Panasonic Projector PT-DZ16KU User Manual

							Chapter 4 Settings — Menu navigation
ENGLISH - 61
Main menu itemPage
[P IN P] 11 2
[TEST PATTERN]11 4
[SIGNAL LIST]11 5
[SECURITY]11 8
[NETWORK]122
Sub‑menu
The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu.
[PICTURE] 
Sub‑menu itemFactory defaultPage
[PICTURE MODE] [ST
ANDARD]
*164
[CONTRAST] [0]64
[BRIGHTNESS] [0]65
[COLOR] [2]*
165
[TINT] [-2]65
[COLOR TEMPERATURE] [DEFAULT]65
[GAMMA] [DEFAULT]67
[SYSTEM DAYLIGHT VIEW] [OFF]68
[SHARPNESS] [8]68
[NOISE REDUCTION] [2]69
[DYNAMIC IRIS] [2]69
[SYSTEM SELECTOR] [YP
BPR]*170
*1 Depends on the signal input.
Note
 fThe factory default settings may vary depending on the picture mode.
[POSITION] 
Sub‑menu item Factory defaultPage
[SHIFT] ―72
[ASPECT] [DEF
AULT]
*172
[ZOOM] ―73
[CLOCK PHASE] [0]74
[GEOMETRY] [OFF]74
*1 Depends on the signal input.
[ADVANCED MENU] 
Sub‑menu item Factory defaultPage
[DIGIT
AL CINEMA REALITY] [AUTO]
*177
[BLANKING] ―77
[INPUT RESOLUTION] ―78
[CLAMP POSITION] [24]
*178
[EDGE BLENDING] [OFF]79
[FRAME RESPONSE] [NORMAL]80
[RASTER POSITION] ―80
*1 Depends on the signal input.   
						

							Chapter 4 Settings — Menu navigation
62 - ENGLISH
Note
 fSub-menu items and factory default settings vary depending on the selected input terminal.
[DISPLAY LANGUAGE] 
Details (x page 82)
[DISPLAY OPTION] 
Sub‑menu item Factory defaultPage
[COLOR MA
TCHING] [OFF]83
[LARGE SCREEN CORRECTION] [OFF]84
[SCREEN SETTING] ―84
[AUTO SIGNAL] [OFF]85
[AUTO SETUP] ―85
[BACKUP INPUT SETTING] ―86
[RGB IN] ―87
[DVI-D IN] ―87
[HDMI IN] ―88
[SDI IN] ―88
[ON-SCREEN DISPLAY] ―89
[BACK COLOR] [BLUE]90
[STARTUP LOGO] [DEFAULT LOGO]91
[UNIFORMITY] ―91
[SHUTTER SETTING] ―91
[FREEZE] ―92
[WAVEFORM MONITOR] [OFF]92
[CUT OFF] ―93
[PROJECTOR SETUP] 
Sub‑menu item Factory defaultPage
[PROJECT
OR ID] [ALL]95
[PROJECTION METHOD] [FRONT/FLOOR]95
[COOLING CONDITION] [AUTO]96
[HIGH ALTITUDE MODE] [OFF]96
[LAMP SELECT] [QUAD]96
[LAMP RELAY] [OFF]97
[BRIGHTNESS CONTROL] ―98
[STANDBY MODE] [NORMAL]102
[SCHEDULE] [OFF]103
[STARTUP INPUT SELECT] [LAST USED]104
[RS-232C] ―104
[STATUS] ―106
[NO SIGNAL SHUT-OFF] [DISABLE]107
[REMOTE2 MODE] [DEFAULT]107
[FUNCTION BUTTON] ―107
[DATE AND TIME] ―108
[LENS CALIBRATION] ―109
[LENS MEMORY] ―109
[SAVE ALL USER DATA] ―11 0
[LOAD ALL USER DATA] ―111
[INITIALIZE] ―111
[SERVICE PASSWORD] ―111   
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 63
[P IN P] 
Details (x page 112)
[TEST PATTERN] 
Details (x page 114)
[SIGNAL LIST] 
Details (x page 115)
[SECURITY] 
Sub‑menu itemFactory defaultPage
[SECURITY
 PASSWORD] [OFF]11 8
[SECURITY PASSWORD CHANGE] ―11 8
[DISPLAY SETTING] [OFF]11 9
[TEXT CHANGE] ―11 9
[CONTROL DEVICE SETUP] ―11 9
[CONTROL DEVICE PASSWORD CHANGE] ―120
[NETWORK] 
Sub‑menu item Factory defaultPage
[NETWORK SETUP] ―122
[NETWORK CONTROL] ―122
[NETWORK ST
ATUS] ―123
[Art-Net SETUP] ―123
Note
 fSome items may not be adjusted or used for certain signal formats to be input to the projector .
The menu items that cannot be adjusted or used are shown in black characters, and they cannot be selected.
 f Sub-menu items and factory default settings vary depending on the selected input terminal.   
						

