To AC  outlet
Power cable
9Attach the DC cord to the clamp on the rear of the DC terminal.
• This will help to avoid the DC cord to disconnect from the DC terminal.
DC terminal
DC cord
Clamp
7Take out the AC adaptor and the DC terminal from the case.
•Push the arrow mark on the front case, then release from the rear case.
•Take out the cardboard and wood screws. The wood screws are necessary
when attaching the AC adaptor and the DC terminal to a wall (page 15). 
						

							15
Introduction and Installation
To attach the AC adaptor and the DC terminal to a wall
By placing the AC adaptor and the DC terminal in the case and mounting the case
to the wall, you can protect the AC adaptor and the DC terminal from tampering and
exposure.
1Attach the rear part of the case to a wall using the wood screws (4 mm x 16 mm,3/16″ x 5/8″). Note:
• Disconnect the DC cord from the clamp on the rear of the DC terminal beforehand.
See step 9 on page 14 for details.
• Take out the cardboard and wood screws from the AC case beforehand.
Wood screwsCase
83.5 mm
(
3 
5/16″)
Wall
2Pack the AC adaptor and DC terminal as shown.
Pack the AC adaptor in the rear case.
•Be sure to run the power cord through the power cord hole.
Pack the DC cord in the rear case.
• Be sure to bundle the DC cord so that it will not touch the bottom of the
case.
Pack the DC terminal in the rear case.
•Be sure to run the wires through the wire hole, then under the wire rib.
Wire rib
Wire hole
 DC terminal
Power cord holePower cord
 AC adaptor DC cord
3Attach the front of the case. 
						

							16
To attach the wires
•Strip off of the wire cover so that about 9 mm (
3/8″) of the wire is exposed.
•While pressing on the button with a pointed object such as a screwdriver, insert
the wire into the terminal connector.
•To disconnect a wire, press on the button while pulling out.
Introduction and Installation
Note:
• To open the case again, push the bottom of the front case, then release from the
rear case.
To attach the power cable
•While pressing on the button hard with a pointed object such as a screwdriver,
insert the power cable into the terminal connector.
•To disconnect the power cable, press on the button hard while pulling out.
•To attach an optional power cable, cut off about 12 mm (
1/2″) of the cable cover
(
), then push in firmly until the end of the cable is securely inserted into the
power connection terminal (
). Sub Monitor station
Button
Terminal
connector Button
Terminal
connector
Power cable cross section
Correct Incorrect
DC terminal 
						

							17
Important information:
•Do not use anything containing alcohol, polish powder, powder soap, benzine,
thinner, wax, petroleum, or boiling water. Also do not spray with insecticide, glass
cleaner, or hair spray. This could cause a change in color or quality. Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit
with a slightly damp cloth.
Cleaning
Help 
						

							18
Technical data about this product
General Information
Sub Monitor station
Power supply:
Current consumption:
Dimensions:
Mass (Weight):
Operating environment:
Installation method:
External material:24 V DC
Standby: Approximately 38 mA
At operation: Approximately 210 mA
Approximately height 145 mm x width 165 mm x depth 44 mm
(5 
3/4″ x 6 1/2″ x 1 3/4″)
Approximately  600 g (1.32 lb.)
0 °C to 40 °C (32 °F to 104 °F), Up to 90 % RH
(Relative Humidity) non condensing
Exposure mount
Flush mount (Optional Flush mount unit is required.)
Flame retardant ABS resin (panel: acrylic resin)
Note:
•Design and specifications are subject to change without notice.
•The pictures and illustrations in these instructions may vary slightly from the
actual product.
AC adaptor (Part number: PFAP1014)
Power supply:
Output voltage:
Output current:
Dimensions:
Mass (Weight):
Operating environment:100 V – 240 V 
AC , 50 Hz / 60 Hz
24 V DC
2 A
Approximately height 120 mm x width 60 mm x depth 35 mm
(4
 3/4″ x 2 3/8″ x 1 3/8″)
Approximately 310 g (0.68 lb.)
0 °C to 40 °C (32 °F to 104 °F), Up to 90 % RH
(Relative Humidity) non condensing Note:
•To connect to a chime, make sure the chime is:
– Normal open (Low active)
– Less than 30 V AC (1 A), 24 V DC (1 A) 
						

							19 
						

							For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Dealer’s name and address
Dealer’s telephone number
Attach your sales receipt here.
LHQT0198
S0405-0 Printed in INDONESIA Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094, U.S.A.
Panasonic Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5, Carolina, Puerto Rico
00985, U.S.A.
Copyright:
•This material is copyrighted by Panasonic Communications Co., Ltd., and may be
reproduced for internal use only. All other reproduction, in whole or in part, is
prohibited without the written consent of Panasonic Communications Co., Ltd.
© 2005 Panasonic Communications Co., Ltd. All Rights Reserved.