Panasonic Pv Gs33 Operating Instructions Manual

							Recording Mode
-31-
Deleting All the Captured Multi-Pictures
While 9 multi-pictures are displayed, press the 
[MULTI] Button.
≥If [MANUAL] has been selected, press the 
[MULTI] Button after 9 pictures are displayed.
To Display the Multi-Pictures Again
Press the [MULTI] Button for 1 second or longer.
To Delete Multi-Pictures One by One(When pictures were captured in [MANUAL])
When the [MULTI] Button is pressed for 1 second 
or longer while the still pictures are displayed, the 
pictures captured last are deleted continuously.
≥After still pictures are deleted one by one, they 
cannot be displayed again.
≥For other notes concerning this item, see 
-50-.
ªPicture-in-Picture Mode
You can display a sub-screen (still picture) inside 
the screen.
1Set [TAPE RECORDING MENU] >> 
[DIGITAL] >> [EFFECT1] >> [P-IN-P].
2Aim the Camcorder at the scene you want 
to capture and press the [P-IN-P] Button (6) 
to insert a small still picture.
≥A small still picture is displayed in a normal 
picture.
≥If the [P-IN-P] Button is pressed again, the 
small still picture is cleared.
≥For other notes concerning this item, see 
-50-.
MENU
STILL
ENTERFA D Ei s
(14)
MULTI/
P-IN-P
(6)
ªWipe Mode and Mix ModeWipe Mode:
Like drawing a curtain, the still picture of the last 
recorded scene gradually changes to the moving 
image of a new scene.
Mix Mode:
While the moving image of a new scene fades in, 
the still image of the last recorded scene 
gradually fades out.
1Set [TAPE RECORDING MENU] >> 
[DIGITAL] >> [EFFECT1] >> [WIPE] or [MIX].
≥The [WIPE] or [MIX] Indication appears.
2Press the Recording Start/Stop Button (41) 
to start recording.
3Press the Recording Start/Stop Button (41) 
to pause the recording.
≥The last scene is stored in memory. The 
[WIPE] or [MIX] Indication changes to [B] 
or [C].
4Press the Recording Start/Stop Button (41) 
to restart the recording.
≥The last image of the previous scene 
gradually changes to the new scene.
≥For other notes concerning this item, see 
-50-.
WIPEWIPE
WIPE
MIX
MIX
MIX
MENU
STILL
ENTERFA D Ei s
(14)
(41)
PV-GS33PP_Eng.book  31 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Playback Mode
-32-
Playback Mode
Playing Back a Tape
The recorded scene can be played back 
immediately after the recording.
1Set the [OFF/ON] Switch (42) to [ON].
≥The [POWER] Lamp (43) lights up.
2Set the Mode Dial (39) to Tape Playback 
Mode.
3Press the [6] Button (13) to rewind the 
tape.
≥Rewind the tape to the point where you want 
to start playback.
≥When the tape reaches the beginning, 
rewinding stops automatically.
4Press the [1] Button (11) to start playback.
≥The [!] Indication appears.
≥If a cassette recorded with a copyright 
protection signal is played back, the picture is 
distorted by mosaic-like patterns.
To Stop PlaybackPress the [∫] Button (12).
ONOFF
POWER
(42)
(43)
(39)
STILL
ENTERFA D Ei s(13)
STILL
ENTERFA D Ei s
(11)
(12)STILL
ENTERFA D Ei s
ªAdjusting the Sound VolumeTo adjust the volume, push the [sVOL/JOGr] 
Lever (36) to display the [VOLUME] Indication. 
Push the [sVOL/JOGr] Lever towards [T] to 
increase the volume or push the [sVOL/JOGr] 
Lever towards [W] to decrease the volume. The 
[VOLUME] Indication goes off after the 
adjustment is finished.
To adjust the volume with the Remote Controller, 
press the [T] or [W] Button to display the 
[VOLUME] Indication. Press the [T] Button to 
increase the volume or press the [W] Button to 
decrease the volume. The [VOLUME] Indication 
goes off after the adjustment is finished.
≥The sound volume cannot be adjusted using the 
Remote Controller in Playback Zoom Mode. 
(
-34-)
≥For other notes concerning this item, see 
-50-.
Finding a Scene You Want to Play 
Back
ªCue/Review Playback
If the [5] Button (10) or [6] Button (13) is 
pressed during Playback, it turns to Cue Playback 
A or Review Playback B.
≥If the Button is held continuously, it turns to Cue 
Playback or Review Playback until you release 
it.
