Panasonic Projector Pt F200e Operating Instructions

ENGLISH - 31
Settings
Menu Navigation
The menu system allows you to access functions which do not have their own dedicated buttons on the Remote 
control. The menu options are structured and categorised. You can navigate through the menu with F G H I 
buttons.
JDisplaying the Main menu
Press the MENU button to display the Main 
menu and the operating guidance.
JAdjusting with the bar scale 
items
The triangle mark under the bar indicates factory 
default setting and the square indicates the current...

Settings
Menu Navigation
ENGLISH - 32
The Main menu has 6 options. Select the required menu item and press ENTER to display the Sub-menu. 
Main menu and Sub-menu
NOTE:
• Some default settings vary by the selected input signal.
•Sub-menu items vary according to the selected input signal.
• Some settings are adjustable without any signals.
Main menuSub-menuOptions (underlined is default setting)Page
PICTURE PICTURE MODE NATURAL
DYNAMIC
*1
*1. Default setting for COMPUTER/NETWORK signalspage 34
STANDARD...

Menu Navigation
ENGLISH - 33
Settings
Main menuSub-menuOptions (underlined is default setting)Page
OPTION INPUT GUIDE DETAILED
SIMPLEpage 38
OFF
STARTUP LOGO ON
OFFpage 38
USER
COMPUTER2 SELECT INPUT
OUTPUTpage 38
FILTER REMAININGpage 38
LAMP RUNTIMEpage 38
POWER OFF TIMER OFF
page 39
15 MIN. 20 MIN.
25 MIN. 30 MIN.
35 MIN. 40 MIN.
45 MIN. 50 MIN.
55 MIN. 60 MIN.
DIRECT POWER ON OFF
ONpage 39
CONTROL PANEL VALID
INVALIDpage 39
AUTO SETUP AUTO
BUTTONpage 39
SIGNAL SEARCH ON
OFFpage 39
INSTALLATION...

ENGLISH - 34
Settings
PICTURE menu
Depending on the projection environment, you can use 
these preset parameter settings to optimise image 
projection. Press I H to cycle through the options.
You can adjust the contrast of the projected image. 
Adjust the BRIGHTNESS in advance if necessary.
You can adjust the brightness of the projected image.You can adjust the colour saturation of the projected 
image. (Available with signals from VIDEO/S-VIDEO/
COMPONENT only)
You can adjust the skin tone in the...

PICTURE menu
ENGLISH - 35
Settings
You can perform more detailed image adjustment 
manually.
JFor S-VIDEO/VIDEO signals
QTV-SYSTEM
When the video signal is changed, the setting 
switches automatically. You can switch the setting 
manually to match the video data. Press I H to 
cycle through the options.
QSTILL MODE
You can reduce the vertical flicker when projecting 
a still image.
 OFF: Deactive
 ON: Active
QNOISE REDUCTION
You can switch the automatic noise reduction 
system on/off. Press I H to select...

ENGLISH - 36
Settings
POSITION menu
If the projector is aligned non-perpendicularly to the 
screen, or if the projection screen has an angled surface, 
you can correct keystone.
You can move the projected image for fine adjustment. 
Press I H to move horizontally and F G vertically. 
(Available with signals from VIDEO/S-VIDEO/
COMPUTER/COMPONENT only)If you have interference patterns of the projected image, 
which is sometimes referred to as moire or noise, you 
can minimize it by pressing I H to adjust...

POSITION menu
ENGLISH - 37
Settings
Q16:9
The squeezed signal will be projected in 16:9 ratio.
QS4:3
The input signal will be sized down 75 % and 
projected. S4:3 mode is effective when projecting 
4:3 image on to a 16:9 screen.
QAUTO
The S1 signal which contains an identifying signal 
will be detected and automatically project the 
image in proper ratio. (Available with S-VIDEO 
signals only)When the input signal resolution is lower than the 
projector resolution, it will be projected at the projector...

ENGLISH - 38
Settings
OPTION menu
When you change the input method, the guidance 
appears in the upper right corner of the screen. The 
following display methods are available. Press I H to 
cycle through the options.
You can switch the logo on/off that is displayed when 
starting up the projector. Press I H to select the 
required option. STARTUP LOGO will be displayed for 
30 seconds.
 ONActive
 OFFDeactive
 USERDisplay the original text
QEditing the original text
If you select USER, you can display...

OPTION menu
ENGLISH - 39
Settings
You can set the off timer to switch off the POWER of the 
projector after a certain period of time automatically 
when no signal is detected. Press I H to select the 
required period from 15 to 60 minutes at intervals of 
5 minutes.
You can switch the projector start up status. Press I H 
to select the required option.
 OFFStarts in the same mode as last use.
 ONSkips the standby mode and starts 
the projection.
You can turn off the function of the control panel buttons...

Settings
OPTION menu
ENGLISH - 40
You can use the 7 different test patterns to adjust the 
focus of the image. See “Lens shift and positioning” on 
page 19. 
1. Press ENTER to display the test pattern 1.
2. Press I H to select the required test pattern.
3. Press MENU or RETURN to return to the previous 
menu, oar press repeatedly to escape the menu 
mode.
You can perform more detailed setting in various items.
JOSD DESIGN
You can change the background colour of the 
menu. Press I H to select the required...