							Chapter 4 Settings — [PICTURE] menu
64 - ENGLISH
[PICTURE] menu
On the menu screen, select [PICTURE] from the main menu, and select an item from the sub‑menu.
Refer to “Navigating through the menu” (x
  page   59) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to adjust.
[PICTURE MODE]
You can switch to the desired picture mode suitable for the image source and the environment in which the projector is used.
1) Press  as to select [PICTURE MODE].
2)  
Press the 
 qw.
 fThe  [PICTURE MODE] individual adjustment screen is displayed.
3) Press  qw to switch the item.
 fThe items will switch each time you press the button.
[STANDARD] The image becomes suitable for moving images in general.
[CINEMA] The image becomes suitable for movie contents.
[NATURAL] The image is sRGB compliant.
[DICOM SIM.] The image becomes similar to that of DICOM Part 14 Grayscale Standard.
[DYNAMIC] The light output is maximized for use in bright areas.
[GRAPHIC] The image becomes suitable for input from the personal computer.
[USER] Set any desired picture mode.
Note
 fThe factory default picture mode is [GRAPHIC] for still image input signals and [ST ANDARD] for movie-based input signals. fDICOM is an abbreviation of “Digital Imaging and COmmunication in Medicine” and is a standard for medical imaging devices.  Although the 
DICOM name is used, the projector is not a medical device, and should not be used for purposes such as diagnosis of display images.
 f Press the  button when each [PICTURE MODE] is selected to save as a specified value when a new signal is input.  The data of 
all items except [SYSTEM SELECT

OR] in the [PICTURE] menu is saved.
 fIn the factory default settings, [USER] is set to images that comply with the ITU

- R BT.709 standard.
Changing the [USER] name
1) Press as to select [PICTURE MODE].
2)  
Press 
 qw to select [USER].
3)
 
Press the  button.
 f The  [PICTURE MODE] detailed screen is displayed.
4) Press  as to select [PICTURE MODE NAME CHANGE], and press the  button.
 fThe  [PICTURE MODE NAME CHANGE] screen is displayed.
5) Press  asqw to select the text, and press the  button to enter the text.
6)  
Press 
 asqw to select [OK], and press the  button.
 fThe picture mode name is changed.
[CONTRAST]
You can adjust the contrast of the colors.
1) Press  as to select [CONTRAST].   
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 65
2) Press qw or the  button.
 fThe  [CONTRAST] individual adjustment screen is displayed.
3) Press  qw to adjust the level.
Operation AdjustmentRange of adjustment
Press the w button. The screen becomes brighter.
-31 - +31
Press the q button. The screen becomes darker.
Attention
 f
Adjust [BRIGHTNESS] first when you need to adjust the black level.
[BRIGHTNESS]
You can adjust the dark (black) part of the projected image.
1) Press  as to select [BRIGHTNESS].
2)  
Press 
 qw or the  button.
 fThe  [BRIGHTNESS] individual adjustment screen is displayed.
3) Press  qw to adjust the level.
Operation AdjustmentRange of adjustment
Press the w button. Increases the brightness of the dark (black) parts of the screen.
-31 - +31
Press the q button. Reduces the brightness of the dark (black) parts of the screen.
[COLOR]
You can adjust the color saturation of the projected image.
1) Press 
as to select [COLOR].
2)  
Press 
 qw or the  button.
 fThe  [COLOR] individual adjustment screen is displayed.
3) Press  qw to adjust the level.
Operation AdjustmentRange of adjustment
Press the w button. Deepens colors.
-31 - +31
Press the q button. Weakens colors.
[TINT]
You can adjust the skin tone in the projected image.
1) Press 
as to select [TINT].
2)  
Press 
 qw or the  button.
 fThe  [TINT] individual adjustment screen is displayed.
3) Press  qw to adjust the level.
Operation AdjustmentRange of adjustment
Press the w button. Adjusts skin tone toward greenish color.
-31 - +31
Press the q button. Adjusts skin tone toward reddish purple.
[COLOR TEMPERATURE]
You can switch the color temperature if the white areas of the projected image are bluish or reddish.
Adjusting with color temperature
1) Press 
as to select [COLOR TEMPERATURE].   
						