VOL/JOG
WT(36)
STILL
ENTERFA D Ei s
(13)         (10)
AB
PV-GS33PP_Eng.book  32 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Playback Mode
-33-
ªVariable Speed Search FunctionThe speed of Cue Playback or Review Playback 
can be varied.
1During playback, press the [1] Button (11).
≥The [1k!] Indication appears.
2Push the [W/T] Lever (36) to select a desired 
search speed.
The following 6 playback speeds are available for 
the Variable Speed Search Function in both the 
fast-forwarding and rewinding directions: 
1/5k (slow playback in SP Mode only), 1/3k 
(slow playback in LP Mode only), 1k, 2k, 5k, 
10k and 20k.
≥This function works by pressing the 
[VAR. SEARCH] and cursor buttons ([π,∫]) on 
the Remote Controller. (
-12-)
To Resume Normal Playback
Press the [1] Button (11).
≥During Cue or Review Playback, fast-moving 
images may show mosaic-like patterns.
≥The sound is muted during search.
Slow Motion Playback
This Camcorder can play back at a slow speed.
1Press the [1] Button (72).2Press the [E] Button or [D] Button (57) on 
the Remote Controller.
≥The [}] or [~] Indication appears.
≥When the [E] Button is pressed, Slow Motion 
Playback proceeds in the reverse direction. 
When the [D] Button is pressed, Slow Motion 
Playback proceeds in the forward direction.
STILL
ENTERFA D Ei s
(11)
VOL/JOG
WT(36)
INDEX INDEX
SELECT
STOPKL∫
V/REW
STILL ADVWsPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP.B. ZOOM
(72)
(57)
(57)
}
Scenes recorded in the SP Mode are played back 
at approximately 1/5th of the normal speed.
Scenes recorded in the LP Mode are played back 
at approximately 1/3rd of the normal speed.
To Resume Normal PlaybackPress the [1] Button (72).
≥If the Camcorder is left in the Slow Motion 
Playback Mode for more than 10 minutes, the 
Camcorder switches to the Stop Mode to 
protect the video heads from excessive wear 
and tear.
Still Playback/Still Advance 
Playback
This Camcorder is capable of still picture 
playback and frame-advance playback.
1Press the [1] Button (72).2Press the [;] Button (69).
≥The playback image stops in the Still 
Playback Mode.
3Press the [E] Button or [D] Button (57) on 
the Remote Controller.
≥With each press of the [E] Button, still 
pictures advance in the reverse direction. 
With each press of the [D] Button, still 
pictures advances in the forward direction. If 
one of the buttons continues to be pressed, 
still pictures advance continuously 1 frame at 
a time until the button is released.
To Resume Normal Playback
Press the [1] Button (72).
ªPlayback with Zoom LeverBy pushing the [W/T] Lever (36) of the 
Camcorder in the Still Playback Mode, still 
pictures can be advanced one frame at a time in 
the forward or backward direction. If you keep 
pushing the Lever, still pictures advance 
continuously.
≥If the Camcorder is left in the Still Playback 
Mode for more than 5 minutes, the Camcorder 
switches to the Stop Mode to protect the video 
heads from excessive wear and tear.
INDEX INDEX
SELECT
STOPKL∫
V/REW
STILL ADVWsPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP.B. ZOOM
(72)
(69)
(57)(57)
VOL/JOG
WT(36)
PV-GS33PP_Eng.book  33 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Playback Mode
-34-
Index Search Functions
To facilitate searching for desired scenes, this 
Camcorder automatically records index signals 
during recording, as explained in the following.
Photoshot Index Signal
These signals are automatically recorded 
whenever still pictures are taken in Photoshot 
Mode (
-22-). Photoshot Index Signals are not 
recorded on still pictures recorded in Continuous 
Photoshot Mode.
Scene Index Signal
Scene Index Signals are automatically recorded 
when you start recording after inserting a 
Cassette.
≥If [SCENE INDEX] of [RECORDING] Sub-Menu 
on the [TAPE RECORDING MENU] is set to 
[2HOUR], an index signal is recorded when 
recording is restarted after an elapse of 2 hours 
or longer. If it is set to [DAY], an index signal is 
recorded when recording is restarted after the 
date has changed since the last recording. 
(While the index signal is being recorded, the 
[INDEX] Indication flashes for a few seconds.)
≥If the Camcorder is switched from the Tape 
Playback Mode to Tape Recording Mode or if 
the date and time is set before the start of 
recording, the index signal is not recorded.
