Panasonic Sdr S25 Operating Instructions Manual

							91LSQT1562
It is possible that the system cannot complete writing of a file normally when, for example, power is 
turned off for some reason during recording or editing.
If faulty management information is found when an SD card is accessed, the following message may 
appear. Be sure to follow the messages. (Repairing may take time depending on the error.)
≥When you repair the data, use a battery with sufficient battery power or the AC adaptor. Even if the 
power is turned off without repairing the data,  you can repair the data when you turn the power on 
again.
≥ Depending on the condition of the data, it may not be possible to completely repair the data.
≥ Do not repair an SD card that has been recorded on  another device. This may cause the loss of data 
or the card.
About recovery
NOW REPAIRING DATA. DO NOT REMOVE CARD.
SDR-S25P-LSQT1562_mst.book  91 ページ  ２００９年２月１２日　木曜日　午後５時４８分 
						

							92LSQT1562
Others
Helpful hints
1
Functions that cannot be 
used simultaneously
Some functions in this unit are disabled or cannot be selected due to the unit’s specifications. 
The table below shows examples of functions restricted by various conditions.
FunctionsConditions which
disable the functions
Digital zoom ≥In Picture Recording mode
Intelligent auto mode ≥When the MagicPix function is used
Fade ≥In Picture Recording mode
≥ When PRE-REC is used
MagicPix ≥While recording (Cannot set or cancel)
≥ In Picture Recording mode
≥ When PRE-REC is used (Cannot set or cancel)
Backlight compensation ≥When the MagicPix function is used
≥ When the iris/gain is set
Soft skin mode (Set and cancel) ≥While recording
≥ When PRE-REC is used
Help mode
Face detection ≥When the MagicPix function is used
Scene mode ≥When the MagicPix function is used
Change of white balance ≥When Digital Zoom is used
≥ When the MagicPix function is used
Adjusting the shutter speed, iris/gain ≥When the MagicPix function is used
≥ When Scene Mode is used
Guideline ≥When Face Detection is used
SDR-S25P-LSQT1562_mst.book  92 ページ  ２００９年２月１２日　木曜日　午後５時４８分 
						

							93LSQT1562
Others
Helpful hints
2
Troubleshooting
ProblemCheck points
This unit cannot be 
turned on.
This unit does not stay 
on long enough.
Battery runs down 
quickly. ≥
Charge the battery using the AC adaptor. ( l17)
≥ Make sure the LCD monitor is opened.
≥ The battery is affected by ambient temperature. In cold 
places, the battery usi ng time becomes shorter.
≥ The battery has a limited life. If the operating time is still too 
short even after the battery is  fully charged, the battery has 
worn out and needs to be replaced.
This unit is turned off 
automatically. ≥
If you do not use the unit for approximately 5 minutes, the 
power is automatically turned off  to conserve battery life. To 
resume recording, turn the power back on.
The power will not turn off automatically when the economy 
function ( l26) is set to [OFF].
This unit cannot be 
operated though it is 
turned on.
This unit does not 
operate normally. ≥
The unit cannot be operated unless you open the LCD 
monitor.
≥ Turn on the power again. If normal conditions are not 
restored yet, remove the battery or AC adaptor, wait about 
1 minute and then reconnect the battery or AC adaptor. 
Then about 1 minute later, turn on the power again. 
(Conducting the above operation while the SD card is being 
accessed may damage the data on the SD card.)
SDR-S25P-LSQT1562_mst.book  93 ページ  ２００９年２月１２日　木曜日　午後５時４８分 
						

							94LSQT1562
ProblemCheck points
A clicking sound is heard 
when the power is turned 
off. ≥
This is the sound of the lens moving and is not a 
malfunction.
The screen has changed 
suddenly.
(Demo mode is on) ≥
If you set [DEMO MODE] to [ON] without inserting an SD 
card in video recording mode or picture recording mode, 
the unit is automatically set to the demonstration mode for 
introducing its functions. Normally this should be set to 
[OFF]. ( l27)
A function indication 
such as the remaining 
time indication or the 
elapsed time indication is 
not shown. ≥
If you set [SETUP]  > [DISPLAY] >  [OFF], indications 
other than warnings and date are not displayed.
Recording does not start 
although power is 
supplied to this unit. ≥
No recording is possible while the SD card’s write protect 
switch is set to LOCK. ( l20)
≥ If the SD card has no more available memory, free up some 
memory by deleting unnecessary scenes ( l58) or use a 
new SD card.
≥ Is the unit set to the video recording mode or picture 
recording mode?
≥ If the SD card slot cover is open, this unit may not operate 
normally. Close the card slot cover.
SDR-S25P-LSQT1562_mst.book  94 ページ  ２００９年２月１２日　木曜日　午後５時４８分 
						

