Panasonic Pv Dv202 Operating Instructions Manual

							41
Digital Features
Digital Features
VCR mode
1Set POWER to VCR.
2Press MENU to display the VCR
MENU screen.
3Rotate JOG KEY to select PLAY
 FUNCTION , then press JOG KEY
to display the VCR PLAY FUNCTION
menu screen.
4Rotate JOG KEY to select D.ZOOM ,
then press JOG KEY to select ON.
Press MENU twice to exit.
5Press  (PLAY) to start playback.
The center portion of the image
doubles in size.
6Repeat steps 2~4 to select OFF to
cancel this feature.
5PLAY
Color recording of video or still images onto
the Mini DV tape in low lighting.
(pp. 43, 108)
MagicPix™ Images
1Set POWER to CAMERA.
2Press MENU to display the menu
screen.
3Rotate JOG KEY to select
 D.FUNCTION , and then press JOG
KEY to display the CAMERA
FUNCTION menu screen.
4Rotate JOG KEY to select
 D.FUNCTION , and then press JOG
KEY repeatedly to select MAGICPIX.
Press MENU twice to exit.
5To cancel the Digital Function, press
JOG KEY repeatedly to select OFF.
MagicPix cannot be used with still
images on the Memory Card.
(See “Card PhotoShot” on page 48.)Note
Digital Zoom (Continued)
2MENU
1POWER
3, 4JOG KEY
2MENU
1POWER
3, 4JOG KEY
EVF/LCD
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
45 
						

							42For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Digital Features
EIS ON NORMAL
1Set POWER to CAMERA.
2Press EIS to stabilize the picture.
Picture flicker may be observed when
taping under fluorescent lighting
conditions.
The EIS indicator flashes when the
light level is inadequate.
Turn D.E.I.S. OFF during recording
when using a tripod.
3Press REC/PAUSE to start recording.
4Press EIS again to cancel.
 Be sure that D.E.I.S. is turned off
when not needed.
Dual Digital Electronic Image
Stabilization System (D.E.I.S.)
This feature helps compensate for any
unintentional hand or body movement. It
can be used in both the Recording and
Playback (VCR) modes.
CAMERA mode
VCR mode
Other Digital Functions are turned off
automatically when the EIS and Digital
Zoom are selected.
ASet POWER to VCR.
BPress  (PLAY) to start playback.
CPress EIS to stabilize the picture.
DPress EIS again to cancel.
 Be sure that D.E.I.S. is turned off
when not needed.
Note
When using D.E.I.S in VCR mode, the
image size is slightly larger.
Note
1, APOWER
2, 4, C, DEIS
BPLAY
D.E.I.S. may not function when...
Palmcorder movement is too
extreme.
Recording a subject with distinct
horizontal or vertical stripes.
Recording in low light situations.
Recording a subject under a great
amount of fluorescent light.
Recording a scene with very fast
motions.
3REC/PAUSE
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
46 
						

							43
Digital Features
Digital Features
1Set POWER to CAMERA or VCR.
2Press MENU to display the menu
screen.
3Rotate JOG KEY to select
 D.FUNCTION in the CAMERA mode
menu screen or PLAY FUNCTION in
the VCR mode menu screen, then
press JOG KEY to display the
CAMERA FUNCTION or VCR PLAY
FUNCTION menu screen.
4Rotate JOG KEY to select
 D.FUNCTION , and then press JOG
KEY repeatedly to select one of the
Digital Functions listed on the left.
5To cancel the Digital Function, press
JOG KEY repeatedly to select OFF.
The EIS and Digital Zoom features are
turned off automatically when one of the
Digital Functions listed at left is
selected.
Other Digital Functions
Use the following features to add interest
and professionalism to your recordings or
playback. Select from twelve special
effects.
Note
Types of Digital Functions
MIRROR
Symmetrical image from the current
camera picture.
STROBE
The recording appears as a sequence of
still frames.
MOSAIC
The picture appears in a mosaic pattern.
SLIM
The picture is expanded vertically.
TRAIL
The subject being recorded creates a trail
when in motion.
STRETCH
The picture is expanded horizontally.
MAGICPIX (Not available during playback)
Color recording of video or still images onto
the Mini DV in low lighting. (p. 41)
 Only Manual Focus is available.
WIPE
Successive scenes are separated in a way
which simulates the drawing of a curtain.
MIX
The current scene is mixed in with the
following scene during scene changes.
PinP
PinP (Still image) is displayed on the
Main Picture.
SEPIA (Only available during playback)
The picture is played back in sepia, a
brownish color, giving it an antique look.
MONO (Monotone) (Only available during
playback)
The picture is played back in black-and-
white.
To use the WIPE function
a.In Camera mode, set the “D.FUNCTION”
item in the main menu screen to “WIPE”.
(Menu OSD: p. 108)
b.Press REC/PAUSE to start recording.
c.Press REC/PAUSE to pause the
recording. The last scene will be
memorized.
d.Press RECORD/PAUSE to start
recording again. The new scene will take
the place of the memorized scene.
To use the MIX function
a.In Camera mode, set the “D.FUNCTION”
item in the main menu screen to “MIX”
(Menu OSD: p. 108). Then, perform steps
b-d above.
The memorized scene and the new
scene will appear mixed as the scene
changes from one to the other.
When Photo Title is set, WIPE/MIX mode
becomes Photo Title. When Photo Title
is finished, Digital Function turns OFF.
Note
2MENU
1POWER
3, 4, 5JOG KEY
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
47 
						

