Panasonic Projector Pt Ae8000EH Operating Instructions

							[PICTURE] menu
ENGLISH - 41
Settings
[COLOUR TEMPERATURE]
You can adjust the color temperature if the white 
areas of the projected image are bluish or reddish.Less bluish
Less reddish
 
z Setting range: -6 to +6
[SHARPNESS]
With regards to the input signal, adjust video 
sharpness using one of [SIMPLE] which adjusts 
horizontal direction and vertical direction 
simultaneously or [ADVANCED] which adjusts each 
individually.
Softer
Sharper
Note
 
z Setting range will vary according to the selected input 
signal.
 
z [SHARPNESS] can be adjusted using either [SIMPLE] or 
[ADVANCED]. Both settings cannot be used at the same 
time.
 
z Adjusting the [SHARPNESS].
 
(When [SIMPLE] is selected for the 
[ADJUSTMENT MODE].)
1)   Press 
▲
▼ buttons to select [SIMPLE].
 SHARPNESS
 ADJUSTMENT MODE
 SHARPNESS
 H-SHARPNESS
 V -SHARPNESS SIMPLE
0
PI\fTURE
POSITION
LANGUAGE
3D SETTINGS
LENS \fONTROL OPTION
2)  Select [SHARPNESS] with the ▲▼ 
buttons, and adjust with the 
▲
▼ buttons.
 
z Adjusting the [SHARPNESS].
 
(When [ADVANCED] is selected for the 
[ADJUSTMENT MODE].)
1)   Press the ◄► buttons to select 
[ADVANCED].
 SHARPNESS
 ADJUSTMENT MODE
 SHARPNESS
 H-SHARPNESS
 V -SHARPNESS  
ADVANCED
0
0
PICTURE
POSITION
\fANGUAGE
3D SETTINGS
\fENS CONTRO\f OPTION
2)  Select item with the ▲▼ buttons, and 
adjust with the 
▲
▼ buttons.
 
z Pressing the ▲▼ buttons on the screen during 
adjustment switches to the [H-SHARPNESS] or 
[V-SHARPNESS] adjustment screen.
 H-SHARPNESS
 V
-SHARPNESS 0
0
 
z The setting range varies according to the selected 
picture mode and input signal.
[DYNAMIC IRIS]
You can switch automatic adjustment of the lamp and 
the lens iris on/off. This augments the video to create 
a video expression with sharp contrast between light 
and shade.
Switch settingsSwitch settings
[ON]
Automatic adjustment
[OFF] No adjustment
[WAVEFORM MONITOR]
By using a commercial test disk etc. and setting the 
luminance level of the output (brightness) signal from 
a connected external device to a value within this 
projector’s recommended range, you can perform 
adjustment so the display performance of the projector 
can be fully leveraged.
1)  Press the  button.
 
z The [WAVEFORM MONITOR] menu is displayed.
 WA
VEFORM MONI TOR
     OFF
    FULL  SCAN(Y)
    FULL  SCAN(R)
    FULL  SCAN(\f)
    FULL  SCAN(B)
    SIN\fLE LINE SCA\)N(Y)
    SIN\fLE LINE SCA\)N(R )
    SIN\fLE LINE SCA\)N(\f )
    SIN\fLE LINE SCA\)N(B)
 MONITOR POSITION
  AUTO  AD\bUST UPPER LEFT
2)  
Press the ▲▼ buttons to select the 
required item.
 
z Select [OFF] to close the waveform monitor.
3)  
Press the  button.
 
z The waveform monitor is displayed.
Note
 
z For details, see “Displaying the waveform monitor” in 
“Remote control operation”. (
 page 33) 
						

							[PICTURE] menu
42 - ENGLISH
Settings
 
■ [MONITOR POSITION]
You can set the display position of the input waveform 
during the FULL SCAN display.
Switch settingsSwitch settings
 
■ [AUTO ADJUST]
The luminance level of the output signal from a connected 
external device is automatically adjusted by setting the 
automatic waveform adjustment items.
1)  
Press the  button.
2)   Press the ▲▼ buttons to select the 
required item.
Automatic waveform 
adjustment items Default 
setting
[BLACK LEVEL ADJUST] [ON]
[WHITE LEVEL ADJUST] [ON]
[RGB ADJUST (BLACK)] [OFF]
[RGB ADJUST (WHITE)] [OFF]
3)  Press the ◄► buttons to switch 
adjustment.
4)   Press the ▲▼ buttons to select [START 
AUTO ADJUST] and press the  
button.
 
