Panasonic Pv Dv202 Operating Instructions Manual

51
Card Features
Card Features
3M-DEL
M-STOP You can delete unwanted images and
increase the remaining image memory.
Warning:Once deleted, images cannot be restored.
DELETE PAGE
Delete specific images from a page.
DELETE ALL
Delete all images. (p. 52)
FORMAT
Delete all data. (p. 53)
2M-PLAY
While deleting image, DO NOT turn off
the Palmcorder or unplug the AC
Adaptor (supplied) because this
will cause irreversible damage to the
memory, resulting in reduced image
storage capacity.
Before you begin
Set...

52For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Card Features
1Do steps 1 and 2 on page 51.
2Press  (M-DEL) to display the
DELETE menu. Then, rotate and
press JOG KEY to select ALL .
The screen below is displayed.
To cancel delete, press 
 (M-STOP)
or rotate and press JOG KEY to
select NO.
3Rotate and press JOG KEY to select
 YES .
“PLEASE WAIT” is displayed on the
screen, and then “NO PICTURE” is
displayed.
Press 
 (M-STOP) to return to the...

53
Card Features
Card Features
1Do steps 1 and 2 on page 51.
2Press  (M-DEL) to display the
DELETE menu, then rotate and press
JOG KEY to select FORMAT .
The screen below is displayed.
To cancel format, press 
 (M-STOP)
or rotate and press JOG KEY to
select NO.
3Rotate and press JOG KEY to select
 YES .
“PLEASE WAIT” is displayed on the
screen as all image data is deleted
from Memory Card. Deletion is
complete when “NO PICTURE” is
displayed.
Press 
 (M-STOP) to return to the
Card PhotoShot REC Mode...

54For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Card Features
DPOF Setting
You can select the images to be printed,
the number of prints, and other
print-related information (DPOF setting) on
a Memory Card. “DPOF” stands for Digital
Print Order Format, and since printing data
can be added to images on the Memory
Card, the Memory Card can be used with
any system that provides DPOF.
Before you beginSet POWER to OFF before inserting a
recorded...

55
PC Connection
You can transfer images from your Palmcorder tape to your PC (Personal Computer).
Transferring Your  Images  (Windows)
IBM PC/AT or compatible
Pentium ll Processor: 266 MHz or more
RAM: 64 MB or more
CD-ROM drive (for installation)
Mouse or other pointing device
Windows
 95 (for ArcSoft Software only)/98SE/
Me/2000/XP preinstalled PC with USB port
2 MB minimum available hard disk space
(for Palmcorder USB Device Driver)
15 MB minimum available hard disk space (for
PHOTOVU/MPEG4...

56For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Caution
Software Installation (Windows 95 (for ArcSoft Software only/
98SE/Me/2000/XP)
Please install Palmcorder USB Device Driver first before connecting the Palmcorder and
your PC using USB Cable. Once Palmcorder USB Device Driver is installed, you must
restart your computer for installation to take effect.
Restarting the computer not only applies to Driver installation, but must be done
whenever...

57
PC Connection
Notes on PHOTOVU/MPEG4 Movie Messenger™ System operation
For PHOTOVU/MPEG4 Movie Messenger™ System, do not connect the i.LINK and
USB terminals to the Palmcorder at the same time.
Make sure Palmcorder power is not shut off during use as your PC system may become
unstable. Therefore, the AC Adaptor should be used as the power source. (Be
especially careful when recording in M-CARD or CAMERA mode as the power
eventually shuts off automatically if a tape is inserted.)
For PHOTOVU/MPEG4...

58For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
PHOTOVU/MPEG4 Movie Messenger™ System
3
2
USB TerminalUSB Terminal
1Turn on your PC.
2Set the Palmcorder POWER to VCR.
3Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied).
“CAPTURE” appears in the EVF or the LCD monitor.
The “Found New Hardware Wizard” screen of Windows is displayed.
The following message       is displayed. Even so, functionality confirmation has
been...

59
PC Connection
PHOTOVU/MPEG4 Movie Messenger™ System
For Windows 2000 users
3Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied).
“CAPTURE” appears in the EVF or the LCD monitor.
The “Found New Hardware” screen of Windows is displayed.
When the Palmcorder and PC (with Windows 2000) are connected via USB, a
message, such as the one below, is displayed.
The following message is displayed. Even so, functionality confirmation has
been performed at our manufacturer.
Click [Yes] and...

60For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Running the PHOTOVU/
MPGE4 Movie Messenger™
System*Before you beginInsert a recorded tape. (p. 11)
*PHOTOVU: You can transfer Still images
from your Palmcorder tape to a PC.
MPEG4 Movie Messenger™ System:
You can transfer Motion images from your
Palmcorder tape to a PC.
1Set Palmcorder POWER to VCR.
2Connect the Palmcorder to your PC
using the USB Cable (supplied) or
DV interface Cable (i.LINK)...