Panasonic Projector Pt L780ntu Specifications

101
Use the same SSID setting as the access point. Please
consult your network administrator.
If wireless communication has already been
established using an access point
In this case, it is required to make settings so that wireless communica\
tion will be
available between the personal computers and the projector in infrastruc\
ture mode
through the access point.
Communication may not be established depending on the access point used.\
For details of setting the projector, refer to Setting the...

102
Setting of the projector
R
Personal 
computerPersonal computerProjector
Typical setting
Parameters
IP address
Assign an IP address that is different from that of PC.
Example: If the IP address of the PC is 192.168.10.11, assign
an address such as 192.168.10.12 to the projector.
Subnet mask
Mode
ChannelUse the same settings as the PC.
PEER-TO-PEER
Use the same setting as the PC.
If communication in ad hoc mode is unavailableMake setting for use in PEER-TO-PEER mode, which allows direct communica\...

103
To directly connect a personal computer to the
projector
Mount an optional projector LAN card 
(ET-CDLAN1) on the projector, connect
the PC to this card with a cross cable, and
then make setting for communication.
For details of setting the projector, refer
to Setting the projector on page 104.
For details of setting the PC, refer to
Settings of personal computer on page
112 .
Setting of the projectorSetting of the PC
Example of setting for use of the
projector LAN card
Usage of projector LAN card is...

104
Setting up the projector
Mounting a wireless card
q
q
Insert the wireless card into the projector
For details of installing and removing the wireless card, refer to Wire\
less card on
page  91.
w
w
Press the MENU button to display the menu.
e
e
Use and buttons to display
Network setting screen.
r
r
Press the ENTER button to display Network setting setting screen.
StatusFive different LAN settings (LAN 1-5) can be stored on the projector.
Selecting from LAN 1-5 with  and  buttons, press the ENTER...

105
GatewayThis is a relaying point to connect two networks. It does not work in ad\
 hoc mode.
This address must be specified when connecting to a network of a differe\
nt
segment in infrastructure mode or peer-to-pee mode or to connect to the \
Internet.
For the details of specification of address, consult your network admini\
strator.
Host nameSet the name of the projector on the network.
The name must be up to 16 alphanumeric characters and symbols.
Use  and  buttons to change the value, and use  and...

106
KEY SIZE (encryption key size)Set the size of the key required for the encrypted communication.
Conform to the setting of the personal computer and the access point. In some
cases, 64 bits may be indicated as 40 bits and 128 bits as 104 bits.
Use  and  buttons to toggle the values and press the ENTER button
when the setting is completed.
KEY ID (encryption key ID)Specify the ID of the encryption key to be used.
Conform to the setting of the personal computer and the access point.
Use  and  buttons to...

107
Installing a wireless card driver
Install a wireless card driver onto the personal computer in order to use the wireless
card.
Fitting and removal of wireless card into/from
personal computer 
Insertion of wireless card
With the side of power monitor
facing up, insert the card into the
PC card slot until it reaches the
depth.
Pay attention to the difference between the
up and down sides of the wireless card.
Notes:•Refer carefully to the instruction manual supplied with the PC.
•Forcible insertion of...

108
Installing a driverWhen the wireless card is inserted, the driver installation screen will appear. A driver is stored
in the CD-ROM supplied with the projector. Use the following procedure for installation.
When installing a driver, the setting utility is installed automatically. Installation screen
does not appear.
For Windows98SE
Note:•The Windows98SE installation CD-ROM may be required when installing the
driver.
q q
When the wireless card is inserted, Add
New Hardware Wizard appears. Press
Next...

109
 For WindowsMe
q
q
Set the CD-ROM to the CD-ROM drive,
select Automatic search for a better
driver and press the Next button.
w w
Press the Finish button.
 For Windows2000
q
q
When the wireless card is inserted,
New Hardware Found Wizard appears.
Press the Next button.
w w
Select Search for a suitable driver for
my device, and press the Next
button.
e e
Insert the supplied CD-ROM into the CD-
ROM drive of the PC, click the check
box for CD-ROM drive, and press the
Next button.
r r
Press the Browse...

110
t t
When pananic.inf is detected, press the
Next button.
y y
Press the Yes button.
Installation of the driver will be started.
u u
Press the Finish button.
Installation of the driver will be completed.
 For WindowsXP
q
q
When the wireless card is inserted, New
Hardware Found Wizard appears. Press
the Next button.
w w
Uncheck Search removable media, check
Include this lacation in the search, click
the Browse button and then select
WirelessCard\English in the CD-ROM
drive for driver search location.
e...