ªPhotoshot Index Search
1Set [TAPE PLAYBACK MENU] >> 
[PLAYBACK] >> [SEARCH] >> [PHOTO].
2Press the [9] Button or [:] Button (58) 
on the Remote Controller.
≥With each press of the corresponding button, 
still pictures recorded in Photoshot Mode are 
searched.
≥Sounds are played back for approximately 
4 seconds.
INDEX
MENU
STILL
ENTERFA D Ei s
(14)
INDEX INDEX
SELECT
STOPKL∫
V/REW
STILL ADVWsVPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP.B. ZOOM(58) (58)
ªScene Index Search
1Set [TAPE PLAYBACK MENU] >> 
[PLAYBACK] >> [SEARCH] >> [SCENE].
2Press the [9] Button or [:] Button (58) 
on the Remote Controller.
≥When the corresponding button is pressed 
once, the [S 1] Indication appears, and 
searching for the subsequent scene marked 
with an index signal starts. Each time the button 
is pressed after the start of Scene Index 
Search, the indication changes, from [S 2] to 
[S 9], and the beginning of the scene 
corresponding to the selected number will be 
searched.
≥Up to 9 scene numbers can be selected.
Continuous Index SearchIf the [9] Button or the [:] Button (58) is 
pressed for 2 seconds or longer, search can be 
continued at several-second intervals. (To cancel, 
press the [1] Button 
(72) or the [∫] Button (70).)
≥For other notes concerning this item, see 
-50-.
Playback Zoom Function
A part of the image can be enlarged up to 
10 times during playback.
1During playback, press the [P.B. ZOOM] 
Button (74) on the Remote Controller.
≥The center of the image is enlarged to 
approximately 2 times.
S   1
INDEX INDEX
SELECT
STOPKL∫
V/REW
STILL ADVWsVPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP.B. ZOOM
(72)
(70)
INDEX INDEX
SELECT
STORESTOP
KL∫
OFF/ON
P. B . D I G I TA L
ENTER
VA R .
SEARCHMENU
P.B. ZOOM(74)
(56)
(56)
ZOOM 2t 
PV-GS33PP_Eng.book  34 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Playback Mode
-35-
To Change the Zoom Magnification
2Change the magnification by pressing the 
[W] Button or [T] Button (62) on the Remote 
Controller.
To Change the Enlarging Area of an Image3Press the Arrow Button (π, ∑, ∏, ∫) (56) 
on the Remote Controller that points to the 
area you want to enlarge.
To Cancel the Playback Zoom FunctionPress the [P.B. ZOOM] Button (74) on the 
Remote Controller.
≥For other notes concerning this item, see 
-50-.
Playback Digital Effect Functions
During playback, special digital effects can be 
added to the recorded pictures. The same effects 
as those of Digital Effects 1 and 2, which are 
used during recording, are obtained.
1Press the [1] Button (72).
2Press the [SELECT] Button (59) on the 
Remote Controller to select a desired digital 
effect.
≥When the [SELECT] Button is pressed 
repeatedly, the digital effect selection 
changes.
≥The same setting can be done using 
[EFFECT SEL] Sub-Menu on the 
[TAPE PLAYBACK MENU].
To suspend Playback Digital Effect 
Temporarily
Press the [OFF/ON] Button (61) to suspend or 
restart the digital effect. When the digital effect is 
paused temporarily, the selected effect’s 
indication flashes.
ZOOM OSDDISPLAY
V/REWDATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAYFF/
W61 5
(62)
INDEX INDEX
SC
STOPKL∫
V/REW
STILL ADVWsVPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP. B .  Z O O M
(72)
SELECT
STORE
OFF/ON
P.B.DIGITAL
ENTER
VAR.
SEARCHMENU(59)
(61)
To Cancel the Digital Effect
Press the [SELECT] Button (59) on the Remote 
Controller and clear the digital effect indication.
ªWipe Mode and Mix Mode
1Press the [1] Button (72).
2Press the [SELECT] Button (59) on the 
Remote Controller and select [WIPE] or 
[MIX].
3Press the [STORE] Button (60) at the 
moment you want to save as a still picture.
≥The [B] or [C] Indication appears, and 
the image is saved.
4Press the [OFF/ON] Button (61) in the scene 
in which you want to use the Wipe or Mix 
effect.
≥The scene changes as a result of the Wipe or 
Mix effect.
≥The Wipe Function and Mix Function can only 
be accessed by using the Remote Controller 
during playback.