							44For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
External Microphone
with M3 connector (not
supplied)
External
Microphone Jack
(PV-DV402 only) The original sound can be replaced with
new sound using the built-in Palmcorder
microphone or an external microphone
(PV-DV402 only).
Audio Dubbing using the
External (PV-DV402 only) or
Built-in Microphone
1Set POWER to VCR.
With the Remote Control, you can set
the Palmcorder to stop automatically
at a specified point on the tape. See
“Memory-Stop Editing” on page 45.
2Press  (PLAY). Then press (PAUSE) where you  want dubbing to
begin.
3Press MENU to display the VCR mode
menu screen.
Rotate JOG KEY to select REC MODE ,
then press JOG KEY to display the
VCR REC MODE menu screen.
Rotate JOG KEY to select AUDIO-
 DUB , and then press JOG KEY to
select ON.
The Palmcorder will go to Stand By
mode, and “A.DUB” flashes in the EVF
or the LCD monitor. Go to step 4.
2PLAY
2PAUSE
3A.DUB
Before you beginConnect the external Microphone
(if used) (PV-DV402 only).
Turn on the Palmcorder.
Insert a pre-recorded tape to be dubbed.
Built-in Microphone
The AUDIO-REC setting in CAMERA
MENU mode should be as follows:
Select 12 bit if you do not want the
original sound to be completely replaced
during an audio dub.
If you dub over a tape which has both
12 bit and 16 bit audio recordings on it,
keep in mind that the original 16 bit audio
portion will be completely replaced.
12 bit
16 bitThe original sound is recorded
on ST (Stereo) 1, and the new
sound will be recorded on ST
(Stereo) 2.
The original sound is replaced
with the new sound.
1POWER
3JOG KEY
3MENU
When using the Palmcorder only
When using the Remote Control only
3Press A.DUB on the Remote Control.
The Palmcorder will go to Stand By
mode, and “A.DUB” flashes in the
EVF or the LCD monitor. Go to step 4.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
48 
						

							45
Editing Features
Editing Features
4Press  (PAUSE) to start Audio
Dubbing.
Connect the Palmcorder to the TV in
order to monitor the sound.
(p. 39)
Only NTSC (National Television Standards
Committee) recorded tapes can be audio
dubbed. The following screen appears if
the tape was not recorded in NTSC format.
5Press  (PAUSE) to stop Audio
Dubbing. To listen to the desired audio sound, set
the AUDIO setting of the VCR mode MENU
(Menu OSD: p. 110) as follows:
If the microphone used for dubbing gets
too near the speaker of your TV,
a howling noise (feedback) may occur.
If the tape position is in or was started in
a blank section, you cannot use the
A.DUB feature.
Memory-Stop Editing (Remote
Control Only)
16 bit dubbed sound completely erases
the original 16 bit recorded sound.
If you dubbed using 12 bit AUDIO
recording and then selected AUDIO-MIX
in the menu for playback, the sound will
be stereo regardless of the AUDIO-OUT
setting.
If you recorded in LP mode, you cannot
use the A.DUB feature.Note
You can set an automatic Dubbing stop
point.
DRESET
AMENU
APress MENU to display the VCR
menu screen.
BRotate JOG KEY to select DISPLAY
 SETTING , and then press JOG KEY
to display the DISPLAY SETTING
menu.
CRotate JOG KEY to select DISPLAY ,
and then press JOG KEY to set to
MEMORY.
DPress MENU two times to exit MENU
mode. Then, press RESET on the
remote control to reset the Counter
Memory to M 0:00:00.
Now, rewind to the editing start point,
and continue with steps 2-5. The tape will
now stop automatically at “M 0:00:00”.
ST 1
ST 2
MIXSet this position to listen to the
original sound.
Set this position to listen to the
audio dubbed sound.
Set this position to listen to both
the original sound and the audio
dubbed sound.
AUDIO:The following selections are
available for 12 bit AUDIO dubbed
recordings only (sound recorded in SP
mode only).
4, 5PAUSE
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
49 
						