z [PROCESSING] message is displayed. When 
adjustment is complete, a confirmation message for 
applying results is displayed.
5)  
Select [OK] with the ▲
▼ buttons.
6)   Press the  button.
Note
 
z When [BLACK LEVEL ADJUST] is [ON], the display 
signal Y (brightness) value’s black level is automatically 
adjusted to the 0% position.
 
z When [WHITE LEVEL ADJUST] is [ON], the display 
signal Y (brightness) value’s white level is automatically 
adjusted to the 100% position.
 
z When [RGB ADJUST (BLACK)] is [ON], the display signal 
R (Red), G (Green), and B (Blue) value’s black level are 
all automatically adjusted to the 0% position.
 
z When [RGB ADJUST (WHITE)] is [ON], the display signal 
R (Red), G (Green), and B (Blue) value’s white level are 
all automatically adjusted to the 100% position.
 
z [AUTO ADJUST] cannot be executed if the [WAVEFORM 
MONITOR] is [OFF].
 
z Project the luminance adjustment signal of a commercial 
test disk etc., and perform automatic adjustment. 
However, even with an adjustment disk, correct 
adjustment may not be possible if noise is included on 
the disk itself or the playback device generates noise.  
z [AUTO ADJUST] adjusts based on the 0% and 100% 
standard signal within the screen, so correct adjustment 
cannot be performed if standard signals are not displayed 
on the screen because of overscan etc., or if a signal that 
is less than 0% or greater than 100% is displayed on the 
screen.
 
z When 3D is being displayed (including converting 2D to 
3D), the [WAVEFORM MONITOR] cannot be executed.
 
■ Adjust the waveform
Project the brightness adjustment signal of a commercial 
test disk (0% [0 IRE or 7.5 IRE] - 100% [100  IRE] ) and 
perform adjustment.
 
RETURN
MOVE DISPLA
Y
CHANGE \fF MODE
Adjust to 100%
Signal (luminance) level
Signal (luminance) level
Monitor 
position
Monitor 
position Adjust to 100%
Adjust to 0 %
With COMPUTER (except 1 080 
signal) or HDMI (Expand)
Adjust to 0 % Image 
displayable 
area
Image 
displayable 
area
With the [WAVEFORM MONITOR] displayed, press the 
 button on the remote control and adjust using 
[ADVANCED MENU] and [PICTURE] from the on-screen 
menu. 
						

							[PICTURE] menu
ENGLISH - 43
Settings
1)  Adjust [FULL SCAN(Y)] / [SINGLE LINE 
SCAN(Y)].
 
z Set on [PICTURE] and use the ▲
▼ buttons to 
adjust [BRIGHTNESS] and then [CONTRAST].
[BRIGHTNESS]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
 
z Setting range:  
−32 to +32
[CONTRAST]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
 
z Setting range:  
−64 to +64
2)  
Adjust [FULL SCAN(R)] / [SINGLE LINE 
SCAN(R)].
 
z Set on [ADVANCED MENU] and use the ▲
▼ 
buttons to adjust [BRIGHTNESS R] and then 
[CONTRAST R].
[BRIGHTNESS R]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
 
z Setting range:  
−16 to +16
[CONTRAST R]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
 
z Setting range:  
−32 to +32
3)  
Adjust [FULL SCAN(G)] / [SINGLE LINE 
SCAN(G)].
 
z Set on [ADVANCED MENU] and use the ▲
▼ 
buttons to adjust [BRIGHTNESS G] and then 
[CONTRAST G].
[BRIGHTNESS G]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
 
z Setting range:  
−16 to +16
[CONTRAST G]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
 
z Setting range:  
−32 to +32
4)  
Adjust [FULL SCAN(B)] / [SINGLE LINE 
SCAN(B)].
 
z Set on [ADVANCED MENU] and use the ▲
▼ 
buttons to adjust [BRIGHTNESS B] and then 
[CONTRAST B].
[BRIGHTNESS B]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
 
z Setting range:  
−16 to +16
[CONTRAST B]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
 
z Setting range:  
−32 to +32
Note
 
z When a 3D signal is being input (including converting 
2D to 3D), the [WAVEFORM MONITOR] cannot be 
executed. 
						

