Panasonic Pv Gs33 Operating Instructions Manual

							
Before Use
-11-
(22)Eyecup(23)Power LCD Button [POWER LCD] -17-Power LCD Lamp -17-
(24)
Cassette Holder(25)Cassette Compartment Cover -16-
(26)Speaker -32-
(27)USB Jack [ ] -41-
(28)S-Video Output Jack [S-VIDEO OUT] -36-
(29)White Balance Sensor -28-Remote Control Sensor -13-
(30)Jack for Magic Wire Remote Control with 
Narration Mic (optional) [REMOTE] -22-Microphone Jack [MIC]
≥ When connecting an external microphone 
or audio equipment to this jack, the built-in 
microphone does not operate.
≥ When connecting the Magic Wire Remote 
Control with Narration Mic (optional) to this 
jack and the [TALK] Button is pressed, the 
built-in microphone does not operate. (
-22-)
≥ When connecting the pin plug of the Magic 
Wire Remote Control with Narration Mic 
(optional) to this jack, plug it in as far as it 
goes.
≥ A compatible plug-in powered microphone 
can be used. Please c onsult your dealer for 
more information.
≥ The microphone may make noises 
depending on the type used. In this case, 
we recommend using the battery with the 
Camcorder to reduce noises instead of the 
AC adaptor.
(31)Audio-Video Output Jack [A/V OUT] -36-Headphone Jack [PHONES]
≥ Connecting an AV Cable to this jack 
activates the Camcorder’s built-in speaker, 
but connecting a headphone, etc. 
deactivates it.
≥ When connecting the pin plug of the AV 
Cable to this jack, plug it in as far as it goes.
S-VIDEO
OUT
A/V OUT 
PHONES
REMOTE/MIC
(PLUG IN POWER)
DV
(24)
(25)
(26)
(27)
 (28) (29)
(30)
  (31)  (32)
≥ When using headphones, set [AV JACK] of 
the [INITIAL] sub-menu to [OUT/PHONES]. 
If you set [AV JACK] to [OUT], you may 
hear noises on the right.
(32)DV Terminal [DV] -38-≥ Connect this to the digital video equipment.
(33)Viewfinder -17-,-54-
(34)
Eyepiece Corrector Knob -17-
(35)Photoshot Button [PHOTO SHOT] -23-
(36)Zoom Lever [W/T], [ sVOL/JOG r] -23-,-32-
(37)Cassette Eject Lever [OPEN/EJECT] -16-
(38)Reset Button [RESET] -47-
(39)Mode Dial -16-
(40)Quick Start Recording Button 
[QUICK START] -23-Quick Start Recording Lamp -23-
(41)Recording Start/Stop Button -21-
(42)Power Switch [OFF/ON] -16-,-21-,-51-
(43)[POWER] Lamp -16-,-21-,-32-
(44)
Mode Selector Switch 
[AUTO/MANUAL/FOCUS] -21-,-27-,-29-
(45)Shoulder Strap Holders -16-
(46)Grip Belt (One-touch Free Style Grip Belt) -15-
(47)Battery Eject Button [PUSH BATT] -14-
(48)Battery Holder(49)Tripod Receptacle
≥ Used for mounting the Camcorder on an 
optional tripod.
Due to limitations in LCD production 
technology, there may be some tiny bright or 
dark spots on the Viewfinder screen. 
However, this is not a malfunction and does 
not affect the recorded picture.
STARTONOFFQUICK
POWER
(33)(34)(35)(36)(37)(38)
(39)
(40)
(41)
(42)
(43)
(44)(45)(46)
(47)
 (48)       (49)
PV-GS33Eng_text.fm  11 ページ  ２００４年２月２７日　金曜日　午前１１時３６分 
						

							Before Use
-12-
ªRemote ControllerUsing the wireless Remote Controller that is 
supplied with the Camcorder, most of the 
Camcorder functions can be operated from a 
distance.