							95LSQT1562
ProblemCheck points
Recording stops 
suddenly during motion 
picture recording on an 
SD card. ≥
Use an SD card that can be used for motion picture 
recording. ( l21)
≥ When using an SD card on which data has been written 
many times and the data writ ing speed has reduced, the 
recording may suddenly stop during motion picture 
recording. Back up the data on the SD card to a PC, etc. 
and then format the SD card. ( l63)
Auto focus function does 
not work. ≥
Press MANUAL AF/MF button to erase the MF icon, or 
press iA button.
≥ There are some recording subjects and surroundings for 
which the auto focus does not operate correctly. (l 101) If 
so, use the manual focus mode to adjust the focus. ( l50)
“ENVIRONMENT TOO 
DARK, OR LENS COVER 
CLOSED.” is displayed. ≥
Open the lens cover before turning the unit on.
≥ This message may appear if you try to record in extremely 
dark places.
Sound is not played back 
from the built-in speaker 
of this unit. ≥
During playback, move the volume lever to display the 
volume indication and adjust it. ( l54)
Although this unit is 
correctly connected to a 
TV, playback images 
cannot be seen.
The playback images are 
squeezed horizontally. ≥
Please read the operating instructions of your TV and 
select the video input that this unit is connected to.
≥ Change the setting to match the aspect ratio of the TV. 
(l 65)
Scenes or files cannot be 
deleted or edited. ≥
Locked scenes or files cannot be deleted. Release the lock 
setting. ( l60, 61)
≥ It may not be possible to delete scenes that are displayed 
as [ ] on the thumbnail display. If the scenes are 
unnecessary, format the SD card to erase the data. ( l63) 
Please be aware that if the SD card is formatted then all the 
data recorded on the SD card will be erased.
≥ If the SD card’s write protect switch is set to LOCK, then 
deletion and editing are disabled. ( l20)
The images on the SD 
card do not look normal. ≥
The data may be destroyed. It may have been destroyed by 
static or electromagnetic waves. Store important data on a 
PC or other products as well.
SDR-S25P-LSQT1562_mst.book  95 ページ  ２００９年２月１２日　木曜日　午後５時４８分 
						

							96LSQT1562
Even if an SD card is 
formatted, it cannot be 
used.≥
Either this unit or the SD card may be damaged. Please 
contact consumer support ( l111 ).
≥ Use an SD card from 8 MB to 32 GB with this unit. ( l20)
The indication 
disappears.
The screen is frozen.
No operation can be 
performed. ≥
No operation can be performed on this unit when it is 
connected to a PC.
≥ Turn off the power to this unit. If the power cannot be turned 
off, remove the battery or AC adaptor and then reconnect it. 
Turn on the power again. If normal operation is still not 
restored, detach the power  connected, and contact 
consumer support. ( l111 )
“ERROR OCCURRED. 
PLEASE TURN UNIT OFF, 
THEN TURN ON AGAIN.” 
is displayed. ≥
The unit has automatically detected an error. Restart the 
unit by turning off and on the power.
≥ The power will be turned off in about 1 minute if the power 
is not turned off and on.
≥ Repair is needed if it is repeatedly displayed even if it is 
restarted. Detach the power connected, and contact 
consumer support. ( l111) Do not attempt to repair the unit 
by yourself.
When the SD card is 
inserted in this unit, it is 
not recognized. ≥
Use this unit to format SD cards. Please be aware that if an 
SD card is formatted, then all the data recorded on the card 
will be erased. ( l63)
When the SD card is 
inserted in another 
device, it is not 
recognized. ≥
Check that the device is compatible with the capacity or 
type of SD card (SD Memory Card/SDHC Memory Card) 
that you inserted. Refer to the operating instructions of the 
device for details.
ProblemCheck points
SDR-S25P-LSQT1562_mst.book  96 ページ  ２００９年２月１２日　木曜日　午後５時４８分 
						

