Panasonic Small Digital Business System 308/616 Installation Instructions

Section 700 
Issue 
1 July 1990 S-DBS Operating Instructions 
Vl .o 
DIALING ALTERNATIVES 
Redial 
The REDIAL key repeats the last number dialed up 
to a maximum of 16 digits.’ A 
maximurn of five speed dialing codes can also be redialed. 
1. Press a line key 
c-3 
. 
3. Press REDIAL key 
4. If the number is still busy, you can press REDIAL key again only ifthe 
system is programmed for Auto-Flash-F&dial. The outside line is 
flashed once automatically and the last number is redialed. 
To check a...

S-DBS Operating Instructions 
Vl .o Section 700 
Issue 1 July 1990 
Save/Repeat Dial 
Redials a previously dialed outside line number. Unlike redial, the number will not 
be lost. even if you dial another number. 
To save a dialed number (During outside line call) 
1. Press AUTO key twice 
2. Press 
* 
NOTE: Saved numbers are erased when a new number is saved. 
To check a saved number: 
1. Press ON/OFF key 
2. Press CONF key 
3. Press AUTO key 
To repeat a dialed number 
1. Press a line key 
2. Press...

Section 700 S-DBS Operating Instructions 
Issue 1 July 1990 Vl .o 
Personal Speed Dial (PSD) 
You can store frequently dialed numbers in a PSD key, thereby, reducing the possi- 
bility of dialing wrong numbers and allowing instant dialing at the touch of a key. 
To store PSD Numbers on a One-Touch key 
1. Press ON/OFF key 
2. Press PROG key 
3. Press One-Touch key (each telephone has 10 One-touch keys). 
4. Dial number 
5. Press HOLD key 
6. Press ON/OFF key 
NOTE: You can also store a number in PSD...

--__ -_ 
S-DBS’Operating Instructions 
Vl .o Section 700 
Issue 1 July 1990 
To access a stored PSD number 
1. Press the line key 
2. Press One-Touch key 
To check a stored PSD number 
1. Press ON/OFF key 
2. Press CONF key 
- ~__--_-.-. - - -_- -.. 
3. Press One-Touch key 
To cancel a stored PSD number 
1. Press ON/OFF key 
2. Press PROG key 
3. Press One-Touch key 
4. Press HOLD key 
34  

Section 700 S-DBS Operating Instructions 
Issue 1 July 1990 Vl .o 
System Speed Dial (SSD) 
You can store frequently dialed numbers in an SSD key allowing instant dialing at the 
touch of a key. Numbers entered in the SSD memory can only be entered fi-om 
extensions 10 and 11. 
To store SSD Numbers 
* 4vailabZe only on extensions 10 and 11~ 
1. Press ON/OFF key 
2. Press PROG key 
3. Press AUTO key 
__..- --- -. - .- ..__~. _ _. 
4. Key in SSD code (00 - 89) 
5. Dial number 
6. Press HOLD key 
7. Press...

S-DBS Operating instructions 
_I- .-______. Section 700 
Issue 1. July 1990 
To access a stored SSD number 
1. Press 
a line key 
2. Press AUTO key 
3. Enter the SSD code (00-89) 
To check an SSD number * uWaiZabZe on all extensions, 
1. 
Press ON/OFF key 
2. Press CONF key 
3. Press AUTO key 
4. Enter SSD code (00 - 89) 
To cancel a stored SSD number 
1. 
Press ON/OFF key 
2. Press PROG key 
3. Press AUTO key 
4. Enter SSD code (00 - 89) 
5. Press HOLD key 
36  

Section 700 S-DBS Operating Instructions 
issue 
1 July 1990 Vl .o 
Assigning Two SSD Codes to a Single One-Touch Key 
If you assign a frequently used access code to one SSD code and a telephone number 
to a second SSD code, you can dial the telephone number by entering the first SSD 
code followed by the second SSD code. However, both SSD codes can be programmed 
on a One-Touch key. 
1. Press ON/OFF key 
2. Press PROG key 
3. Press the One-Touch key 
- ---.._ 
4: -- -- Press AUTO key -- - 
5. Key in the...

S-DBS Operating Instructions Section 700 
----w-;3----------~ .-.... .--_._-.-._. Issue. 1 July 1990 
DTMF Signal Conversion 
You can change from pulse to tone dialing, even on a rotary telephone. However, once 
you make the change to tone you cannot change back to pulse on the same call. Also, 
you cannot send tone signals either during a call or while you are dialing. 
1. Press line key 
2. Press 
* or # key 
3. Replacing the receiver returns the line to pulse. 
NOTE: You can program the * or # key in...

Section 700 
issue 1 July 1990 
ACCOUNT CODES/SMDR 
Account Code Station Message Detail Recorder (SMDR) 
When a serial interface printer is connected to S-DBS, information such as call dates 
and times, numbers called, outside line numbers used, etcetera, can be printed for 
each account by entering its code number. 
Separate account numbers 
can be assigned to different clients for preparing bills. 
Each account code 
can be a maximum of ten digits. Enter the code either before 
dialing or during the...

S-DBS Operating Instructions Section 700 
Vl .o Issue 1 July 1990 
To enter an Account Code during an outside call 
1.2essAu~o~ey~ -----.-. -. -- -...- --.----_______ _ _ .._ 
2. 
Press # 
3. Key in the account code (up to 10 digits). 
4. 
Press # 
NOTE: Not available on SLT. 
40