							[PICTURE] menu
44 - ENGLISH
Settings
[SPLIT ADJUST]
You can perform image adjustment for some 
[PICTURE] menu items while displaying a certain 
area of the frozen image in a split window.
1)  Press the  button.
 
z The [SPLIT ADJUST] menu is displayed.
SPLIT
 ADJUST
AREA  SELECT
SPLIT  ADJUST  MODE
NORMAL
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION2)  Press the ▲▼ buttons to select [AREA 
SELECT] and then press the  
button.
 
z The image is frozen and an area for adjustment is 
displayed. The image being projected is recorded 
and displayed as a frozen image.
3)  
Use the ▲
▼ buttons to select the area to 
be adjusted.
MOVE  AREA     ENTER : GO  TO SPLIT ADJUST      RETURN : GO  TO FREE\fE SCREEN
Note
 
z Press the  button, and a frozen screen is 
displayed.
4)  
Press the  button.
 
z Split screen display begins.
 
MENU : GO
 TO PICTURE MENU    \
 ENTER :  ADJUSTMENT COMPLETE     RETUR\
N : GO  TO AREA SELECT
MENU : GO  TO PICTURE MENU    \
 ENTER :  ADJUSTMENT COMPLETE     RETUR\
N : GO  TO AREA SELECT
[When [SPLIT ADJUST MODE] is [NORMAL]]
[When [SPLIT ADJUST MODE] is [REVERSE]]
Note
 
z By selecting the [SPLIT ADJUST MODE] with the ▲▼ 
buttons and switching [NORMAL] to [REVERSE], the 
screen displayed on the left during split screen display 
can be reversed and adjusted.
5)  
Press the  button and make 
adjustments with the [PICTURE] menu.
 
z The menu screen is displayed. You can adjust the 
image for optimal display.
PICTURE MODE
CONTRAST
BRIGHTNESS
COLOUR
TINT
COLOUR 
TEMPERATURE
SHARPNESS
DYNAMIC IRIS
\fA VEFORM MONITOR
SPLIT  ADJUST
ADVANCED MENU
PICTURE MEMORY SIMPLE\b
\b
\b
\b
\b
PICTURE
POSITION
LANGUAGE
3D SETTING S
LENS CONTROL OPTION
FRETURN
FUNCTION
ENTER
SELECT xxxxxxxxxxxxxxxxxx\
 
z Items that can be adjusted
Submenu items
Page
[CONTRAST] 40
[BRIGHTNESS] 40
[COLOUR] 40
[TINT] 40
[COLOUR TEMPERATURE] 41
[SHARPNESS] 41
[ADVANCED MENU] 45
6)  Press the  button until getting 
back to the adjustment screen.
7)   Press the  button.
SPLIT  ADJUST
SAVE CHANGES?
YES  : SAVE AND \fUIT
NO  : \fUIT WITHOU T SAVING
CANCEL  : ADJUST  AGAIN
CANCELYESNO
RETURNSELECT
ENTER
 
z The confirmation message is displayed.
 
Select [YES] with the ◄► buttons and press the 
 button to apply the changes and return 
to the frozen screen. 
Select [NO] with the ◄► buttons and press the 
 button to return to the frozen screen 
without applying changes. 
Note
 
z Select [CANCEL] on the confirmation message and press 
the  button to return to the adjustment screen.
8)  
Press the  button.
 
z You can now view the projected video with the 
adjustments applied. 
						

							[PICTURE] menu
ENGLISH - 45
Settings
Note
 
z You cannot adjust menu items that are displayed in grey 
during split adjustment.
 
z The [KEYSTONE] of [POSITION] becomes inactive 
during split adjustment.
 
z When a 3D signal is being input (including converting 2D 
to 3D), the [SPLIT ADJUST] cannot be executed.[ADVANCED MENU]
You can perform more detailed image adjustment 
manually.
Press the  button
 
z The [ADVANCED MENU] menu is displayed.
 ADV
ANCED MENU
 GAMMA  ADJUSTMENT
 CONTRAST   R
 CONTRAST   G
 CONTRAST   B
 BRIGHTNESS  R
 BRIGHTNESS  G
 BRIGHTNESS  B
 NR
 MPEG NR
 \fRAME CREA TION
 COLOUR MANAGEMENT
 x.\b.Colour
 DET AIL CLARITY  ADV
ANCED 1
MODE1
NORMAL 0
0
0
0
0
0
0
0
+3
PICTURE
POSITIO N
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
 