							Chapter 4 Settings — [PICTURE] menu
66 - ENGLISH
2) Press qw or the  button.
 fThe  [COLOR TEMPERATURE] individual adjustment screen is displayed.
3) Press  qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Factory default setting.
[USER1] Adjusts white balance as desired. Refer to “Adjusting desired white balance” ( x
  page   66) for 
details.
[USER2]
[3200K] 
‑  [9300K] Allows you to set in increments of 100
  K. Select so that images become natural.
Note
 fWhen [PICTURE MODE] ( x   page   64) is set to [USER] or [DICOM SIM.], [DEFAULT] cannot be selected. fWhen [COLOR MA
TCHING] (x   page   83) adjustment is set to other than [OFF], [COLOR TEMPERATURE] is fixed to [USER1].
 fThe color temperature numerical values are guidelines.
Adjusting desired white balance
1) Press  as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe  [COLOR TEMPERATURE] individual adjustment screen is displayed.
3) Press  qw to select [USER1] or [USER2].
4)  
Press the  button.
 f The  [COLOR TEMPERATURE] screen is displayed.
5) Press  as to select [WHITE BALANCE].
6)  
Press the  button.
 f The  [WHITE BALANCE] screen is displayed.
7) Press  as to select [WHITE BALANCE HIGH] or [WHITE BALANCE LOW].
8)  
Press the  button.
 f The  [WHITE BALANCE HIGH] screen or the [WHITE BALANCE LOW] screen is displayed.
9) Press  as to select [RED], [GREEN], or [BLUE].
10)  
Press 
 qw to adjust the level.
Item Operation Adjustment Range of adjustment
[RED] Press the w button.
Deepens red.
[WHITE BALANCE HIGH]: 0 - +255 (factory default is +255)
[WHITE BALANCE LOW]: 
-127 - +127 (factory default is 
0)
Press the q button.
Weakens red.
[GREEN] Press the w button.
Deepens green.
Press the q button. Weakens green.
[BLUE] Press the w button.
Deepens blue.
Press the q button. Weakens blue.
Note
 f
Adjust [COLOR  TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment 
does not look suitable, you can press the  button on the remote control to return the setting for the selected item only to the 
factory default setting.
Adjusting desired white balance based on existing color temperature settings
1) Press  as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe  [COLOR TEMPERATURE] individual adjustment screen is displayed.
3) Press  qw to select an item other than [DEFAULT], [USER1], and [USER2].   
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 67
4) Press the  button.
 fThe  [CHANGE TO *****] screen is displayed.
5) Press  as to select [USER1] or [USER2].
 fThe status of the color temperature changed is saved to the selected item.
6) Press the  button.
 fThe confirmation screen is displayed.
7) Press  qw to select [OK], and press the  button.
 fThe [USER1] or [USER2] data is overwritten.
 fIf you press 

qw to select [CANCEL] and then press the  button, the data will not be overwritten.
 fThe 

[WHITE BALANCE HIGH] screen is displayed.
8) Press  as to select [RED], [GREEN], or [BLUE].
9)  
Press 
 qw to adjust the level.
Note
 f Adjust [COLOR  TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment 
does not look suitable, you can press the  button on the remote control to return the setting for the selected item only to the 
factory default setting.
 f When color temperature has been changed, the colors before and after the change will dif fer slightly