(50)Date/Time Button [DATE/TIME] -47-
(51)Indication Output Button [OSD] -36-
(52)Display Button [DISPLAY] -47-
(53)Reset Button [RESET] -57-
(54)Recording Button [¥REC] -38-
(55)Audio Dubbing Button [A.DUB] -37-
(56)Cursor Buttons for Variable Speed 
Search Function [π,∫] -33-Direction Buttons for Playback Zoom 
Function [π,∑,∏,∫] -35-
(57)
Slow Motion/Still Advance Buttons [E,D] 
(E: Reverse, D:Forward) -33-
(58)Index Search Buttons [:,9] 
(:: Reverse, 9: Forward) -34-
(59)Selection Button [SELECT] -35-
(60)Store Button [STORE] -35-
(61)Off/On Button [OFF/ON] -35-
(62)Zoom/Volume Button [ZOOM/VOL] -23-,-32-,-35-
(63)Variable Speed Search Button 
[VAR. SEARCH] -33-
(64)Menu Button [MENU] -18-
ZOOM
INDEX INDEXSELECTSTORESTOP
KL∫
OSDDISPLAY
V/REWSTILL ADV
OFF/ONP. B . D I G I TA L
DATE/
TIME
RESET
TITLE T
WsVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S EFF /WSTILL ADV
ENTER61 5;ED
VA R .
SEARCHMENU
P.B. ZOOM
(50)
(51)
(52)
(53)(54)
(55)
(56)
ZOOM
INDEX INDEXSELECTSTORESTOP
KL∫
OSDDISPLAY
V/REWSTILL ADV
OFF/ONP. B . D I G I TA L
DATE/
TIME
RESET
TITLE T
WsVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S EFF /WSTILL ADV
ENTER61 5;ED
VA R .
SEARCHMENU
P.B. ZOOM(57)
(58)
(59)
(60)
(61)(62)
(63)
(64)(65)
Photoshot Button [PHOTO SHOT] -23-
(66)Title Button [TITLE]
≥This Camcorder cannot be operated with 
this button.
(67)Multi-Picture/Picture-in-Picture Button 
[MULTI/P-IN-P] -30-
(68)Rewind/Review Button [6] -32-
(69)Pause Button [;] -33-
(70)Stop Button [∫] -32-
(71)Recording Start/Stop Button 
[START/STOP] -21-
(72)Play Button [1] -33-
(73)Fast-forward/Cue Button [5] -32-
(74)Playback Zoom Button [P.B. ZOOM] -34-
(75)Enter Button [ENTER] -18-
ªMagic Wire Remote Control with 
Narration Mic (optional)
Magic Wire Remote Control with Narration Mic 
is not included in this Model. If you wish to 
order, please refer to the page 
-59-.
This controller allows the scene to be shot from 
various angles, high to low, and is also 
convenient when a Tripod is used. When the 
controller is not in use, attach the clip to the Grip 
Belt for convenience.
This controller makes it easier for left-handed 
users to use the Camcorder.
(76)Microphone [MIC] -22-
(77)Recording Start/Stop Button [REC](78)Zoom Lever [W/T]
≥Zoom speed changes in 2 stages.
(79)Photoshot Button [PHOTO SHOT](80)Microphone Switch Button [TALK] -22-
ZOOM
INDEX INDEXSELECTSTORESTOP
KL∫
OSDDISPLAY
V/REWSTILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
WsVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S EFF /WSTILL ADV
ENTER61 5;ED
VA R .
SEARCHMENU
P.B. ZOOM
(65)
(66)(71)
(74)
(75) (72)
(73) (67)
(68)
(69)
(70)
(76)
(77)
(78)
(79)
(80)(81)
PV-GS33PP_Eng.book  12 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Before Use
-13-
≥When the Magic Wire Remote Control with 
Narration Mic is connected to [REMOTE] 
Jack and the [TALK] Button is pressed, the 
narration microphone is activated and the 
built-in microphone on the Camcorder is 
deactivated.
(81)Clip
≥Insert the plug securely into the [REMOTE] 
Jack as far as it will go. A loose connection 
will affect normal operation.
The Remote Controller
ªInserting a Button-type BatteryBefore using the Remote Controller, insert the 
supplied button-type battery.
1While pressing the Lock Button 1, pull out 
the Battery Holder.
2Insert the button-type battery with the (i) 
marking facing upwards.
3Insert the Battery Holder into the Remote 
Controller.
≥When the button-type battery is exhausted, 
replace it with a new CR2025 battery. (A battery 
is normally expected to last about 1 year. 
However, it depends on operation frequency.)
≥Make sure to match the poles correctly when 
inserting the battery.
Warning
Danger of explosion if battery is 
incorrectly replaced.
Replace only with the same or equivalent 
type recommended by the equipment 
manufacturer. Discard used batteries 
according to manufacturer’s instructions.