■ [GAMMA ADJUSTMENT]
You can make detailed adjustments to the light intensity 
of each input signal level by using the [ADVANCED1] - 
[ADVANCED8] mode, or adjust at 3 levels (high, mid, low) 
by using the [SIMPLE] mode.
Note
 
z You can only carry out the [GAMMA ADJUSTMENT] 
through either the [ADVANCED1] - [ADVANCED8] or 
[SIMPLE] mode. Both modes cannot be used at the 
same time.
 
 
● Adjusting the gamma  
(when [ADV ANCED1] – [ADV ANCED8] is 
selected in the [ADJUSTMENT MODE])
1)   Press the ▲▼
buttons to select 
[GAMMA  ADJUSTMENT], and press the 
 button.
 
z The [GAMMA ADJUSTMENT] menu appears.
2
)   Pre ss t h e ▲▼
 b utto ns t o  s ele ct 
[ A DJU STM EN T M ODE], a n d t h en  p re ss 
t h e ◄►
 b utto ns t o  s ele ct a n y o ne f r o m  
[ A DVA NCED 1] t h ro ugh [ A DVA NCED 8].
GAMMA  ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
ST AR T ADJUSTMENT
GAMMA  NAME CHANGE
INITIALIZ E AD\f
ANCED1
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION 
						

							[PICTURE] menu
46 - ENGLISH
Settings
3)  Press the ▲▼ buttons to select [START 
ADJUSTMENT], and press the  
button.
 
z The [ADVANCED ADJUST] menu appears.
GAMMA
 ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
ST AR T ADJUSTMENT
GAMMA  NAME CHANGE
INITIALIZ E AD\f
ANCED1
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
4)  Press the ▲▼ buttons to select [GAMMA 
PRESET], and then press the 
◄► buttons 
to change the preset gamma.
 
z The value can be adjusted in the range of -0.40 
to +0.80 with the current gamma value as the 
reference.
ADV
ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f00
ON
PICTURE
POSITIO N
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8Y
R G B
INPUTOUTPUT
50%
100%
40% 0
[-0.40][-0.35]
・・・[+0.75][+0.80]
[R: 0.00 G: 0.00 B: 0.00]
ADV
ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS -\f.4\f
ON
PICTURE
POSITION
LANGUAGE
\bD SETTINGS
LENS CONTROL OPTION
0%POINT 8
Y
R G B
INPUTOUTPUT
50%
100%
40% +18
0% 50%100%
 
z If you select [R: 0.00 G: 0.00 B: 0.00] under 
[GAMMA PRESET], and then press the  
button, the [GAMMA PRESET] menu is displayed. 
Press the ▲▼ buttons to select the [R], [G], or [B] 
row, and then press the ◄► buttons to change 
the preset gamma for each of R, G, and B.
 
z The value can be adjusted in the range of -0.40 to 
+0.80 with the current gamma value as the reference.
GAMMA
 PRESET
R
G
B 0.00
0.00
0.00
PICTURE
POSITION
LANGUAGE
3\f SETTINGS
LENS CONTROL OPTION
0%POINT 8
INPUTOUTPUT
50%
100%
40% 0
5)  Press the ▲▼ buttons to select the [Y], 
[R], [G], or [B] row, and then press the ◄► 
buttons to select any one of [Y], [R], [G], or 
[B]. Finally, press the  button.
 
z The adjustment screen for the selected Y 
(intensity) or each of the colors R, G, or B 
appears, and gamma can be adjusted up to a 
maximum of 15 points.
 
z You can switch between [Y], [R], [G], and [B] 
each time you press the  button.
 
z When you adjust the input level or the output 
level, the menu is deleted, and an adjustment 
screen as shown below appears.
 
z To return to the screen displayed in 4), press 
the  button.
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
INPUTOUTPUT
50%
100%
40% -16
ADVANCED\f ADJUST
GA\b\bA \fPRESET
REFERENCE\fPOINTS +0.40
ON
Y R G B
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
INPUTOUTPUT
50%
100%
40% -36
ADVANC\fD  ADJUST
\bAMMA  PR\fS\fT
R\fF\fR\fNC\f POINTS +0.40
ON
Y R \b B
The information of the currently selected point 
(A) is displayed.
(A) 
						