							97LSQT1562
With other products
With a PC
ProblemCheck points
The sound does not play 
back properly when a 
DVD disc that has been 
copied using the DVD 
burner is played back. ≥
When the scenes recorded on an SD card by setting 
[AUDIO REC] to [MPEG] are copied to a DVD disc using 
the DVD burner and then played back with any other 
devices, sound may not  play back properly.
In this case, record scenes by setting [AUDIO REC] to 
[DOLBY] and then copy to the disc. Or use the software 
supplied with this unit to copy the scenes.
ProblemCheck points
When connected by the 
USB cable, this unit is not 
detected by the PC. ≥
Close the menu screen before connecting the USB cable.
≥ Select another USB terminal on the PC.
≥ Check the operating environment. ( l77)
≥ Disconnect the USB cable, turn the unit off then on and 
then reconnect the USB cable.
When the USB cable is 
disconnected, an error 
message will appear on 
the PC. ≥
To disconnect the USB cable safely, double-click the   
( ) icon in the task tray and follow the instructions on the 
screen.
It takes a long time to 
create a DVD. ≥
Creating a DVD may take some time even if the size of the 
motion picture files are small.
The DVD player cannot 
play back the discs I have 
created using VideoCam 
Suite. ≥
To playback a DVD disc created using VideoCam Suite, the 
player must support playback of that DVD disc. (Refer to 
the operating instructions of the player.)
SDR-S25P-LSQT1562_mst.book  97 ページ  ２００９年２月１２日　木曜日　午後５時４８分 
						

							98LSQT1562
Others
Cautions for use
≥The unit and SD card become warm after long 
operation, but this is not a malfunction.
Keep the SD Video Camera as far away as 
possible from electromagnetic equipment 
(such as microwave ovens, TVs, video games 
etc.).
≥ If you use the SD Video Camera on top of or 
near a TV, the pictures and sound on the SD 
Video Camera may be disrupted by 
electromagnetic wave radiation.
≥ Do not use the SD Video Camera near cell 
phones because doing so may result in noise 
adversely affecting the pictures and sound.
≥ Recorded data may be damaged, or pictures 
may be distorted, by strong magnetic fields 
created by speakers or large motors.
≥ Electromagnetic wave radiation generated by 
microprocessors may adversely affect the SD 
Video Camera, disturbing the pictures and 
sound.
≥ If the SD Video Camera is adversely affected 
by electromagnetic equipment and stops 
functioning properly, turn the SD Video 
Camera off and remove the battery or 
disconnect AC adaptor. Then reinsert the 
battery or reconnect AC adaptor and turn the 
SD Video Camera on.
Do not use the SD Video Camera near radio 
transmitters or high-voltage lines.
≥ If you record near radio transmitters or 
high-voltage lines, the recorded pictures and 
sound may be adversely affected.
Make sure to use the supplied cords and 
cables. If you use optional accessories, use 
the cords and the cables supplied with them.
Do not extend the cords and the cables. Do not spray insecticides or volatile 
chemicals onto the unit.
≥
If the unit is sprayed with such chemicals, its 
body may be marred and the surface finish 
may peel off.
≥ Do not leave rubber or plastic products in 
contact with the unit for a long time.
When you use the unit in a sandy or dusty 
place such as a beach, do not let sand or fine 
dust get into the body and terminals of the 
unit.
Also, keep the unit away from sea water.
≥ Sand or dust may damage the unit. (Care 
should be taken when inserting and removing 
an SD card.)
≥ If sea water splashes onto the unit, wipe off the 
water with a well wrung cloth. Then wipe the 
unit again with a dry cloth.
When carrying the unit, do not drop or bump 
it.
≥ A strong impact can break the unit’s casing, 
causing it to malfunction.
Cleaning
≥ Before cleaning, detach the battery or pull the 
AC cable from the AC outlet, and then wipe the 
unit with a soft, dry cloth.
≥ If the unit is very dirty, dip a cloth in water and 
squeeze firmly, and then wipe the unit with the 
damp cloth. Next, dry the unit with a dry cloth.
≥ Use of benzine, paint thinner, alcohol, or 
dishwashing liquid may alter the camera body 
or peel the surface finish. Do not use these 
solvents.
≥ When using a chemical dust cloth, follow the 
instructions that came with the cloth.
Do not use the unit for surveillance purposes 
or other business uses.
≥ This unit was designed for consumer 
intermittent use. It was not intended for 
continuous use, or for any industrial or 
commercial application resulting in prolonged 
use.
≥ In certain situations, continuous use could 
cause the unit to overheat and cause a 
malfunction. Such use is strongly discouraged.
About this unit
SDR-S25P-LSQT1562_mst.book  98 ページ  ２００９年２月１２日　木曜日　午後５時４８分 
						

