Panasonic Projector Pt L780ntu Specifications

91
Wireless card /Projector LAN card  
Fitting
q
q
Turn off the power to the
projector
Turn off the power referring to  How
to turn off the power supply  given on
page  31.
w
w
Open the slot cover
e
e  
Insert the wireless /LAN card
With the side of  LED facing
up, insert the card until it reaches the
depth and is locked.
Note: • Pay attention to the difference
between up and down sides of the
card. Forcible insertion of the
card in a wrong direction may
cause a fault.
r
r
Close the slot cover
Removal
q...

92
How to use SD card
Setting 
q q
Press the MENU button to view the
menu
w w
Using the  and  buttons, show the
SD card screen
e e
Press the ENTER button to show the
SD card setting screen.
r r
Using the and buttons, select the
desired item, and make setting with the
and buttons.PICTUREPICTURE MODE
COLOR TEMP.
BRIGHT
CONTRAST
SHARPNESS
WHITE BALANCE R
WHITE BALANCE G
WHITE BALANCE B
STANDARDSTANDARD
STANDARD
32
32
6
32
32
32
SELECT:[^][@]
ADJUST:[{][}]ENTER:[ENTER]
  ESC:[MENU]
SD CARDAUTOPLAY
REPEAT...

93
Replay
q q
Change to SD card using the input
switching (RGB) button of the projector
or remote controller.
w w
Select the folder with the  and
buttons and press the
ENTER button.
A file selection screen will appear.
Notes: •If three or more folders are found, press the
button and the next three (or less)
folders will be shown in turn.
•If no thumbnail has been incorporated in the
image file in advance, it will take a longer
time before image appears.
•A folder that contains no image file cannot
be...

94
Recording directly on SD card
Use the SD card by means of a PC card adaptor in a personal computer hav\
ing a slot
that is compatible to TYPE 2 or TYPE 3 PC (PCMCIA) card.
For a Windows machine, the supplied software, Image Creator 1.0, will be\
 available
for compiling and storing.
For details of Image Creator 1.0, refer to Image Creator 1.0 on page 130.
Compiling on Windows
If your PC is a Windows machine, the supplied software, Image Creator 1.\
0 can be
used. With this Image Creator 1.0, the user...

95
If this is the second or forward time of SD card insertion, no setting o\
peration is
required.
r
r
Select Create list of all drivers
existing in specific location and select
the driver for installation and click the
Next button.
t
t
Select Standard IDE/ESDI hard disk
controller and click the Next button.
From now on, go on installation operation following
the instructions on the screen. Finally, click the
Complete button to finish the preparatory
operation for SD card use.
y
y
Open My Computer on the...

96Removing SD card
Take out the SD card in the following procedure:
q q
Quit all software applications that use the SD card.
w w
Left-click the PC card icon ( ) shown on the task bar at the
right bottom on the screen.
Note: 
•If no PC card icon is appearing on the task bar at the right bottom of the screen, go
to Start menu →Setting →Control panel, open PC card, click the Show control
on the task bar check box, and then click the OK button.
e e
Select either Disable standard
IDE/ESDI hard disk controller...

97
Compilation on Macintosh machine The supplied software, Image Creator 1.0, is not available in Macintosh \
machines.
However, it is possible to write and compile images stored in the person\
al computer.
Fitting SD card
q
q
Insert the SD card into the PC card
adaptor as shown in the diagram on
the right.
Positively push in the card until it is locked. Also
pay attention to the difference between up and
down sides and fore and back sides when
inserting the card.
Note: •If the SD card is inserted in the...

98Saving images in Macintosh onto the SD card.
JPEG images that were created with graphic software or captured by digit\
al camera
into Macintosh can be saved onto the SD card and replayed with the proje\
ctor.
Note: 
•
  Fully read DCF standard on page  136 and perform file operation.
q
q
Open the icon of SD card drive and press the   + N
buttons to create a new folder (directory) and rename it DCIM.
A DCIM directory already exists in an SD card in which any file has been\
 saved
as a result of image...

99
Network setting
Example of setting for use of the
wireless card
Image transfer methods that use wireless card are broadly classified int\
o four types
depending on the current working environment.
To use wireless communication for the first timeInsert the optional wireless card (ET-CDWL1) into your PC and make set\
ting for the
direct wireless communication with the projector.
For details of setting the projector, refer to Setting the projector o\
n page 104.
For details of setting the PC, refer to...

100
If wireless communication has already been
established between PCs (in ad hoc mode) 
In this case, it is required to make settings so that direct wireless co\
mmunication will
be available between the personal computers and the projector in ad hoc \
mode using
the wireless cards that are currently used in the PCs.
For details of setting the projector, refer to Setting the projector o\
n page 104.
R
Personal computer Personal computerProjector
Typical setting
Setting of the projectorParameters
IP...