≥If the [OFF/ON] Button 
(61) is pressed while 
Wipe or Mix is carried out, the effect will stop 
temporarily at that point. Pressing the [OFF/ON] 
Button 
(61) again will bring back the effect.
≥For other notes concerning this item, see 
-50-.
INDEX INDEX
SC
STOPKL∫
V/REW
STILL ADVWsVPLAY
PAU S E
FF/W
STILL ADV61 5
;EDP. B .  Z O O M
(72)
SELECT
STORE
KL∫
OFF/ON
P. B . D I G I TA L
ENTER
VAR.
SEARCHMENU(59)
(60)
(61)
PV-GS33PP_Eng.book  35 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Playback Mode
-36-
Playing Back on Your TV
By connecting your Camcorder with your TV, the 
recorded scenes can be viewed on your TV 
screen.
≥Before connecting them, turn off the power of 
both the Camcorder and TV.
1Connect the [A/V OUT] Jack of the 
Camcorder and the Video and Audio Input 
Jacks of the TV.
≥Connect to the TV with the AV Cable 1. If the 
TV has an S-Video Jack, connect the S-Video 
Cable 2, too.
≥When plugging the pin plug of the AV cable 
into the [A/V OUT] Jack, plug it in as far as it 
goes.
To Make the Indications Appear on the TV 
Screen
Press the [OSD] Button (51) on the Remote 
Controller.
≥For other notes concerning this item, see 
-50-. 
1 2
[VIDEO IN]
[AUDIO IN] [S-VIDEO IN]
S-VIDEO
OUT
A/V OUT 
PHONES REMOTE/MIC
(PLUG IN POWER)
DV
ZOOM
OSD
DISPLAY
DATE/
TIME
RESET
TITLE
PHOTO
SHOTSTART/
STOP(51)
PV-GS33PP_Eng.book  36 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Editing Mode
-37-
Editing Mode
Audio Dubbing
You can add music or narration to the recorded 
Cassette.
≥If the tape recorded in the [16bit] Mode is 
dubbed with the Audio Dubbing function, the 
original sound is erased. (If you wish to 
preserve the original sound, use the [12bit] 
Mode when recording.)
≥Audio Dubbing cannot be performed on a 
recording made in LP Mode. (
-20-)1Press the [;] Button (69) on the Remote 
Controller where you want to add new 
sound.
2Press the [A.DUB] Button (55) on the 
Remote Controller.
3To start Audio Dubbing, press the [;] 
Button (69) on the Remote Controller.
To Cancel Audio Dubbing
Press the [;] Button (69) on the Remote 
Controller.
The Camcorder is in the Still Playback Mode 
again.
To Play Back the Sound Recorded by 12bit 
Audio Dubbing
Set [TAPE PLAYBACK MENU] >> [PLAYBACK] 
>> [12bit AUDIO] >> [ST2] or [MIX].
ST1: It plays back only the original sound.
ST2: It plays back only the sound added by Audio 
Dubbing.
MIX: It plays back both the original sound and the 
sound added by Audio Dubbing 
simultaneously.
To Dub Audio While Listening to a 
Pre-recorded Sound
When pausing the audio dubbing, set the 
[12bit AUDIO] on the [PLAYBACK] Sub-Menu to 
[ST2] and you can check the pre-recorded sound.
Use headphones to listen to the pre-recorded 
sound while dubbing the audio.
≥For other notes concerning this item, see 
-50-.
INDEX INDEX
SELECT
STOPKL∫
V/REW
STILL ADV
T
WsVOLr¥REC MULTI/
P-IN-PA.DUB
PLAY
PAUSE
FF/W
STILL ADV61 5
;EDP.B. ZOOM
(55)
(69)
Copying on an S-VHS (or a VHS) 
Cassette
(Dubbing)
After connecting the Camcorder and the VCR 
as illustrated, start the following procedures.
1 AV Cable
2 S-Video Cable
≥Be sure to press the [OSD] Button (
-12-) on the 
Remote Controller prior to copying so that no 
indications are visible. Otherwise, the displayed 
tape counter and function indications are also 
copied.
Camcorder:
1Insert the recorded Cassette.
VCR:
2Insert an unrecorded Cassette with an 
erasure prevention tab.
≥If various setups (such as external input, tape 
speed, etc.) are required, please refer to the 
operating instructions of your VCR.
Camcorder:
3Press the [1] Button (11) to start playback.
VCR:
4Start recording.5Press the Pause or Stop Button to stop 
recording.
Camcorder:
6Press the [∫] Button (12) to stop playback.