							99LSQT1562
When you are not going to use the unit for an 
extended time
≥When storing the unit in a cupboard or cabinet, 
it is recommended that you place a desiccant 
(silica gel) in with it.
The battery used in this unit is a rechargeable 
lithium-ion battery. It is susceptible to humidity 
and temperature and the effect increases the 
more the temperature rises or falls. In cold areas, 
the full charge indication may not appear or the 
low battery indication may appear for about 
5 minutes after starting use. At high 
temperatures, the protection function may be 
triggered, making it impossible to use the unit.
Be sure to detach the battery after use.
≥ If the battery is left inserted, a minute amount 
of current continues to flow even if the unit’s 
power is off. Keeping the unit in this state may 
result in over discharge of the battery. This 
may result in you not being able to use the 
battery even after it is charged.
≥ The battery should be stored in the vinyl bag 
so metal does not come into contact with the 
terminals.
≥ The battery should be stored in a cool place 
free from humidity, with as constant 
temperature as possible. (Recommended 
temperature: 15 °C to 25 °C (59 °F to 77 °F), 
Recommended humidity: 40% to 60%)
≥ Extremely high temperatures or low 
temperatures will shorten the life of the battery.
≥ If the battery is kept in high-temperature, high-
humidity, or oily-smoky places, the terminals 
may rust and cause malfunctions.
≥ To store the battery for a long period of time, 
we recommend you charge it once every year 
and store it again after you have completely 
used up the charged capacity.
≥ Dust and other matter attached to the battery 
terminals should be removed.
Prepare spare batteries when going out for 
recording.
≥ Prepare enough batteries to last 3 to 4 times 
the period you are planning to record.
≥ Cold weather, such as when skiing, can 
shorten the recording period. If you drop the battery accidentally, check to 
see if the terminals are damaged.
≥
Inserting a battery with damaged terminals can 
damage the unit.
Do not throw old battery into fire.
≥ Heating a battery or throwing it into a fire may 
result in an explosion.
If the operating time is very short even after 
the battery has been recharged, the battery 
has worn out. Please purchase a new battery.
About the battery
SDR-S25P-LSQT1562_mst.book  99 ページ  ２００９年２月１２日　木曜日　午後５時４８分 
						

							100LSQT1562
≥If the temperature of the battery is extremely 
high or extremely low, charging may take time 
or the battery may not be charged.
≥ If you use the AC adaptor near a radio, radio 
reception may be disturbed. Keep the AC 
adaptor 1 m (3.3 feet) or more away from the 
radio.
≥ When using the AC adaptor, it may generate 
whirring sounds. However, this is normal.
≥ After use, be sure to disconnect the AC 
adaptor. (If it is left connected, a minute 
amount of current is consumed.)
≥ Always keep the electrodes of the AC adaptor 
and battery clean.
≥ When the LCD monitor gets dirty, wipe it with a 
dry soft cloth.
≥ In a place with drastic temperature changes, 
condensation may form on the LCD monitor. 
Wipe it with a soft dry cloth.
≥ When the unit has become very cold, for 
example due to storage in a cold area, its LCD 
monitor will be slightly darker than usual 
immediately after the power is turned on. The 
normal brightness will be restored when the 
unit’s internal temperature rises.
If condensation forms on the unit, the lens will 
cloud up and the unit may not work properly. 
Make every effort to ensure that condensation 
does not form. If it does form, take the actions 
described below.
Causes of condensation
Condensation takes place when the ambient 
temperature or humidity is changed as 
follows.
≥ When this unit is brought inside from the cold 
(e.g. a ski slope) to a warm room.
≥ When this unit is moved from an 
air-conditioned car to outside.
≥ When a cold room has been warmed up 
quickly.
≥ When cool wind from an air conditioner is 
directly blown onto this unit.
≥ After summer afternoon showers of rain.
≥ When this unit is in a very humid place where 
the air is thick with steam. (e.g. a heated 
swimming pool)
Helpful hint
If, for example, you have used this unit for 
recording on a ski slope and are taking it into a 
heated room, place the unit inside a plastic bag, 
remove as much of the air from inside the bag as 
possible, then seal the bag. Leave the unit for 
about an hour in the room so the temperature of 
the unit is close to the ambient temperature of 
the room, then use it.About the AC adaptor
LCD monitor
Extremely high precision technology is 
employed to produce the LCD Monitor screen 
featuring a total of approximately 123,000 
pixels. The result is more than 99.99% 
effective pixels with a mere 0.01% of the 
pixels inactive or always lit. However, this is 
not a malfunction and does not affect the 
recorded picture.
About condensation
SDR-S25P-LSQT1562_mst.book  100 ページ  ２００９年２月１２日　木曜日　午後５時４８分