							46For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
Video In
S-Video In
VHF Connecting
Cable (not
supplied)TV
(To View)
A/V Cable
(Supplied)
To Audio In
To Video In
Recording:
VCR (Rear)
To S-Video In
(If there is S-Video In)
For technical reasons, dubbing a tape
may reduce its quality.
Press DISPLAY ON TV on the
Palmcorder Remote Control to eliminate
EVF/LCD Monitor indications.
If the Time Code is displayed in the EVF
or LCD monitor, it cannot be reset.
Only the DATE/TIME, when displayed,
will be recorded on the tape.
    CAUTION:Unauthorized exchanging and/or
copying of copyrighted recordings may
be copyright infringement. A/V OUT S-VIDEO OUT Source (Playing)
Palmcorder
Copying your Tapes to
S-VHS or VHS Cassette
Monitor with your TV
1Insert a pre-recorded tape
into the source (playing) Palmcorder
and a blank tape, with record tab in
place, into the target VCR (Recorder).
2Press  (PLAY) on the Palmcorder.
When the tape reaches the point you
want to start dubbing, press PAUSE.
3Place the VCR into REC/PAUSE
mode. (See VCR manual.)
4Simultaneously, press PAUSE on
both units to begin copying.
5Press STOP on both units when
copying is completed.
S-Video
Cable (not
supplied)
Audio In
Note
Turn the TV ON and select its VCR
channel (either CH3 or CH4).
Set the VCR/TV Selector on the
recording VCR to VCR.
Before you begin
Connect both Palmcorder and VCR to
their power sources.
Connect the Palmcorder to a VCR as
illustrated left.
Turn ON both units.
Set the recording VCR’s Input Signal
Selector to LINE.
Set the Palmcorder POWER to VCR.
Before using S-VIDEO Connector,
insert the DC Cable into the DC IN
Terminal. (p. 15)
DC Cable
(Supplied)
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
50 
						

							47
Editing Features
Editing Features
3, 4PLAY
3, 4, 5PAUSE3, 4PLAY
6STOP
4REC High quality digital-to-digital copying can
be accomplished if both Palmcorders
incorporate the DV Input/Output (i.LINK)
Connector (DV interface cable (i.LINK) is
not supplied).
1Insert a pre-recorded tape into the
source (playing) Palmcorder, and set
POWER to VCR.
2Insert a blank tape with the record
tab closed into the target (recording)
Palmcorder and set POWER to VCR.
3Press  (PLAY) on the source
Palmcorder. When the tape reaches
the point you want to start dubbing,
press 
 (PAUSE).
4Hold down REC and press  (PLAY)
on the target (recording) Palmcorder or
on the remote control.
Press 
 (PAUSE) to pause the tape at
the starting point of the dub.
5Simultaneously, press  (PAUSE) on
both units to begin dubbing.
6Press  (STOP) on the recording
unit, and then press  (STOP) on the
playing unit to end dubbing.
When two Palmcorders are used for
dubbing, it is recommended that the
Remote Control VCR1 or VCR2 setting be
used to avoid improper-operation.
When two Palmcorders are connected
using the DV interface cable (i.LINK) (not
supplied), a Video Editing Controller
cannot be used.
Do not connect both an S-Video Cable or
A/V Cable and a DV Interface Cable
(i.LINK).
    CAUTION:Unauthorized exchanging and/or
copying of copyrighted recordings may
be copyright infringement.
Source (Playing)
Palmcorder
Recording
Palmcorder
DV Interface
Cable (i.LINK)
(optional)
DV Input/Output
(i.LINK) Connector
Copying from Digital
Equipment (dubbing)
Note
3, 4, 5PAUSE
Before you beginConnect both Palmcorders to their
power sources.
Connect the two Palmcorders using the
DV interface cable (i.LINK)
(4-pin to 4-pin).
Turn both Palmcorders ON.
6STOP
4REC
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
51 
						