Risk of fire, explosion and burns. Do not 
recharge, disassemble, heat above 212°F 
(100°C) or incinerate. Keep the 
Button-Type battery out of the reach of 
children. Never put Button-Type battery 
in mouth. If swallowed, call your doctor.
1
ªUsing the Remote Controller
1Direct the Remote Controller at the Remote 
Control Sensor (29) of the Camcorder and 
press an appropriate button.
≥Distance from the Camcorder: Within 
approximately 15 feet (5 meters)
≥Angle: Approximately 15o in the vertical and 
horizontal directions from the central 
axis
≥The above operating ranges are for indoor use. 
Outdoors or under strong light, the Camcorder 
may not operate properly even within the above 
ranges.
≥Within a 3 feet (1 meter) range, you can also 
use the Remote Controller on the LCD Monitor 
side of the Camcorder.
Selecting Remote Controller Modes
When 2 Camcorders are used simultaneously, 
they can be operated individually by selecting 
different Remote Controller Modes.
≥If the Remote Controller Mode of the 
Camcorder and that of the Remote Controller 
do not match, [REMOTE] Indication is 
displayed.
Setup on the Camcorder:Set [REMOTE] on the [INITIAL] Sub-Menu to the 
desired Remote Controller Mode. (-19-)
Setup on the Remote Controller:
[VCR1]: Press the [D] Button and [∫] Button 
simultaneously. 1
[VCR2]: Press the [E] Button and [∫] Button 
simultaneously. 2
≥When the battery in the Remote Controller is 
replaced, the mode is automatically reset to 
[VCR1] Mode.Replace battery with Panasonic PART NO. 
CR2025 only. Use of another battery may 
present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep 
away from children. 
Do not recharge, disassemble or dispose of 
in fire.
15˚
15˚15˚ 15˚
(29)
INDEX INDEX
SELECT
STOPKL∫
STILL ADV
T
W
PAU S ESTILL ADV61 5
;EDP.B. ZOOM21
PV-GS33PP_Eng.book  13 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Before Use
-14-
Power Supply
ªUsing the AC Adaptor
1
Connect the DC Cable to the Camcorder.2Connect the DC Cable to the AC Adaptor.3Connect the AC Cable to the AC Adaptor 
and the AC Jack.
≥The AC Cable’s outlet plug does not fit 
entirely into the AC Adaptor jack. A gap will 
remain as shown 1.
≥Before connecting or disconnecting the 
power supply, set the [OFF/ON] Switch on 
the Camcorder to [OFF] and make sure that 
[POWER] Lamp is not lit.
ªUsing the BatteryBefore use, fully charge the Battery.
≥We recommend using a Panasonic Battery.
≥We cannot guarantee the quality of this 
Camcorder when batteries from other 
companies are used.
1Attach the Battery to the AC Adaptor and 
charge it.
≥Since the Battery will not be charged when 
the DC Cable is connected to the AC 
Adaptor, disconnect it from the AC Adaptor.
≥The [CHARGE] Lamp lights up, and charging 
starts.
≥When the [CHARGE] Lamp goes off, 
charging is completed.
≥When the battery is completely discharged, 
the [CHARGE] lamp blinks at first, but the 
battery is charged normally. When the 
temperature of the battery is too high or low, 
the [CHARGE] lamp blinks and the charging 
time becomes longer than usual.
2Attach the charged Battery to the 
Camcorder.
1
Disconnecting the Power SourceSet the [OFF/ON] Switch (42) to [OFF] and, while 
pressing the [PUSH BATT] Button (47), slide the 
Battery or DC Cable upward to disconnect it.
≥For other notes concerning this item, see 
-47-.
Charging Time and Available 
Recording Time
ACharging Time
BMaximum Continuous Recording Time
≥“1h30min.” indicates 1 hour and 30 minutes.
≥Battery CGA-DU07 is supplied.
≥The times shown in the table are approximate 
times. The numbers indicate the recording time 
when the Viewfinder is used. The numbers in 
parentheses indicate the recording time when 
the LCD Monitor is used. In actual use, the 
available recording time may be shorter.
≥The times shown in the table are for continuous 
recording at a temperature of 68oF (25oC) and 
humidity of 60%. If the Battery is charged at a 
higher or lower temperature, the charging time 
may be longer.
≥In the following cases, the available recording 
time becomes shorter.