.
Changing the name of [USER1] or [USER2]
1) Press as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe  [COLOR TEMPERATURE] individual adjustment screen is displayed.
3) Press  qw to select [USER1] or [USER2].
4)  
Press the  button.
 f The  [COLOR TEMPERATURE] screen is displayed.
5) Press  as to select [COLOR TEMPERATURE NAME CHANGE].
6)  
Press the  button.
 f The  [COLOR TEMPERATURE NAME CHANGE] screen is displayed.
7) Press  asqw to select the text, and press the  button to enter the text.
8)  
Press 
 asqw to select [OK], and press the  button.
 fThe name set to color temperature is changed.
Note
 fWhen a name is changed, display of [USER1], [USER2] is also changed.
[GAMMA]
You can switch gamma mode.
1) Press  as to select [GAMMA].
2)  
Press 
 qw or the  button.
 fThe  [GAMMA] individual adjustment screen is displayed.
3) Press  qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT]*1Factory default setting.
[USER1] Allows you to change the name.
Refer to “Changing the name of [USER1] or [USER2]” ( x
  page   68) for details.
[USER2]
[DICOM SIM.] The picture becomes similar to that of DICOM standard.   
						

							Chapter 4 Settings — [PICTURE] menu
68 - ENGLISH
[1.0]Set so that images become as you like. [2.0] - [2.8] can be set in increments of 0.1.
[1.8]
[2.0] 
‑  [2.8]
*1 When [PICTURE MODE] is set to [DYNAMIC], [USER], or [DICOM SIM.], [DEF AUL T] cannot be selected.
Note
 fDICOM is an abbreviation of “Digital Imaging and COmmunication in Medicine” and is a standard for medical imaging devices.  Although the 
DICOM name is used, the projector is not a medical device, and should not be used for purposes such as diagnosis of display images.
Changing the name of [USER1] or [USER2]
1) Press  as to select [GAMMA].
2)  
Press 
 qw or the  button.
 fThe  [GAMMA] individual adjustment screen is displayed.
3) Press  qw to select [USER1] or [USER2].
4)  
Press the  button.
 f The  [GAMMA] screen is displayed.
5) Press the  button.
 fThe  [GAMMA NAME CHANGE] screen is displayed.
6) Press  asqw to select the text, and press the  button to enter the text.
7)  
Press 
 asqw to select [OK], and press the  button.
 fThe selected gamma name is changed.
Note
 fWhen a name is changed, display of [USER1], [USER2] is also changed.
[SYSTEM DAYLIGHT VIEW]
You can correct the image to the optimal vividness even if it is projected under a bright light.
1) Press  as to select [SYSTEM DAYLIGHT VIEW].
2)  
Press 
 qw or the  button.
 fThe  [SYSTEM DAYLIGHT VIEW]  individual adjustment screen is displayed.
3) Press qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] No correction.
[1] Corrects the image to weaken vividness.
[2] Corrects the image to medium vividness.
[3] Corrects the image to high vividness.
[SHARPNESS]
You can adjust the sharpness of the projected image.
1) Press as to select [SHARPNESS].
2)  
Press 
 qw or the  button.
 fThe  [SHARPNESS]  individual adjustment screen is displayed.
3) Press qw to adjust the level.
Operation AdjustmentRange of adjustment
Press the w button. Contours become sharper.
0 - +15
Press the q button. Contours become softer.   
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 69
Note
 fIf you press  w while the adjustment value is [+15], the value will become [0]. If you press  q while the adjustment value is [0], the value will 
become [+15].
[NOISE REDUCTION]
You can reduce noises when the input image is degraded and noise is occurring in the image signal.
1) Press  as to select [NOISE REDUCTION].
2)  
Press 
 qw or the  button.
 fThe  [NOISE REDUCTION] individual adjustment screen is displayed.
3) Press  qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] No correction.
[1] Slightly corrects the noise.
[2] Moderately corrects the noise.
[3] Strongly corrects the noise.
Attention
 fWhen this is set for an input signal with less noise, the image may look dif ferent from what it originally was. In such a case, set it to [OFF].
[DYNAMIC IRIS]
Aperture correction and signal compensation are performed automatically based on the image to result in an image of optimum contrast.
1) Press as to select [DYNAMIC IRIS].
2)  
Press 
 qw or the  button.
 fThe  [DYNAMIC IRIS] individual adjustment screen is displayed.
3) Press  qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] No correction.
[1] Slightly corrects aperture and compensate signals.
[2] Moderately corrects aperture and signal.
[3] Strongly corrects aperture and signal.
[USER] Set any desired correction.
Refer to “Adjusting desired correction amount” (
x
  page   69) for details.
Adjusting desired correction amount
1) Press as to select [DYNAMIC IRIS].
2)  
Press 
 qw or the  button.
 fThe  [DYNAMIC IRIS] individual adjustment screen is displayed.
3) Press  qw to select [USER].
4)  
Press the  button.
 f The  [DYNAMIC IRIS] screen is displayed.
5) Press  as to select [AUTO IRIS], [MANUAL IRIS], or [DYNAMIC GAMMA].
6)  
Press 
 qw to adjust the correction amount.
Item Adjustment
[AUTO IRIS]
(Automatic adjustment of  aperture) [OFF]
No correction.
[1] 
‑  [255] Allows you to set in increments of 1. The larger the value, the 
stronger the correction.
[MANUAL IRIS]
(Fixed adjustment of aperture) [OFF]
No correction.
[1] 
‑  [255] Allows you to set in increments of 1. The larger the value, the 
stronger the correction.   
						