1 2
[VIDEO IN]
[AUDIO IN] [S-VIDEO IN]
S-VIDEO
OUT
A/V OUT 
PHONES REMOTE/MIC
(PLUG IN POWER)
DV
PV-GS33PP_Eng.book  37 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Editing Mode
-38-
Using the DV Cable for Recording
(Digital Dubbing)
By connecting this Camcorder with other digital 
video equipment (such as another Camcorder of 
the same format/model) that has a DV 
input/output terminal, and using a 4-pin to 4-pin 
DV Interface cable PV-DDC9 (optional) 1, high 
quality images and sounds can be dubbed in the 
digital mode.
Player/Recorder:
1Insert the Cassette and set to Tape 
Playback Mode.
Player:
2Press the [1] Button (72) to start playback.
Recorder:
3While pressing the [¥REC] Button (54), 
press the [1] Button (72).
Or while pressing the [REC] Button (7), 
press the [BACK LIGHT] Button (8) on the 
Camcorder.
≥Recording starts.
To Stop DubbingPress the [;] Button (69) or the [∫] Button (70).
≥For other notes concerning this item, see 
-51-.
CAUTION:
Unauthorized exchanging and/or copying of 
copyrighted recordings may be copyright 
infringement.
1
DV
INDEX INDEXSTOPKL∫
V/REW
STILL ADV
T
WsVOLr¥REC MULTI/
P-IN-PA.DUB
PLAY
PAUSE
FF/W
STILL ADV61 5
;EDP.B. ZOOM
(54)
(72)
(69)
(70)
PC Connection With DV Interface 
Cable
A video clip can be transferred directly to your PC 
(Personal Computer) via a DV Interface Cable 
PV-DDC9 (optional) using products and software 
from a number of video editing software 
companies.
Using products from video editing software 
companies allows you to capture and edit video 
clips using the DV Interface.
Our DVC being OHCI compliant should have 
no problem working with any OHCI compliant 
Firewire Video — Editing software package.
≥Personal Computer must be equipped with an 
DV Terminal.
≥During Camcorder playback, do not disconnect 
the DV Interface Cable or turn the Camcorder 
off as this may cause a PC hang-up error.
≥1394 (i. LINK) Interface must conform to OHCI 
(Open Host Controller Interface Specification).
DV
PV-GS33PP_Eng.book  38 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							With a PC (optional)
-39-
With a PC (optional)
Using the Software with a Computer
Following Software is not supplied with the 
Camcorder;
≥LSFT0577 (DV STUDIO 3.1E-SE)
≥K1HA05CD0005 (USB Cable)
An image stored on the DV Cassette can be 
transferred to your Personal Computer. If you 
would like to order, please refer to page 
-59-.
ªSoftware Installation (For Windows)1Turn on Personal Computer and start up 
Windows.
2Insert the CD-ROM into the Personal 
Computer’s CD-ROM drive.
≥The [Setup Menu] screen appears.
3Select the software to be installed from 
[Setup Menu].
≥USB Driver 
-39-:
This software Driver is for using DV STUDIO.
≥WebCam Driver 
-40-:
If the Camcorder is connected to your 
personal computer to the other parties via the 
network.
≥DV STUDIO 3.1E-SE (Optional Software) 
-43-:
With DV STUDIO 3.1E-SE software, your 
favorite scene on a tape can be captured to 
your personal computer as a still image. Also, 
images viewed through the camera lens can 
be captured to your personal computer.
≥Acrobat Reader
To view the installed operating instructions, 
Adobe Acrobat Reader 5.0 or higher is 
required. Please install Adobe Acrobat 
Reader from the CD-ROM (Optional 
Software).
4Follow the instructions on the computer 
screen until the installation is complete.
≥Setup window will disappear when the 
installation is complete.
≥If a window does not appear automatically, click 
the “Start” Button on your desktop and then 
click “Run”. When the “Run” Box is open, type in 
“D:\InstMenu.exe” and click “OK”. (“D” applies 
when the CD-ROM drive is drive D.)
Using USB Driver
ªOperating environment≥Despite having the operating environment 
indicated, it may not be possible to use the 
program with some types of personal 
computers.
≥A CD-ROM drive is requires to install this 
program.