≥You use the Viewfinder and LCD Monitor 
simultaneously when using the 0 Lux 
MagicPix function, rotating the LCD Monitor 
forward to record yourself.
≥When you set [EVF ON/AUTO] to [ON].
≥When you use the Camcorder while lighting 
the LCD Monitor up by pressing the 
[POWER LCD] Button.
CGA-DU07A1h30min.B2h15min. (1h50min.)
CGA-DU14A2h45min.B4h30min. (3h40min.)CGA-DU21A3h55min.
B6h45min. (5h30min.)
PUSH
BATT
ONOFF
(47)
(42)
PV-GS33PP_Eng.book  14 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Before Use
-15-
The One-touch Free Style Grip Belt
ªTo Use as a Grip BeltAdjust the length of the Grip Belt to the size of 
your hand.
1Detach the end of the Grip Belt.
2Adjust the length of the Grip Belt to the size 
of your hand.
3Reattach the Grip Belt.
ªTo Use as a Hand StrapUsing the Grip Belt as the hand strap makes it 
easier to handle and carry a Camcorder. It is 
more convenient to use with the Magic Wire 
Remote Control with Narration Mic (optional).
1Open the Lock Cover (20) by holding the 
tabs on both sides 1, press the Lock 
Button 
(19) and detach the Grip Belt.
2Detach the end of the Grip Belt.
3Slide A in the direction of the arrow and 
reattach the Grip Belt.
1(19) (20)
A
4Attach the Grip Belt around your wrist.
≥When returning the Grip Belt to the Grip Belt 
Attachment, press the Lock Cover 2 to ensure 
that it is securely locked.
Attaching the Lens Cap
To protect the Lens surface, attach the Lens Cap.1Pass one end of the Lens Cap Cord through 
the attached eye on the Lens Cap. Then 
pass the other end through the loop made 
by itself and pull tight.
2Pass the end of the Lens Cap Cord through 
the hole in the Grip Belt Attachment and the 
Lens Cap through the Lens Cap Cord.
≥The removed Lens Cap can be hooked onto the 
Grip Belt. (It is not possible when using as a 
hand strap.)
≥When you are not recording, be sure to cover 
the Lens with the Lens Cap for protection.
2
PV-GS33PP_Eng.book  15 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Before Use
-16-
Attaching the Shoulder Strap
We recommend that you attach the Shoulder 
Strap before going out to avoid dropping the 
Camcorder.
1Pull the end of the Shoulder Strap through 
the Shoulder Strap Holder (45) on the 
Camcorder.
2Fold the end of the Shoulder Strap, run it 
through the Shoulder Strap Length 
Adjuster, and pull it.
≥Pull it out more than 1 inch (2 cm) 1 from the 
Shoulder Strap Length Adjuster so that it 
cannot slip off.
≥Attach the other end of the Shoulder Strap to 
the other Shoulder Strap Holder in the same 
way.
Inserting a Cassette
1Slide the [OPEN/EJECT] Lever (37) toward 
the front and pull down to open the 
Cassette Compartment Cover.
2Insert a Cassette.
3Close the Cassette Holder by pressing the 
[PUSH] mark 1.
4Close the Cassette Compartment Cover.
(45)
1
OPEN /
EJECT(37)
PUSH
1
ªAccidental Erasure PreventionOpening the accidental erasure prevention slider 
1 on the cassette (by sliding it to the [SAVE] 
arrow direction) prevents recording. To enable 
recording, close the accidental erasure 
prevention slider (by sliding it to the [REC] arrow 
direction).
≥For other notes concerning this item, see 
-47-.
Turning on the Camcorder 
When the Camcorder is turned on with the Lens 
Cap on, the Automatic White Balance Adjustment 
may not function properly. Please turn on the 
Camcorder after removing the Lens Cap.
ªHow to Turn on the Power
1Set the [OFF/ON] Switch (42) to [ON] while 
pressing the button 1.
≥The [POWER] Lamp 
(43) lights up.
ªHow to Turn off the Power
1Set the [OFF/ON] Switch (42) to [OFF] while 
pressing the button 1.
Selecting Modes
You can choose a desired mode by rotating the 
Mode Dial.
1Rotate the Mode Dial (39).
:Tape Recording Mode
Use this mode when recording pictures on a tape.
:Tape Playback Mode
Use this mode when playing back the recorded 
scene on a tape.
