Panasonic Projector Pt F200e Operating Instructions

ENGLISH - 41
Settings
SECURITY menu
JEntering the SECURITY menu
Every time when you apply to the SECURITY 
menu, you will be asked to perform the password 
operation.
When you apply to the SECURITY menu before you 
change the password to your original, perform to input 
the following factory default password operation.
 Press F H G I F H G I and ENTER.
QAfter you change the password
When you apply to the SECURITY menu after you 
change the password to your original in the 
PASSWORD CHANGE menu, input the...

ENGLISH - 42
Settings
NETWORK menu
In NETWORK menu, the following items are available.
 WIRED LAN
 WIRELESS LAN
 NAME CHANGE
 INPUT PASSWORD
 PASSWORD CHANGE
 NETWORK STANDBY
 WEB CONTROL
 LIVE MODE CUT IN
 STATUS
 INITIALIZE
NOTE:
• The NETWORK menu is available only with 
PT-F200NTE.
• See the PJ Link or network information in the contents 
of the CD-ROM which is provided with the projector.
• When INPUT PASSWORD in SECURITY menu is 
activated, perform the correct password operation to 
initialise the...

ENGLISH - 43
Maintenance
LAMP, TEMP and FILTER Indicators
If a problem should occur with the projector, the LAMP, TEMP and/or 
FILTER indicators will inform you. Manage the indicated problems as 
follow.
1. Confirm the status of all indicators and projector, and switch off the 
projector in proper way.
2. Find out the cause of the problem by status of the LAMP, TEMP 
and/or FILTER indicators.
3. Follow the instruction for each indication below and solve the 
problem.
4. Turn on the projector in the...

ENGLISH - 44
Maintenance
Care and Replacement
JBefore cleaning the projector
 Switch off the MAIN POWER and disconnect the mains plug from the mains socket.
 Unplug all the cables from the projector.
JCleaning the outer surface of the projector
Wipe off dirt and dust gently with a soft cloth.
 If it is difficult to remove the dirt, soak a cloth with water, wring the cloth well and then wipe the projector. 
Dry off the projector with dry cloth.
 Do not use petroleum benzine, thinner, any alcoholic...

Care and Replacement
ENGLISH - 45
Maintenance
JResetting the FILTER 
REMAINING
1. Turn on the projector and display the FILTER 
REMAINING in OPTION menu. Press the ENTER 
button for 3 seconds and the confirmation screen 
will be displayed. 
2. Press I to select OK and press the ENTER 
button to reset FILTER REMAINING to “0”. 
See 
“FILTER REMAINING” on page 38.
JBefore replacing the Lamp unit
 Switch off the MAIN POWER and disconnect the mains plug from the mains socket.
 Wait for more than 1 hour and...

Maintenance
Care and Replacement
ENGLISH - 46
JReplacement procedure
QRemoving and replacing the lamp unit
1. Use a Phillips-head screwdriver to loosen the 2 
Lamp unit cover fixing screws on the back of the 
projector until the screws turn freely, and remove 
the Lamp unit cover.
2. Use a Phillips-head screwdriver to loosen the 2 
Lamp unit fixing screws.
3. Hold the handles of the Lamp unit and release the 
lamp unit lock.
4. Pull the used Lamp unit gently from the projector.5. Replace the new Lamp...

ENGLISH - 47
Maintenance
Troubleshooting
Should any problem persist, contact your dealer.
ProblemCauseReference 
page
Power does not turn on.
 The mains lead may not be connected.
 The MAIN POWER switch is turned off.
 No electric supply is at the mains socket.
 TEMP indicator is lit or flashes.
 LAMP indicator is lit or flashes.
 The lamp unit cover has not been securely installed.
 The circuit breakers have tripped.23
24
23
43
43
46
-
No picture appears.
 The video signal input source may not be...

ENGLISH - 48
Appendix
Technical Information
List of compatible signals
Mode
Display 
resolution 
(dots)
*1
*1. The “i” appearing after the resolution indicates an interlaced signal.
Scanning 
frequencyDot clock 
frequency
(MHz)Picture 
quality
*2
*2. The following symbols are used to indicate picture quality.
AAMaximum picture quality can be obtained.
ASignals are converted by the image processing circuit before picture is projected.
BSome loss of data occurs to make projection easier.Terminals
H (kHz)V...

Technical Information
ENGLISH - 49
Appendix
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface 
specification, so that the projector can be controlled by a personal computer which is connected to this connecter.
JConnection
JPin assignments and signal names
JCommunication settings
JBasic format
 The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds 
before sending the command.
 If sending multiple...

Appendix
Technical Information
ENGLISH - 50
JCable specifications
(When connected to a personal computer)
JControl commands
You can switch the signals which to output from the COMPUTER1 OUT terminal by pressing the computer key 
command. The key commands are depend on the manufactures. If you select the computer terminals which has no 
signals while the INPUT GUIDE is set to DETAILED, the computer connection guidance will be displayed. 
CommandControl contentsRemarks
PONPower ONIn standby mode, all...