							Chapter 4 Settings — [PICTURE] menu
70 - ENGLISH
ItemAdjustment
[DYNAMIC GAMMA] (Adjustment of signal  compensation) [OFF]
No correction.
[1] Slightly compensates the signal.
[2] Moderately compensates the signal.
[3] Strongly compensates the signal.
Note
 fWhen [DYNAMIC GAMMA] is set to [3], the contrast will be maximized. fBrightness control and dynamic iris operate simultaneously
, but the iris is fully open and does not operate while the brightness is being 
measured.
[SYSTEM SELECTOR]
The projector will automatically detect the input signal, but you can set the system method manually when an unstable signal is input. Set the 
system method matching the input signal.
1) Press  as to select [SYSTEM SELECTOR].
2)  
Press the  button.
3)

 
Press 
 as to select a system format.
 fAvailable system formats vary depending on the input signal.
Terminal System format
 terminal, / terminals Select [AUTO], [NTSC], [NTSC4.43], [PAL], [PAL - M], [PAL - N], [SECAM], or [PAL60].
Set it to [AUTO] normally. (Setting [AUTO] will automatically select [NTSC], [NTSC4.43], [PAL], 
[PAL - M], [PAL - N], [SECAM], or [PAL60].)
Switch the setting to the signal method for the TV used.
 terminal,  terminal 480i, 576i, or 576p signal
Select [RGB] or [YC
BCR].
VGA60 or 480p signal Select [VGA60], [480p YC
BCR], or [480p RGB].
Other movie
‑
based signals Select [RGB] or [YP
BPR].
 terminal 480i, 576i, 480p, or 576p 
signal Select [RGB] or [YC
BCR].
Other movie
‑
based signals Select [RGB] or [YP
BPR].
 terminal 480i, 576i, 480p, or 576p 
signal Select [AUTO], [RGB], or [YC
BCR].
Other movie
‑
based signals Select [AUTO], [RGB], or [YP
BPR].
 terminal Select [AUTO], [480i YC
BCR], [576i YCBCR], [720/50p YPBPR], [720/60p YPBPR], [1035/60i YPBPR], 
[1080/24p
 YPBPR], [1080/24sF YPBPR], [1080/25p YPBPR], [1080/30p YPBPR], [1080/50i YPBPR], 
[1080/60i
 YPBPR], [1080/50p YPBPR], [1080/60p YPBPR], [1080/24p RGB], [1080/24sF RGB], 
[1080/25p
 
RGB], [1080/30p
 
RGB], [1080/50i
 
RGB], or [1080/60i   RGB].
4) Press the  button.
Note
 f Refer to “List of compatible signals” ( x   page   168) for the types of video signals that can be used with the projector . fThis may not function properly for some connected external devices.