R E CSAVE
1
ONOFF
POWER
1
(42)
(43)
ONOFF(42)1
(39)
PV-GS33PP_Eng.book  16 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Before Use
-17-
Using the Viewfinder/LCD Monitor
ªUsing the ViewfinderBefore using the Viewfinder, adjust the field of 
view so that the displays inside the Viewfinder 
become clear and easy to read.
1Pull the Viewfinder.
2Adjust by turning the Eyepiece Corrector 
Knob (34).
To Use the Viewfinder at the Same Time as the 
LCD Monitor
Set [LCD/EVF] >> [EVF ON/AUTO] >> [ON].
≥The Viewfinder does not turn off even if the LCD 
Monitor is opened.
≥When you turn the Camcorder off, this setting is 
cancelled.
ªUsing the LCD MonitorWith the LCD Monitor open, you can also record 
the picture while watching it.
1Using your Thumb on the [OPEN4] Knob (1) and pull the LCD Monitor (2) out in the 
direction of the arrow.
≥The Viewfinder is now deactivated.
≥The LCD Monitor can be opened a maximum 
of 120o. If you open the LCD monitor by 120o, 
it becomes convenient to operate menus or to 
play back pictures.
2Adjust the LCD Monitor angle according to 
the desired recording angle.
≥The LCD Monitor can rotate a maximum of 
180o 1 from the vertical position upwards 
and a maximum of 90o 2 to the downward 
direction. Forcefully rotating the LCD Monitor 
beyond these ranges will damage the 
Camcorder. You cannot rotate the LCD 
Monitor when it is opened to an angle of 120o. 
Therefore, do not rotate it forcibly.
12:30:45PM
OCT 15 200412:30:45PM
OCT 15 200412:30:45PM
OCT 15 2004
12:30:45PM
OCT 15 2004(34)
(2)
(1)
Closing the LCD Monitor
Push the LCD Monitor until it is securely locked.
ªAdjusting Brightness and Color LevelWhen [LCD/EVF SET] on the [LCD/EVF] 
Sub-Menu is set to [YES], the following items are 
displayed.
LCD Brightness [LCD BRIGHTNESS]
Adjusts the brightness of the image on the LCD 
screen.
LCD Color Level [LCD COLOR LEVEL]
Adjusts the color saturation of the image on the 
LCD screen.
Brightness of the Viewfinder 
[EVF BRIGHTNESS]
Adjusts the brightness of the image in the 
Viewfinder.
To AdjustPress the [;/∫] Button and select the item to be 
adjusted, and then press the [6/5] Button to 
raise or lower the number of vertical bars in the 
Bar Indication.
≥More vertical bars indicates stronger brightness 
or color saturation.
To Increase the Brightness of the Entire LCD 
Monitor
Press the [POWER LCD] Button (23).
When you press [POWER LCD] button, the LCD 
monitor becomes about twice as bright as usual.
≥The [POWER LCD] Lamp 
(23) lights up.
≥When turning the power on while using AC 
Adaptor, [POWER LCD] function is 
automatically effective.
To Resume Normal Brightness
Press the [POWER LCD] Button again.
≥These adjustments do not affect the recorded 
images.
≥For other notes concerning this item, see 
-54-.
290o 1180o
1LCD BRIGHTNESS
    [-]||||----[+]
 LCD COLOR LEVEL
    [-]||||----[+]
 EVF BRIGHTNESS
    [-]||||----[+]
 ;/∫:SELECT &/%:SETUP
            !/MENU:EXIT
LCD/EVF SETUP
POWER
LCD
(23)
PV-GS33PP_Eng.book  17 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Before Use
-18-
Using the Menu Screen
To facilitate the selection of a desired function or 
setup, this Camcorder displays various function 
setups on Menus.
≥When operating the menu with the Viewfinder, 
set [LCD/EVF] >> [EVF ON/AUTO] >> [ON] or 
rotate the LCD monitor by 180o.
1Press the [MENU] Button (14).
≥The Menu corresponding to the Mode 
selected by using the Mode Dial 
(39) is 
displayed.
2Press the [;/∫] Button to select a desired 
Sub-Menu.
≥Press the [;/∫] Button to display the 
highlighted item.
3Press the [5] Button to display the 
selected Sub-Menu.
4Press the [;/∫] Button to select the item.5Press the [5] Button to display the 
selected item.
