Panasonic Projector Pt F200e Operating Instructions

Getting Started
ENGLISH - 21
Connections
 Read and follow the operating and connecting instructions of each peripheral device.
 The peripheral devices must be turned off.
 Use cables that match each peripheral device to be connected.
 If the input signal is affected by signal jitter, the projected image may have poor image quality and timebase 
correction is effective.
 Confirm the type of video signals. See “List of compatible signals” on page 48.
JLAN terminal
(PT-F200NTE only)
Before connection to the...

Getting Started
Connections
ENGLISH - 22
JConnecting with VIDEO IN/S-VIDEO IN
JConnecting with COMPONENT IN
Connecting example: AV equipment
NOTE:
• When you connect more than one AV equipment, switch the audio connection manually.
DVD player
Audio system To S-VIDEO output
Video player
To video output or 
audio output
OR
DVD player
Video player
Audio system To audio output 

ENGLISH - 23
Basic Operation
Switching the projector on/off
JConnecting
1. Make sure the shape of the mains plug and the 
AC IN terminal on the back of the projector match, 
then push the plug all the way in.
2. Align the side of the power cord secure lock with 
the side guide rail of the AC IN terminal of the 
projector and slide it in.
3. Place the latch to the latch catcher and press until 
it clicks.
4. Connect the mains lead to a mains socket.
JDisconnecting
1. Unplug the mains lead from the mains...

Basic Operation
Switching the projector on/off
ENGLISH - 24
1. Switch the MAIN POWER on.
 The power indicator lights up in RED.
2. Open the Front panel cover.
 This is not necessary in Remote control operation.
3. Press the POWER button.
 The power indicator lights up in GREEN after 
flashing for a while.
 The STARTUP LOGO is displayed on the screen. 
See “STARTUP LOGO” on page 38.
1. Open the Front panel cover.
 This is not necessary in Remote control operation.
2. Press the POWER button.
 The...

Basic Operation
Switching the projector on/off
ENGLISH - 25
POWER indicator
Indicator statusStatus
No illumination or flashingThe MAIN POWER is switched off.
REDLitThe MAIN POWER is switched on and the projector is in standby.
When the LAMP or TEMP indicator is flashing, the POWER indicator will 
not be lit.
FlashingNetwork connection is ready while the POWER is turned off.
(PT-F200NTE only)
GREENFlashingThe POWER is switched on and the projector is getting ready to project.
LitThe projector is ready to...

ENGLISH - 26
Basic Operation
Projecting an image
1. Switch on the connected devices.
 Press the play button of the required device.
2. Press the INPUT SELECT buttons to select the 
required input method if needed. See “Switching 
the input signal” on page 28.
 The image will be projected on the screen.
1. Open the Front panel cover.
2. Adjust the projected image with the Lens shift 
lever. See “Lens shift and positioning” on page 19.
3. Adjust the angle of the projector.
 Screw down the Front leg...

ENGLISH - 27
Basic Operation
Remote control operation
You can operate the projector with the Remote control 
within the remote range 15 m (492), approximately 
± 30° vertically and horizontally.
QFacing to the projector
Ensure the Remote control emitter is facing to 
the Remote control signal receptor on front/back 
of the projector and press the required buttons to 
operate.
QFacing to the screen
Ensure the Remote control emitter is facing to 
the screen and press the required buttons to 
operate the...

Basic Operation
Remote control operation
ENGLISH - 28
You can switch the input method manually by 
pressing the COMPUTER, NETWORK 
(PT-F200NTE only) and VIDEO buttons. 
Press the required button several times or I 
H to cycle through the input methods as 
follows. The actual projected image will be 
changed in a while.
 The graphical guidance will be displayed on the upper 
right of the projected image and you can confirm the 
selected input method which is highlighted in yellow. See 
“INPUT GUIDE” on...

Basic Operation
Remote control operation
ENGLISH - 29
When projecting an image, press FREEZE to 
capture the projected image and display it on 
the screen as a still picture. While the image is 
frozen, the sound will be stopped.Press the FREEZE button to return to the projection.
You can turn off the lamp and stop the 
projection temporary for electrical power save. Press the SHUTTER button to return to the projection.
You can reset most of the customised settings 
to the factory defaults by pressing...

Basic Operation
Remote control operation
ENGLISH - 30
You can enlarge the projected image down 
to a centred area for emphasizing within the 
range of 1x to 2x.
QEnlarging the image
1. Press DIGITAL ZOOM +/- once.
 The centred area of the image will then be enlarged 
to 1.5x.
2. Adjust the image size by pressing DIGITAL ZOOM 
+/-.
 The image size will be changed in steps of 0.1.
QShifting the centre point
Press F G I H to shift the centre point.
You can control the volume of the built-in 
speakers and...