							[PICTURE] menu
ENGLISH - 47
Settings
POINTDisplay the currently selected 
point number. The number is in 
the order of 1 to 15 starting from 
the lower input level. The selected 
point flashes in yellow on the 
adjustment screen.
INPUT Display the input level of the 
currently selected point. Can 
be set in the range of 1 to 99% 
in increments of 1%. When 
dispatching from the factory, the 
input level is set in the order of 
5%, 10%, 15%, 20%, 25%, 30%, 
35%, 40%, 45%, 50%, 60%, 70%, 
80%, 90%, and 95% starting from 
point 1.
OUTPUT Display the output level of the 
currently selected point. The 
difference from the standard value 
can be set in the range of -252 
to +252. The adjustable range 
depends on the input level. The 
standard value is 0.
6)   Change the POINT, adjust the INPUT level, 
and also adjust the OUTPUT level.
 
z In the screen displayed in 5), select any one 
from [Y], [R], [G], or [B], and then perform the 
operation after pressing the  button.
 
The respective operations are described below.
a.  Changing the point to be adjusted
 
z Press the ◄► buttons to move the cursor for 
selecting the point, to the left or right. 
Press the 
► button to move one point to the right.
Press the 
◄ button to move one point to the left.PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
INPUTOUTPUT
50%
100%
40% -16
ADVANCED\f ADJUST
GA\b\bA \fPRESET
REFERENCE\fPOINTS +0.40
ON
Y
R G B
b. Adjusting the input level (only [Y])
 
z Press the  button to set the 
[OPERATION MODE] to [INPUT ADJUSTMENT]. 
See the operation guide to check if the current 
status is the [CHANGE POINT] mode or the [INPUT 
ADJUSTMENT] mode. 
Operation Guide
OPERA
TION MOD ERESET
(RESET
 ALL: 3 sec\f
OUTPUT ADJ. \bHANGE POINT
RETURN
SET  AS NEW REF.
\bHANNEL
\bHANGE
OPERA TION MODE RESET
(RESET
 ALL: 3 sec\f
OUTPUT ADJ. INPUT ADJ.
RETURN
SET  AS NE\b REF .
CHANNE
L
CHANGE
 
z If you press the ◄► buttons, you can adjust the 
input level of the currently selected point.
 
The input level can be set in the range of 1 to 99% 
in increments of 1%. However, you cannot set an 
input level more than that of the adjoining points.
Note
 
z The input level can be adjusted only when [Y] is being 
adjusted.
 
The input level cannot be adjusted when [R], [G], or [B] 
are being adjusted.
Ex: When the ◄ button is pressed on [Y].
ADV ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f00
ON
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
INPUTOUTPUT
50%
100%
37% +8
ADVANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f0
ON
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
Y
R G B
INPUTOUTPUT
50%
100%
40% 0
Move left 
						

							[PICTURE] menu
48 - ENGLISH
Settings
c. Adjusting the output level
 
z If you press the ▲▼ buttons, you can adjust 
the output level of the currently selected point.
 
z Output level can be adjusted for each color on 
the [Y][R][G][B] screen.
Ex: When the ▲ button is pressed on [Y].
ADV
ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f0
ON
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
INPUTOUTPUT
50%
100%
40% +30
ADVANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f0
ON
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
Y R G B
INPUTOUTPUT
50%
100%
40% 0
Move above
d. Matching the output level to the reference point
 
z In the screen displayed in 4), press the ▲ ▼ 
buttons to place the cursor on [REFERENCE 
POINTS], and then press the ◄► buttons to switch 
to [ON].
ADV
ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f00
ON
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
Y
R G B
INPUTOUTPUT
50%
100%
40% 0
 
z If you display the adjustment screen when 
[REFERENCE POINTS] is set to [ON], the 
reference points are displayed on the screen.
ADV
ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f00
ON
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
Y
R G B
INPUTOUTPUT
50%
100%
40% -16
Reference points (gray)
 
z After selecting any one of [Y], [R], [G], or [B] in the 
screen displayed in 5), you can match the output 
level of the point selected with the ▲▼ buttons with 
the reference point.
ADV
ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f00
ON
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
Y R G B
INPUTOUTPUT
50%
100%
40% -6
 
z By matching the output level of the currently 
selected point with the reference point, the gamma 
value can be created by combining two gamma 
values, such as by setting [GAMMA PRESET] to 
[+0.40] and [+0.30].
 
