Panasonic Projector Pt D10000e Operating Instructions

Information
ENGLISH – 111
Procedure of  lamp unit replacement
1.  Be sure to observe the procedure “Powering up the projector” (p. 35) 
and “Powering off the projector” (p. 36), remove the power plug and 
confirm that the surroundings of the lamp unit have cooled off.
2.  Use a Phillips screwdriver to 
loosen the lamp unit cover screw 
at the rear of the projector until the 
screw turns freely.
3.  Open the lamp unit cover and 
remove it from the projector.
4.  Use a Phillips screwdriver to 
loosen the...

112 – ENGLISH
When installing the ceiling mount bracket to the projector, install the accessory eye bolts and wires to the projector. 
(The projector will still be safe if they are not used, however they will help prevent the possibility of accidents 
caused by the projector falling down if the screws happen to become loose.)
Installation should be carried out by a qualified technician by following the procedure given below.
Panasonic takes no responsibility for any losses or damage occurring as a result...

Information
ENGLISH – 113
 
Before asking for service … try to check the following points again.
Symptoms Check point Page
Power does not turn on
Is the power cord securely plugged in the receptacle? •34
Is the MAIN POWER switch put to the “O” position? •35, 36
Is power supply live at the receptacle? •34
Is the temperature monitor (TEMP) lamp on the projector front 
lighting or blinking? •107
Is the lamp monitor (LAMP) lamp on the projector front lighting or 
blinking? •107
Is the lamp unit cover...

114 – ENGLISH
There is a self-diagnosis display located at the side of the projector (p. 15) which automatically displays error 
details when an error occurs.
  Self-diagnosis display
Self-
diagnosis 
displayDetails Remedy
U04 Air filter is blocked Clean the air filter unit.•
U11 Intake air temperature warning
Ambient air temperature is too high.  • U12 Optical module temperature warning
U13 Lamp ambient temperature warning
U14 Low temperature warning
U21 Intake air temperature error
U22 Optical module...

Information
ENGLISH – 115
Self-
diagnosis 
displayDetails Remedy
F41 Lamp 1 memory error
Problem with lamp. Consult your dealer. • F42 Lamp 2 memory error
F43 Lamp 3 memory error
F44 Lamp 4 memory error
F91 FPGA1 configuration error
If turning the main power off and back on again does 
not clear the error display, consult your dealer. • F92 FPGA2 configuration error
F93 Flash ROM error
F94 RAM error
F95 FPGA expansion error
F96 Lens shift error
FE1 Power supply fan error
FE2 Lamp 1 fan error
FE3 Lamp 2...

116 – ENGLISH
 
Specifications
Model No. PT-D10000E PT-DW10000E
Power supply220 V – 240 V, 50 Hz/60 Hz
Power consumption1 450 W (about 25 W in standby)
Amps8 A
DLP
® panelPanel size0.95 inch (aspect ratio 4:3) 0.95 inch (aspect ratio 16:9)
Display systemThree-unit DLP® chip, DLP® type
Number of pixels3 × 1 470 000 pixels (1 400 × 1 050 dots) 3 × 2 073 600 pixels (1 920 × 1 080 dots)
Lens
(Powered zoom/
Powered focus control)Option
Projection lamp4 bulbs × 250 W UHM lamp
Optical output
*110 000 lm...

Information
ENGLISH – 117
Model No. PT-D10000E PT-DW10000E
Interface 
portsRGB2 input 
terminal1 set of high-density, D-sub 15p (female)
[For YP
BPR input]
Y: 1.0 V [p-p] synchronization signal included, PBPR: 0.7 V [p-p] 75 Ω
[For RGB input] 
0.7 V [p-p] 75 Ω   For G-SYNC: 1.0 V [p-p] 75 Ω
HD/SYNC: TTL, high-impedance, positive/negative polarity automatically adjusted
VD: TTL, high-impedance, positive/negative polarity automatically adjusted
HD/SYNC, and VD terminals are not compliant with 3-value...

118 – ENGLISH
 
Compatible RGB/YPBPR/DVI-D Signals
The following table specifies the types of RGB/ YPBPR/DVI-D signals compatible with the projector.
RGB signals can also be input within the range of fH=15 kHz–100 kHz, fV=24 Hz–120 Hz, dot clock=20 MHz–162 MHz.
Note
The number of display dots of the PT-D10000E is 1 400 × 1 050. If signals with a number of display dots differing 
from the data listed above are supplied, they will be converted into signals with 1 400 × 1 050 dots and displayed.
The number...

Information
ENGLISH – 119
 
List of P IN P
○: P IN P (Picture in Picture) combinations are enabled
×: P IN P (Picture in Picture) combinations are disabled
*1  480i, 576i, 720/60p, 720/50p, 1 035/60i, 1 080/60i, 1 080/50i, 1 080/24sF, 1 080/30p, 1 080/25p, 1 080/24p
*2  480p, 576p, 720/60p, 720/50p, 1 080/60i, 1 080/50i, 1 080/24sF, 1 080/30p, 1 080/25p, 
1 080/24p, 1 080/60p, 1 080/50p
Note
Noise reduction cannot be used with analogue RGB input, DVI input (EDID1 setting) or AUX input (EDID1 
setting)....

120 – ENGLISH
Dimensions
 
Outside dimensions
  Installation dimensions diagram
Attention
Leave a clearance of at least 50 cm so that the ventilation opening on the rear panel will not be blocked.
Set up the projector so that air can flow freely around the rear of the projector without staying still. In addition, 
leave a space of 30 cm or more at the sides so that the hot air coming out from the air outlet vents does not get 
drawn in through the air intake vents.
Set up the projector with a space of 40...