							48For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Card Features
You can record still images to a Memory
Card.
1Slide the M-CARD Lock Switch to
unlock, then set POWER to M-CARD.
The POWER lamp lights red.
Be sure POWER is fully turned to
M-CARD position.
“PLAY: PUSH PLAY KEY” is
displayed for 10 seconds. (p. 50)
2Press MENU to display CARD
SETTING menu, then press JOG KEY
to select NORMAL or FINE .
Press MENU to exit this menu.
3Press PHOTOSHOT to record an
image.
The PhotoShot image is recorded to
the Memory Card.
When SHUTTER is set to ON (Menu
OSD: p. 108), still pictures are
recorded with a visual shutter effect
and click sound. If set to OFF, the still
image will be displayed only.
1POWER
2JOG KEY
3PHOTOSHOT
Image Resolution and Capacity
(supplied 8MB Memory Card)
REC
Mode
FINE
NORMAL
Image
Resolution
1280 x 960
640 x 480Capacity
Approx. 30 images
Approx. 70 images
The number of images given for each
mode applies when all images are taken in
same mode.
You can change recording modes at any
time before capturing an image.
The number of images that can be
captured may differ depending on the
subject. After capturing an image, the
number may not decrease, or it may
decrease by two. This is normal.
While “PROCESSING” is displayed, DO
NOT turn off the Palmcorder or unplug
the AC Adaptor (supplied) because this
will cause irreversible damage to the
memory.
Before you beginConnect the Palmcorder to a power
source. (pp. 14, 15)
Set POWER to OFF before inserting a
Memory Card. (p. 13)Card PhotoShot
Memory Card will not work when DV
interface Cable (i.LINK) is connected.
Warning
Warning
M-CARD
Lock
2MENU
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
52 
						

							49
Card Features
1Repeat steps 1 and 2 on page 48.
2Set POWER to VCR.
3Press  (PLAY) to start playback of
the cassette tape. And then, press 
(PAUSE) to select an image.
4Press PHOTOSHOT to record the
desired image to the Memory Card.
When PHOTOSHOT is pressed in
PLAY or SLOW mode, the screen
goes to STOP mode.
To playback the images of the
Memory Card, see page 50.
When Variable Speed Search is
done (p. 35), this feature can
not be used.
5Repeat steps 3~4 to record another
image to the Memory Card.
You can record still images from a
cassette tape to a Memory Card.
3PLAY
Before you beginConnect the Palmcorder to a power
source. (pp. 14, 15)
Set POWER to OFF before inserting a
Memory Card. (p. 13)Recording images From a
Tape
3PAUSE Memory Card will not work when DV
interface Cable (i.LINK) is connected.
Warning
Card Features
Cautions for the Memory Card
While Memory Card data is being read, do not remove it, tur n off the power, or subject
unit to vibrations and/or shocks.
Do not leave the Memor y Card in a place with high temperature, a place exposed to
direct sunlight, or a place where electromagnetic waves and static electricity can be
generated.
Electromagnetic waves, static electricity, malfunction of the Digital Video Palmcorder or
of the Memory Card itself could erase the data recorded on it. To prevent the loss of
picture data, we recommend that you make a backup copy on the computer.
Do not bend or drop the Memor y Card as this could damage it or the captured
contents.
Do not touch the connector on the rear edge of the Memory Card with your fingers and
take care that no dir t, dust or water enters it.
Do not affix other labels to the Memory Card face or back as Card inser tion/removal
may become impossible.
2POWER
4PHOTOSHOT
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
53 
						

							50For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
1Slide the M-CARD Lock Switch to
unlock, then set POWER to M-CARD.
“PLAY: PUSH PLAY KEY” is
displayed for 10 seconds.
2Press  (M-PLAY) to display the Multi
playback screen.
“PLEASE WAIT” appears on-screen.
Rotate JOG KEY to scroll through
Multi image screen pages (6 images
per page) and select an image.
The selected image is underlined in
green.
Press MENU to display CARD
SETTING menu screen.
Press 
 (M-STOP) to return to the
Card PhotoShot REC Mode. (p. 48)
3Press JOG KEY to display the
selected image as a full-size screen.
“PLEASE WAIT” appears on-screen.
4Rotate JOG KEY to select BACK
(previous image), MULTI (Multi Image
screen), or NEXT (next image).
Press 
 (M-STOP) to return to the
Multi Playback screen.
NoteIf the file number is changed, the
Palmcorder cannot read the file data.
This product is compliant with DCF
(Design rule for Camera File System).
Images saved on the Memory Card
using other Digital Still Cameras that are
compliant with DCF can be viewed on
this product.
While “PLEASE WAIT” is displayed, DO
NOT turn off the Palmcorder or unplug
the AC Adaptor (supplied) because this
will cause irreversible damage to the
memory.
2M-PLAY
M-STOP
Warning
You can view the images on the Memory
Card.
Before you beginSet POWER to OFF before inserting a
recorded Memory Card. (pp. 48, 49)Playback Still Images
“PLEASE WAIT” is displayed.
1POWER
3, 4JOG KEY
M-CARD
Lock
Card Features
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402
54