6Press the [;/∫] Button to select the desired 
mode and press [ENTER] Button to 
determine the setting.
≥While a Menu is displayed, you cannot record or 
play back. Menus can be displayed during 
playback but not during recording. The above 
operations can be done using the [MENU] 
Button, [π,∑,∏,∫] Buttons and [ENTER] 
Button on the Remote Controller. (
-12-)
To Return the Previous ScreenPress the [6] Button.
To Exit the Menu ScreenPress the [MENU] Button again.
About the Menu Mode Setting
The setting selected on the Menu will be retained 
even when the Camcorder is turned off. (The 
setups of [EFFECT2] (
-30-) are not retained.) 
However, if the Battery or AC Adaptor is 
disconnected before turning off the Camcorder, 
the selected setup may not be retained.
≥Menu operation flow is shown in this text by >>.
MENU
STILL
ENTERFA D Ei s
(14)
(39)
List of Menus
The figures of the Menus are for explanation 
purposes only, and they are different from the 
actual Menus.
ª[TAPE RECORDING MENU]Tape Recording Menu
1) [CAMERA]
Camera Setup Sub-Menu
[PROG.AE]
Auto Exposure Mode 
-27-[EIS]
Image Stabilizer -24-[D.ZOOM]
Digital Zoom -24-[SHTR EFFECT]
Shutter Effect -22-[SELF TIMER]
Self-timer Recording -23-[USB FUNCTION]
USB Functions Mode -39-≥If you press [6] Button, the menu changes 
back to the previous screen.
2) [DIGITAL]
Digital Setup Sub-Menu
[EFFECT1]
Digital Effects 1 
-30-[EFFECT2]
Digital Effects 2 -30-[MULTI MODE]
Multi-Picture Mode -30-3) [RECORDING]
Recording Setup Sub-Menu
[REC SPEED]
Recording Speed Mode 
-20-[AUDIO REC]
Audio Recording Mode -20-[SCENE INDEX]
Scene Index Mode -34-[WIND CUT]
Wind Noise Reduction -26-[ZOOM MIC]
Zoom Microphone -24-[CINEMA]
Cinema-like Format Recording -27-4) [DISPLAY]
Display Setup Sub-Menu
[DISPLAY]
Display Mode 
-47-[DATE/TIME]
Date and Time Indication -47-[C.DISPLAY]
Counter Display Mode -46-
;/∫:SELECT       %:NEXT
               MENU:EXIT
DIGITAL
CARD
DISPLAY
LCD/EVF
INITIAL RECORDINGSIS
D.ZOOM
SELF TIMER
USB FUNCTION PROG.AETAPE RECORDING MENUCAMERA    !
;/∫:SELECT       %:NEXT
               MENU:EXIT
DIGITAL
DISPLAY
LCD/EVF
INITIAL RECORDINGEIS
D.ZOOM
SHTR EFFECT
SELF TIMER
USB FUNCTION PROG.AETAPE RECORDING MENUCAMERA     !
PV-GS33PP_Eng.book  18 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Before Use
-19-
[C.RESET]
Counter Reset -57-≥It resets the counter to zero. However, it cannot 
reset the Time Code.
5) [LCD/EVF]
LCD/EVF Setup Sub-Menu
[LCD/EVF SET]
LCD and Viewfinder Adjustment 
-17-[SELF REC]
Recording Yourself -23-[EVF ON/AUTO]
Using the Viewfinder -17-6) [INITIAL]
Initial Setup Sub-Menu
[BLANK SEARCH]
Blank Search 
-22-[DEMO MODE]
Demonstration Mode
≥If no operation takes place for approximately 
10 minutes after the AC Adaptor is connected to 
the Camcorder and the [OFF/ON] Switch is 
turned to [ON] without inserting a Cassette, the 
Camcorder is automatically set to 
Demonstration Mode for introducing its 
functions. If any button is pressed or operated, 
the Demonstration Mode is cancelled. The 
Demonstration Mode can be started by setting 
[DEMO MODE] to [ON] and by exiting the 
Menu. To terminate the Demonstration Mode, 
insert a Cassette or set the [DEMO MODE] to 
[OFF].