z You can refresh the reference points by pressing 
the  button of the remote control.
OPERA
TION MODE RESET
(RESET
 ALL: 3 sec\f
OUTPUT ADJ. INPUT ADJ.
RETURN
SET  AS NE\b REF .
CHANNE
L
CHANGE 
						

							[PICTURE] menu
ENGLISH - 49
Settings
Example) When the data for gamma preset value 
+0.40 and gamma preset value 0.00 is combined
1.  Set [GAMMA PRESET] to +0.40, display the 
adjustment screen for any one of [Y], [R], [G], and [B], 
or then press the  button to refresh the 
reference points.
ADV ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS +\f.4\f
OFF
PICTURE
POSITION
LANGUAGE
\bD SETTINGS
LENS CONTROL OPTION
0%POINT 8
Y R G B
INPUTOUTPUT
50%
100%
40% -16
2.  Press the  button to return to the screen 
displayed in 4), and then select [GAMMA PRESET] 
with the ▲ ▼ buttons.
3.   Set [GAMMA PRESET] to [0.00] with the ◄► 
buttons.
ADV ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f00
ON
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
Y
R G B
INPUTOUTPUT
50%
100%
40% 0
The reference points refreshed earlier are displayed.
4.  Select one of [Y][R][G][B] and press the  
button.
5.    Adjust the output level with the ▲ ▼ buttons using 
the reference points as the standard.ADV ANCED  ADJUST
GAMMA  PRESET
REFERENCE POINTS 0\f0
ON
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
0%POINT 8
Y R G B
INPUTOUTPUT
50%
100%
40% 0
Note
 
z If you change the output level of the reference point from 
the preset value, a confirmation screen is displayed when 
changing [GAMMA PRESET].
GAMMA
 PRESET
IF GAMMA PRESET IS USED.
ADJUSTED CUST OM CURVE DATA WI\f\f  BE DE\fETED. 
CANCE\fOK
e. Returning the output level to the default setting
 
z If you press the  button while the output 
level is being adjusted in c. or d. described on the 
previous page, the output level of the currently 
selected point  returns to the default setting.
 
z If you press and hold the  button for 
three seconds or more while the output level is 
being adjusted in c. or d. described on the previous 
page, the output level of all points returns to the 
default setting.
Note
 
z The input level does not return to the default setting even 
when the  button is pressed. 
						

							[PICTURE] menu
50 - ENGLISH
Settings
 
● Initialize the gamma adjustment results
GAMMA
 ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
ST AR T ADJUSTMENT
GAMMA  NAME CHANGE
INITIALIZ E AD\f
ANCED1
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
1)  Press the ▲▼ buttons to select 
[INITIALIZE] and press the  
button.
 
z The confirmation message is displayed for the 
gamma initialization.
GAMMA
 ADJUSTMENT
INITIALIZE GAMMA  ADJUSTMENT.
CANCELOK
2)   Select [OK] with the ▲
▼ buttons and press 
the button.
 
z [ADVANCED 1] - [ADVANCED8] are all 
set to the factory default setting, and 
the [ADJUSTMENT MODE] is set to 
[ADVANCED1].
Note
 
z Initialization is not available in [SIMPLE] mode.
 
z You cannot execute [INITIALIZE] when two screens are 
being adjusted.
 
● Adjusting the gamma (when [SIMPLE] is 
selected for [ADJUSTMENT MODE])
1)  
Press the ◄► buttons to select [SIMPLE].
GAMMA  ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
ST AR T ADJUSTMENT
GAMMA  NAME CHANGE
INITIALIZ E SIM\fLE
0
0
0
\fICTURE
\fOSITION
LANGUAGE
3D SETTINGS
2)   Select item with the ▲▼ buttons, and 
adjust with the 
▲
▼ buttons.
 
z You can adjust linear intensity at 3 levels (high, 
mid, low). Press ▲ ▼ to select your required 
gamma levels.
-1+1
 
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW 0
0
0
[ADVANCED MENU] menu items
Default 
setting
[GAMMA HIGH] 0
[GAMMA MID] 0
[GAMMA LOW] 0
 
z Setting range: -8 to +8