OS:
IBM PC/AT compatible personal computer with 
pre-installed; 
Microsoft Windows XP Home Edition/ 
Professional
Microsoft Windows 2000 Professional
Microsoft Windows Me (Millennium Edition)
Microsoft Windows 98 Second Edition 
CPU:
Intel Pentium II/Celeron 300 MHz or higher
(including compatible CPU)
RAM:
32 MB or more (64 MB or more recommended)
(128 MB or more required for Windows XP)
Free hard disk space:
At least 30 MB or more
Ports:
USB Terminal
ªInstalling USB DriverPlease install USB Driver first before connecting 
the Camcorder to your Personal Computer with 
the USB Connection Cable.
1Turn on the Personal Computer and start up 
Windows.
2Insert the CD-ROM into the Personal 
Computer’s CD-ROM drive.
≥Quit all applications.
≥The [Setup Menu] screen appears.
3Click the [USB Driver].
≥The set up program strarts running.
4For Windows 98SE/Me/2000 users, click 
[Restart] if the [InstallShield] dialog 
appears.
≥Do not remove the CD-ROM.
5Finish installation by following the 
on-screen instructions.
≥Click [Next] and proceed with installation.
≥After completing the installation, Click 
[Finish].
6After the USB Driver is installed, please 
restart your computer.
≥Reboot the computer to finish installing USB 
driver.
≥Installation continues after the computer 
reboots if you selected additional software.
PV-GS33PP_Eng.book  39 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							With a PC (optional)
-40-
≥A message indicating a conflict between 
versions may be displayed during the 
installation. This will not cause a problem. 
Simply click [Yes] to proceed with the 
installation.
≥Depending on the OS version, illustrations and 
icon names may vary.
Windows 98SE/Me Users
The following messages may be displayed when 
connecting this Camcorder and your personal 
computer via USB Cable.
1For Windows 98SE Users:
The message, “Please insert the disk 
labeled ‘Windows 98 Second Edition 
CD-ROM’,.....” is displayed. Click [OK].
1) The message “The file ‘kstvtune.ax’ on 
[Unknown] cannot be found...” is displayed.
≥Enter “C:\Windows\system” for Windows 
98SE. Enter “C:\Windows\options\CABS” 
for Windows Me.
≥If the “kstvtune.ax” file is missing in one of 
the 2 above-mentioned folders, insert the 
OS CD-ROM and assign the path.
2) The message “The file ‘ksclockf.ax’ on 
[Unknown] cannot be found...” is displayed.
≥Enter “C:\Windows\system”.
≥If the “ksclockf.ax” file is missing in the 
above mentioned folder, insert the OS 
CD-ROM and assign the path.
≥You may click [Browse] to look for and assign 
the path.
ªConnecting the Personal Computer 
and Camcorder
Please install the USB Driver first before 
connecting the Camcorder to your Personal 
Computer with the USB Cable.
Before making these connections, turn off all 
devices which are to be connected.
≥When connecting the Personal Computer and 
Camcorder, use of the AC Adaptor is 
recommended for the power supply of the 
Camcorder.
Using as a Web Camera
If the Camcorder is connected to your personal 
computer, you can send video and sound from 
the Camcorder to the other parties via the 
network.
≥Do not connect the USB Cable until the 
WebCam is installed.
This feature can be used only if both parties 
are using the same operating system. Please 
see chart below:
ªOperating environmentOS:
IBM PC/AT compatible personal computer with 
preinstalled;
Microsoft Windows XP Home Edition/ 
Professional
(In this case of Windows XP SP1 or later is 
needed.)
Microsoft Windows 2000 Professional
Microsoft Windows Me (Millennium Edition)
Microsoft Windows 98 Second Edition 
CPU:
Intel Pentium II/Celeron 300 MHz or higher
(including compatible CPU)
RAM:
32 MB or more (64 MB or more recommended)
(128 MB or more required for Windows XP)
Free hard disk space:
At least 250 MB or more
Ports:
USB Terminal
To use the Camcorder as a Web Camera, the 
additional minimum requirements must be 
met.
Graphic display:
High Color (16 bit) or more
Desktop resolution of 800k600 pixels or more
Communication Speed:
56 kbps or faster is recommended
Necessary software:
Windows Messenger 5.0 or later (Windows XP)
MSN Messenger (Windows 98SE/Me/2000)
Other requirements (to send/receive audio):
Sound card
Speaker or headphones
[Send] [Receive] [Software]
Windows XPWindows XP Windows 
Messenger
Windows XPWindows 
98SE/Me/
2000
Windows 
98SE/Me/ 
2000Windows 
98SE/Me/ 
2000MSN 
Messenger
PV-GS33PP_Eng.book  40 ページ  ２００４年２月２６日　木曜日　午後５時２９分