[AV JACK]
AV Jack 
-55-[REMOTE]
Remote Controller Mode -13-[REC LAMP]
Recording Lamp -21-[BEEP SOUND]
Beep Sound -48-[CLOCK SET]
Date and Time Setting -20-[INITIAL SET]
Initial Setting Mode -47-
ª[TAPE PLAYBACK MENU]Tape Playback Menu
1) [PLAYBACK]
Playback Functions Sub-Menu
[SEARCH]
Index Search Mode 
-34-[12bit AUDIO]
Audio Selector -37-[AUDIO OUT]
Audio Output Mode -50-2) [DIGITAL]
Playback Digital Setup Sub-Menu
[EFFECT ON]
Digital Effect On/Off 
-35-[EFFECT SEL]
Digital Effect Selection -35-3) [RECORDING]
Recording Setup Sub-Menu
[REC SPEED]
Recording Speed Mode 
-20-[AUDIO REC]
Audio Recording Mode -20-4) [DISPLAY]
Display Setup Sub-Menu
[DISPLAY]
Display Mode 
-47-[DATE/TIME]
Date and Time Indication -47-[C.DISPLAY]
Counter Display Mode -46-[C.RESET]
Counter Reset -57-5) [LCD/EVF]
Adjusting Brightness and Color Level
[LCD/EVF SET]
LCD and Viewfinder Adjustment 
-17-[EVF ON/AUTO]
Using the Viewfinder -17-6) [INITIAL]
Initial Setup Sub-Menu
[BLANK SEARCH]
Blank Search 
-22-[AV JACK]
AV Jack -50-[REMOTE]
Remote Controller Mode -13-[REC LAMP]
Recording Lamp -21-[BEEP SOUND]
Beep Sound -48-
;/∫:SELECT       %:NEXT
               MENU:EXIT
DIGITAL
RECORDING
DISPLAY
LCD/EVF
INITIAL12bit AUDIO
AUDIO OUT SEARCHTAPE PLAYBACK MENUPLAYBACK   !
PV-GS33PP_Eng.book  19 ページ  ２００４年２月２６日　木曜日　午後５時２９分 
						

							Before Use
-20-
Setting Date and Time
Since the internal clock of the Camcorder has a 
slight imprecision make sure to check the time 
before recording.
1Set [TAPE RECORDINGMENU] >> [INITIAL] 
>> [CLOCK SET] >> [YES].
2Press the [;/∫] Button to select [YEAR], 
[MONTH], [DAY], [HOUR] or [MIN.] and 
press the [6/5] Button to set it to the 
desired value.
≥Year will cycle in the order shown below.
2000, 2001, ..., 2089, 2000, ...
3Press the [MENU] Button (14) to finish 
setting the date and time.
≥The clock operation starts from [00] second.
≥If the built-in battery is weak, the [0] or [--] 
Indication flashes. In this case, charge the 
built-in battery.
≥The clock uses the 12-hour system.
MENU
STILL
ENTERFA D Ei s
(14)
CLOCK SET
1YEAR  :2004
 MONTH :JUL
 DAY   :12
 HOUR  : 3PM
 MIN.  :17
 ;/∫:SELECT &/%:SETUP
            !/MENU:EXIT
Internal Lithium Battery Recharge
The internal lithium battery sustains the operation 
of the clock. When the [0] or [--] Indication 
flashes, the internal lithium battery is near 
exhaustion.
1Connect the AC Adaptor to the Camcorder 
with the power turned off and then connect 
to the AC Jack.
≥After charging for 4 hours, the built-in lithium 
battery can power the clock for approximately 
3 months.
LP Mode
A desired recording speed can be selected with 
[REC SPEED] on the [RECORDING] Sub-Menu.
If LP Mode is selected, the recording time 
becomes 1.5 times longer than that of SP 
Mode.
Although the image quality does not decrease 
with the LP Mode recording, mosaic-pattern noise 
may appear on a playback image, or some 
normal functions may be restricted.
≥The contents that are recorded in LP Mode are 
not completely compatible with other 
equipment.
≥Audio dubbing is not possible with LP Mode. 
(
-37-)
Audio Recording Mode
The sound quality of the recorded sound can be 
selected with [AUDIO REC] on the 
[RECORDING] Sub-Menu.
High sound-quality recording is possible with 
“16 bit 48 kHz 2 track” Mode. With the “12 bit 
32 kHz 4 track” Mode, the original sound can be 
recorded on 2 tracks in stereo, while the other 
2 tracks can be used for Audio Dubbing.
PV-GS33PP_Eng.book  20 ページ  ２００４年２月２６日　木曜日　午後５時２９分